In this task, you are suggesting a suitable design for a compressor to be used for gas power plant. You client has asked you to suggest a design for a compressor, where air is compressed from 100 kPa and 30℃ to 10 bar. Prepare a technical design report using following criteria in your design To optimise the final temperature of the gas, you are asked to use various polytrophic compression process. Calculate the final temperature when the process is: Isothermal,Polytropically (n=1.2),AdiabaticallyPolytropically (n=1.6).Comment on your findings and recommend appropriate process for compression by calculating work input.

Given:P1=100 KPaT1=30°C =293 KP2=10 bar =1000 KPa NOTE: According to Bartleyby's policy we shall…

rature of the gas, you are asked to use various polytrophic compression process. Calculate the final temperature when the process is: Isothermal, Polytropically (n=1.2), Adiabatically Polytropically (n=1.6). Comment on your findings and recommend appropriate process for compression by calculating work input.

rature of the gas, you are asked to use various polytrophic compression process. Calculate the final temperature when the process is: Isothermal, Polytropically (n=1.2), Adiabatically Polytropically (n=1.6). Comment on your findings and recommend appropriate process for compression by calculating work input.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter9: Heat Transfer With Phase Change

Section: Chapter Questions

Problem 9.4DP

See similar textbooks

Similar questions

Section C 5. (a) Air is compressed in a diesel engine cylinder. The initial pressure and temperature are 105 kN/m and 25 °C respectively, and the final pressure is to be 7 MN/m. In order to ignite the fuel charge injected at the end of compression, the temperature required is 700°E. Calculate the ratio of the initial to final volume for this to be possible. Assumtng that the compression process is polytropic, find the polytropic index of the compression process.
The pressure of the air in a starting vessel is 40 bar and the temperature is 24°C. If a fire in the vicinity causes the temperature to rise to 65 °C. Neglect anyincrease in the volume of the vessel which is 5 liters. determine the: a. work nonflow and heat transferred
6.1 Dry saturated steam is expanded in a steam nozzle from 1 MPa to 0.01 MPa. Calculate dryness fraction of steam at the exit and the heat drop.
Evaporator, single effect is used to upgrade the concentrate 8000 kg/h of tomato juice than 5% solids the total to 30% solids total. Juice enters the Evaporator at 20 °C. The Evaporator is operated with Steam (quality 80%) in 143.27 kPa. The condition of vacuum in the Evaporator allow the juice to a boil on the 75 °C. The hot kind of material dilute is 4.1 kJ/(kg °C) and the product the concentrate is a 3.1 kJ/(kg °C). Count (a) the Rate of the needs of steam = kg/h. b. The economic steam if the temperature is condensate is released at 75 °C. = (kg water evaporated/kg of steam)
Pls solve accurate and fast A 1-kg steam-water mixture at 1.0 MPa is contained in an inflexible tank. Heat is added until the pressure rises to 3.5 MPa and the temperature to 400: Determine the heat added
How many tons of refrigeration are required to produce 10 metric tons of ice per day at -10 °C from raw water at 22 °C if miscellaneous losses are 15% of the chilling and freezing load? 3.
A single acting, twin cylinder, Ammonia compressor with bore equal to stroke is driven by an engine at 250 rpm. The machine is installed in a chilling plant to produce 700 kW of refrigeration at -18°C evaporating temperature. At this temperature the cooling effect per kg mass is 1160 kJ. The specific volume of vapor entering the compressor is 0.592 m³ per kilogram. Assume 85% volumetric efficiency, determine the bore in mm.
HVAC UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS. please anwer all the subquestions. thank you. 3. Air at 22°C db & SATURATED Solve for the following: a. RH b. DPT c. V d. h e. RH
For air properties use online source: https://www.peacesoftware.de/einigewerte/luft_e.html The compressor is operating at steady-state increasing pressure of R-22 refrigerant from 4 bars to 14 bars. Temperature was rising during the process from 12C to 90C. The inlet volumetric flow rate is 1 m3/min and inlet diameter is 0.03m. At the exit the diameter is the same. Heat flow to the surroundings can be neglected. Determine: a.Mass flow rate [kg/s] b. Inlet and outlet velocity [m/s] c.Power required to run the compressor [kW]
For air properties use online source: https://www.peacesoftware.de/einigewerte/luft_e.html The compressor is operating at steady-state increasing pressure of R-22 refrigerant from 4 bars to 14 bars. Temperature was rising during the process from 12C to 90C. The inlet volumetric flow rate is 1 m3/min and inlet diameter is 0.03m. At the exit the diameter is the same. Heat flow to the surroundings can be neglected. Determine: a.Mass flow rate [kg/s] SHOW AND EXPLAIN ALL STEPS PLEASE thanks
For air properties use online source: https://www.peacesoftware.de/einigewerte/luft_e.html The compressor is operating at steady-state increasing pressure of R-22 refrigerant from 4 bars to 14 bars. Temperature was rising during the process from 12C to 90C. The inlet volumetric flow rate is 1 m3/min and inlet diameter is 0.03m. At the exit the diameter is the same. Heat flow to the surroundings can be neglected. Determine: a.Mass flow rate [kg/s] SHOW AND EXPLAIN ALL STEPS PLEASE
For Problem 2, What is the temperature at core turbine outlet? The power produced by the core turbine must equal the power into the core compressor; since we are assuming a perfect gas with the properties of air and treating the combustion as equivalent to a heat transfer, the temperature drop in the core turbine must equal the temperature rise in the core compressor. If the temperature of the gas leaving the combustor (i.e. entering the HP turbine) is 1450K, find the temperature at core turbine outlet and thence the pressure at outlet from the core turbine. Assume a turbine efficiency of 90%. (Neglect any pressure drop in the combustor.) Fan bypass stator LP Turbine LP Booster stoge Byposs jet Fan Core Rotor HP Compressor Combustor Core nozzte 2-stage HP turtine Byposs nozzie