R (3) Q R A B D P=32 kips_Q=29 kips R=34 kips The normal stress magnitude in aluminum rod (1) must be limited to 20 ksi......... steel rod (2) must be limited to 30 ksi .... in brass rod (3) must be limited to 23 ksi. Determine the minimum diameter required for the brass rod. Answer in inches rounded-off to 2 decimal places.

R (3) Q R A B D P=32 kips_Q=29 kips R=34 kips The normal stress magnitude in aluminum rod (1) must be limited to 20 ksi......... steel rod (2) must be limited to 30 ksi .... in brass rod (3) must be limited to 23 ksi. Determine the minimum diameter required for the brass rod. Answer in inches rounded-off to 2 decimal places.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the maximum normal stress (in Mpa) in bar ABCD if the cross-sectional area of the bar is A = 556 mm2 and P= 36.79 kN. Round off the final answer to four decimal places.
(1) Given: b₁ B P=28 kN Square Bars b₁ = 57 mm (2) Q =9 kN b2 C b₂ = 19mm (3) Q R = 38kN ↑ D b3 = 38mm R WHAT IS THE AXAIL STRESS IN BAR 2? ANSWER IN MPa ROUNDED-OFF TO 2 DECIMAL PLACES. POSITIVE FOR TENSILE STRESS AND NEGATIVE FOR COMPRESSIVE STRESS.
The internal loadings at a section of the beam in (Eigure 1) are shown Figure 20 mm 100 mm 200 mm 20 mm 10 kNm 20 mm 10/12 60 kN 80 KN 500 N-m Determine the in-plane principal stresses at point C. Also compute the maximum in-plane shear stress at this point Express your answers, separated by commas, to three significant figures. VAZ Ivec 4 d Submit Provide Feedback T Wha Bequest Answer ? MPA, MPA, MPA
The state of plane stress shown occurs at a critical point of a metal machine component. As a result of several tensile tests, it has been found that the tensile yield strength is Fy for the grade of metal used. Determine the ratio of OT/ OH shown in the figure, using the maximum-shearing-stress criterion (Tresca Hexagon). (Using Mohr circle method to calculate principle and average stresses) OX TXy Mpa Mpa Mpa MPa ob σy тху 90 -60 45 310 dy OX x Sx=Sx Sy=sy txy=txy Fy=Yield Strength Answer
A pipe has an outside diameter of 0.7 inches and inside diameter of 0.12 inches. A force of 411 lbs is applied at the end of a 1.7 in lever arm, causing the pipe to twist. What is the maximum stress in the pipe in psi? 20,766.9 Correct Answer: 124,601
A state of stress at a point A is given by σx = 77 MPa, σy = 3.1 MPa, and τxy = 12 MPa. What is the maximum in-plane shear stress for the point A? Lütfen birini seçin: a. 70.7106 MPa b. 38.8497 MPa c. 83.0846 MPa d. 39.4498 MPa e. None
(1) Given: B P=28 KN Square Bars b₁ = 57 mm (2) Q =9 kN b₂ C b₂ = 19mm (3) Q R = 38 kN ↑ D b3 = 38mm R WHAT IS THE AXAIL STRESS IN BAR 2? ANSWER IN MPa ROUNDED-OFF TO 2 DECIMAL PLACES. POSITIVE FOR TENSILE STRESS AND NEGATIVE FOR COMPRESSIVE STRESS.
A steel pipe has an inside diameter of d = 250 mm and an outside diameter of D = 268 mm. The length of the pipe is L = 6.0 m. The changes in dimension caused by an increase in temperature of 80°C for the: Outside diameter - Blank 1 mm Inside diameter - Blank 2 mm Lenght - Blank 3 mm Note: All answer must be round off up to 3 decimal places.
Question 1 Aluminum rod E = 10400 ksi Allowable axial deformation= 0.3 in. Tension in the rod=2300 lb. allowable normal stress in the rod = 12.8 ksi, Determine the the corresponding maximum length L of the rod. Answer in inches rounded-off to 2 decimal places
A steel pipe with an outside diameter of 115 mm and an inside diameter of 105 mm supports the loadings shown. Assume a = 510 mm, b = 230 mm, Px = 20 kN, P, = 16 kN, and P, = 11 kN. (a) Determine the normal and shear stresses on the top surface of the pipe at point H. (b)Determine the principal stresses and maximum in-plane shear stress magnitude at point H and show the orientation of these stresses on an appropriate sketch. a |P, y P: P H K
Q2- Show the stress components of a point in plane stress on the square in Figures below: Ty = 18 ksi Oy = 85 ksi (T) = 27 ksi (C) Oxx 1- 18 ksi %3D = 100 MPa (T) =-75 MPa 2- = -75 MPa = 85 MPa (T)
6. JA line shaft rotating at 200 r.p.m. is to transmit 20 kW. The allowable shear stress for the material of the shaft is 42 MPa. If the shaft carries a central load of 900 N and is simply supported between bearing 3 metre apart, determine the diameter of the shaft. The maximum tensile or compressive stress is not to exceed 56 MPa. [Ans. 50 mm] ort Fach nulley is 100