Question: a student has chosen the particular weight of 1.373 kg for gear and optimised is by getting the following plot. Taking into consideration these points. A) comment on the plot? B) why high contact stiffness ratio is important and high mesh as well? Contact stiffness 23.0 21.0 19.0 90 17.0 57 72 67 62 15.0 28 $2 $2931 2325 3032 26 27 18 21 Normal module [mm] 4.600 82 2.862 63 1.125 13.0 1.000 1.100 1.200 1.300 1.400 1.500 1.600 1.700 Total contact ratio

Question: a student has chosen the particular weight of 1.373 kg for gear and optimised is by getting the following plot. Taking into consideration these points. A) comment on the plot? B) why high contact stiffness ratio is important and high mesh as well? Contact stiffness 23.0 21.0 19.0 90 17.0 57 72 67 62 15.0 28 $2 $2931 2325 3032 26 27 18 21 Normal module [mm] 4.600 82 2.862 63 1.125 13.0 1.000 1.100 1.200 1.300 1.400 1.500 1.600 1.700 Total contact ratio

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

zain 10 2G 3G zain IQ Z Questions of Lectu... -> Questions of Lecture Five: Q1)) Define the following: 1) The stress & the strain 2) Mechanical stress and mechanical strain 3) yield strength and tensile strength 4) Modulus ofelasticity and the strain hardening Q2)) Fill the following blanks: 1)) Tensile tests are used to 3)) The most application tests of applied static stresses to which materials can be subjected are ---------, ---------, --------- 4)) Tensile stresses cause ---------, and compressive stresses ----------, while shear stresses ----------, of the material. 5)) Engineering stress-strain is important in ----------, while the true stress-strain is important in ---------- 6)) The unit of mechanical stress is --------- or ----------, while the unit of strain is n compression test, when specimen is compressed, its height is ---------, and its cross-sectional area is 8)) Compression is in contrast to the tensile, the compression test contributes to the ----------, in stress…
Weights measured in grams of randomly selected M&M plain candies: 0.957 0.912 0.925 0.886 0.920 0.958 0.915 0.914 0.947 0.939 0.842 What is the z-score for an M&M that weighs less than 0.866 grams? (round to the tenths place)
Report Sheet FRICTIONAL FORCES Data: Total Mass (g) Normal Force (N) Static Friction (N) Kinetic Friction (N) 120 1.35 aso 2.5 360 3.8 440 4.8 Include a graph of frictional force as a function of normal force with both data sets on the same graph Record the slope of each line as the coefficients of friction. Coefficient of static friction: Coefficient of kinetic friction: Questions: 1) Why must the coefficient of static friction always be greater than or equal to the coefficient of kinetic friction? 2) Why do items begin to slide down an inclined plane as the angle is increased? (A free body diagram may be helpful.)
You have a 81.4% efficient pulley system arranged such that the effort pulls upward. Suppose that this system requires 139 N of effort pulling for 14.6 m, in order to lift the load up by 3.65 m. Answer tolerance of ±1 on the third signficant digit, unless noted otherwise. a) Determine the ideal mechanical advantage of this system. Must have absolute accuracy! Number b) Determine the actual methanical advantage of this system. Number c) Determine the number of fixed pulleys in this system. Must have absolute accuracy! Number d) Determine the weight of the load, in N. Number
b) A sedan car weights 2100 kg with 45:55 distributions front to rear. The car has wheelbase of 1.9 m. With aid of following table showing the tyre cornering stiffness values for different loads: Load Cornering Stiffness (kg/deg) 300 131 400 149 500 174 600 203 i) Calculate the cornering coefficient for the front and rear tyres. ii) Calculate the understeering gradient. iii) Determine whether it is understeer or over steer. iv) Calculate critical or characteristic speed.
Please solve this question in 50 mins i will give you positive feedback. Donot miss any subpart clearly mention each subpart
Mechanical Engineering xyz= 703 Stress, ksi (log) 72 49 35 28 10³ 8 x 10³1 10¹ 401 X 8't 49 ksi 10 ksi 401 X 9'1 35 ksi 28 ksi 105 Cycles (log) 106 19.8 The provided S-N curve shows the fatigue strength of a ferrous component with unknown geometry. 107 Given the following duty record, how much life is consumed at each stress level? 60 ksi 500 cycles 2000 cycles (600 000 + XYZ*100) cycles (15000 + XYZ) cycles 40000 cycles
Match the following statements with the term that best describes each statement. (Enter Number ONLY) 1) Hooke's Law 2) Creep 3) Impact Strength 4) Proportional Limit 5) Fatigue 6) Elastic The tendency of a solid material to move slowly or deform permanently under the influence of mechanical stresses below the yield strength of the material. The behavior of materials that deform when loaded but return to their original shape after the load is removed. The linear relationship between stress and strain in the elastic region below the proportional limit. The phenomenon where cracks propagate under loads less than the yield stress due to cyclic loading. The material property determined using the Charpy or Izod test. The point at which the stress vs strain becomes non-linear in an elastic material,
In the context of our teaching and learning, which one of the below statements is mostly correct about in the creation of detailed design of a component? In deciding the tolerance, the guidance is the tighter the better. I am the designer, so I decide the required tolerance as l like. The tolerance is determined by the function. The chance to manufacture component to the exact size is like to win a lottery. I would enjoy winning a lottery, so I should specify all the dimensions as exact, no tolerance to be considered at all.
The gear shown is a 'right hand' helical gear? Select one: O True O False ous page earnonline.gmit.ie/mod/quiz/attempt.php?attempt3D167036&cmid%3D155306&page%3D3... *** Typo bo
71.7 is being marked wrong in McGraw Hill homework. I thought I had done it right with putting 86.03 but that is wrong also. I'm not trying to just find the answer, trying to find how to do this. Could there be a different number than 71.7? Where does the μk=0.20 come into the equation?
Match the terms precision and accuracy to their definitions. Precision 2 Accuracy Match each of the options above to the Items below. The number of significant digits or the closeness of different measurements of the same quantity to each other. The closeness of the measured or calculated value to the true value 1 2