Question A sinusoidal signal with a peak voltage of 10V is input into a frequency dependent circuit. What is the peak voltage at its -6dB frequency?
Q: QUESTION 7 With reference to PLC discrete output modules: What types of fi eld output devices are…
A:
Q: 4- A system with a dynamic equation: The input matrix is 2x(t) + 10X(t) = 3u(t) ----------- and the…
A: Given, 2X...t+10X..t=3ut Here, we have to find the input matrix and poles of a system.
Q: Use the duality property to find the inverse transforms of the following functions: F(w) 10u(w) - 5…
A: Since you have posted the multiple questions so we are supposed to answer the 1st one.
Q: A balanced abc-sequence Y-connected source with Van -220L 0° V is connected to a delta-connected…
A:
Q: An amplifier operating from a +15V power supply provides a 12V peak-to-peak sine- wave signal to a…
A:
Q: RN at terminals Fig. 3.191 (i). Find the values of in and ab for the circuit shown in
A: We have an circuit as shown in figure, We have been asked to find the values of IN and RN which are…
Q: Consider the Given Figure, where Ves = 4V. Ra=220Kohm, Rc = 2Kohm, Vcc= 10V. Vgg (on) = 0.7V, the…
A:
Q: The Commonly Used Types of Power Supply Use and Applications of power supply
A: A power supply can be described as an electrical device used to provide energy to consumers. These…
Q: An energy meter makes 100 revolutions of its disc per unit of energy. The number of revolutions made…
A:
Q: Q1: Check the following discrete time system are: y(n) = 55 x(n) + 8 nx(n – 8) 1. Static or dynamic.…
A:
Q: A single phase transformer has turns ratio of 4. The resistance and reactance of the primary winding…
A:
Q: How does the shape of wires carrying current affect the shape of the magnetic field created?
A: Magnetic field: The expression field of force connected to shifting electric fields, such as when…
Q: Three resistors of 12Ω , 52Ω and 72 Ω are connected in parallel. If the total current is 100 A, how…
A:
Q: Kindly answer this An alternating voltage is given by v=282.8 sin 314 t volts. Find (a) the RMS…
A: An alternating voltage is given by v=282.8 sin 314 t volts Vrms ? Frequency? The instantaneous…
Q: 2. Given a system with input x(t) and impulse response h(t) given by: x(t) = t³u(t) and h(t) =…
A: Given that Input is given by x(t) and impulse response is given by h(t). xt=t3 utht=t2 ut Find the…
Q: Find the Fourier transforms of the following waveforms: fi(t) = 2u(t)- 2 f₂(t) = 30j4t sgn(t) f3(t)…
A:
Q: Write the equation of unit step function for the figure below.
A:
Q: Queston- A capacitor of 10 uF takes a current of 2A when an alternating voltage is applied across is…
A: Given- Capacitance- C=10 μF=10×10-6 F,I=2 A,V=220 V, To Find- The frequency of the applied voltage.…
Q: Question 3 Find 11, 12, 13, and Vo in the following circuit. Use diode constant voltage drop (CVD)…
A: Given data: V1=10 V, V2=5 V, V3=1 VR1=30 kΩ, R2=100 kΩVDo=0.5 V
Q: 4.) Please solve Problem B-2-5 from Ogata (page 61). Please disregard the variable s in the given…
A: Given closed loop system,
Q: 5. For the circuit shown in the figure below, calculate the followings- ii) Z (consider r=00) iii)…
A:
Q: Find the transfer function, 0₂ (s)/T(s), for the system below: Ra +-W eg(t) T (N-m) 150 J₁ = 4 kg-m²…
A: Please comment if you need any clarification. If you find my answer useful please put thumbs up.…
Q: Determine whether or not each of the following signals is periodic. If a signal is periodic,…
A:
Q: a. Find the voltage and current across resistor R2. Also indicate the value of the current through…
A:
Q: choose the correct expression for (A + B C D O A+B+CD B + C + D B + C + D A B + C + D A OA ||
A: Given a Boolean expression, F=A+B¯.C.D¯
Q: What is the impedance of an inductor of 5mH at a radian frequency of 2x10^3 rad/s? Z= ohms
A: Given: An inductor has the specifications, Inductance, L=5 mH. Frequency, ω=2×103 rad/s.
Q: calculate the gate input of F=AB + C(D+E)
A: Given: F=AB + C(D+E) To calculate: the gate input of F
Q: 6. If the rms current through a 4.7 kn resistor is 4 mA, the peak voltage drop across the resistor…
A: The peak voltage is the maximum voltage of the input and the rms voltage is the average voltage of…
Q: 1- A unity positive feedback system with a plant G(s) has transfer function: G(s) 1+G(s) G(s) G(s)…
A: As per our guidelines, when student post multiple questions we have to solve first three questions.…
Q: . For each of the signals in (a)-(g) below, determine which of the properties (1)-(6) listed here is…
A: As mentioned in the question, we'll solve only three parts (a), (c) and (d) Given: Signal x[n] in…
Q: Find the voltage drop across a toaster that gives off 7500 Joules heat when a 13.64 Amps current…
A: Given: A toaster gives off heat H=7500 J. Current through toaster is I=13.64 A. Time t=5 s.
Q: 6. If the rms current through a 4.7 kn resistor is 4 mA, the peak voltage drop across the resistor…
A: According to Ohm's law, V=I*R V=potential difference between two terminals I= current flowing…
Q: Q5/Find the solution of the following operation for binary numbers 11010.101-100101.010…
A:
Q: (i) Find the value of resistance R in the figure below if the voltmeter reads 12 V and ammeter reads…
A: Given- Case-(i), Voltmeter reading=12 V, Ammeter reading=0.100 A. To Find- The value of resistance…
Q: An inductive load consisting of R and X in parallel feeding from a 2400-V rms supply absorbs 288 kW…
A:
Q: A discrete-time system has the following unit-pulse response, Find the response of this system y[n]…
A:
Q: A 240 kV, 3-phase, 50 Hz, 400 km transmission line has a capacitance to earth of 0.04 µF/km per…
A: We have a 3-phase transmission line having, Line voltage (V) = 240 KV = 240 * 103 V frequency (f) =…
Q: Compute the convolution x[n] *h[n] for all n ≥ 0, by using Graphical or Tabular method.…
A:
Q: Prepare an assembly chart for a table lamp.
A: An assembly chart is model that shows which part are to be fitted together and the overall view of…
Q: Compute the convolution x[n] *h[n] for all n ≥ 0, by using Graphical or Tabular method.…
A:
Q: F', (S) (2) a-Find a transfer function G(s) = V (s) the output. of the circuit shown below, where is…
A: Transfer function is ratio of laplace transform of output to laplace transform of input, keeping…
Q: A 60 MVA, 3 phase, 11 kV synchronous generator is protected by the Merz-Price protection using 1000/…
A:
Q: ISC (Lapt KCL @@ Node A: I₁ = Io +1₂ @ KVL @ loop 1 A I To 1₂ 10 1₁ + 51 -15V + 10V=0 101 +5 KVL @…
A:
Q: 39А 130 ли 31 The circuit above is in DC steady state. What is the value of i, in amps? 9Н
A: Given data, Circuit diagram is given as,
Q: An AC motor takes 10 A when connected across a 240 V, 60 Hz source. Determine: the power factor of…
A:
Q: Q5/Find the solution of the following operation for binary numbers 11010.101-100101.010…
A: In a digital computer, signed numbers are represented using two's complement. Simply invert the…
Q: A 6 pole, 50 Hz, 3 phase, star connected motor has an impedance of 0.016 ohm and a fixed time…
A:
Q: For each function g(t), plot the g(-t), -g(t), and g(t-1) of the functions below. g(t) 3- и
A:
Q: 4 Pole's DC generator delivers a current of 100 A at 230 V. It has 1500 armature carriers attached…
A:
Q: 2. Find i 4Ω Μ ΖΩ WWW Μ 10 Ω i 19 8V 6V www 5Ω
A:
Step by step
Solved in 2 steps
- 2. For the below figure - a) Derive the output and minimize the output function using Karnaugh map b) Draw the wave form of output if BComplete solution and Draw the waveform of the given clamper circuit.Determine: 1. At +20V, what is the output voltage?2. At -10V, what is the output voltage?3. At 0V, what is the output voltage?Draw the waveform of the given clipper circuit and determine the following: a.) At 0V, what is the output voltage?b.) At +20V, what is the output voltage?c.) At -5V, what is the output voltage?
- Using a positive Clamper Circuit, with an AC voltage of Vi = 100v with a frequency of 30hz, a value of 1000u for the Capacitor, a silicon diode and a resistor with the value of 100 ohms. Find the voltage value on the resistor at a simulation of Oms. Vm 2Vm Vo -Vm Input Waveform Output Waveform Positive Clamper circuitA 10 V peak-to-peak sinusoidal voltage is applied across a silicon diode and series resistor. The positive peak voltage across the diode is а. 9.3 V b. 4.3 V c.0.7 V d. 10 VThe waveform on the screen of horizontal division an oscilloscope is 4 squares high from bottom to top, as in the Figure below. sensitivity is Volts/Div, what is the peak- to-peak bottom) of the input signal, and what is the amplitude of vertical division If the 2.5 horizontal divisions set to 0.2 voltage (top-to- 4 vertical divisions the oscillation?
- Using a positive Clamper Circuit, with an AC voltage of Vi = 100v with a frequency of 30hz, a value of 1000u for the Capacitor, a silicon diode and a resistor with the value of 100 ohms. Find the voltage value on the resistor at a simulation of Oms. Vm 2Vm Mr. Vm Vo -Vm Input Waveform Output Waveform Positive Clamper circuitUsing a positive Clamper Circuit, with an AC voltage of Vi = 13v with a frequency of 60hz, a value of 100u for the Capacitor, a silicon diode and a resistor with the value of 1000 ohms. Find the voltage value on the resistor at a simulation of 20ms. 2Vm Vm Vm Vo -Vm Input Waveform Output Waveform Positive Clamper circuitThe waveform displayed on an oscilloscope is as shown in Figure The 'time/cm' switch is set to 0.2 ms/cm, and the 'volts/cm' switch is set to 40 V/cm. Determine the (i) amplitude of waveform Q, (ii) peak to peak value of waveform P, (iii) frequency of waveform P