Question 33 Students in the Momentum Transfer Laboratory class at Adamson University use the device set-up shown in the figure below to measure the density of water: A tank and a smooth tube. The flow is laminar and has negligible velocity head loss due to sudden contraction. The measured values were as follow: The volumetric flow rate of 0.52 cubic centimeter per second was measured using a stopwatch and a graduated cylinder. • Tube diameter (do) = 1.2 mm • Tube length (h) =0.92 meter • Water level height in the vessel (Z) = 0.15 meter; • Viscosity = 0.0011 kg/m-s. This was measured using viscometer The mass flow rate of water in kilogram per hour is Blank 1 kg/hr ***EXPRESS YOUR ANSWER in TWO (2) DECIMAL PLACE and WITHOUT UNITS**** Water height, Z tube diameter (do) h Mass flow rate (m) www

Question 33 Students in the Momentum Transfer Laboratory class at Adamson University use the device set-up shown in the figure below to measure the density of water: A tank and a smooth tube. The flow is laminar and has negligible velocity head loss due to sudden contraction. The measured values were as follow: The volumetric flow rate of 0.52 cubic centimeter per second was measured using a stopwatch and a graduated cylinder. • Tube diameter (do) = 1.2 mm • Tube length (h) =0.92 meter • Water level height in the vessel (Z) = 0.15 meter; • Viscosity = 0.0011 kg/m-s. This was measured using viscometer The mass flow rate of water in kilogram per hour is Blank 1 kg/hr *EXPRESS YOUR ANSWER in TWO (2) DECIMAL PLACE and WITHOUT UNITS** Water height, Z tube diameter (do) h Mass flow rate (m) www

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A U-tube manometer is arranged, as shown in Fig. 2.15, to measure the pressure difference between two points A and B in a pipeline conveying water of density 1000 kg/m³. The density of the manometric liquid Q is 13600 kg/m³ and point B is 0.3 m higher than point A. Calculate the pressure difference when h = 0.7 m. T Manometric liquid Q of density Pman Figure 2.15 Measurement of pressure difference Fluid P, of density blup all to 20 lens
Q3: A pitot-static tube is used to measure the flow velocity of turpentine flowing in a pipeline if the manometer reading is 8 cm of mercury, calculate the average velocity, pressure drop, and volumetric flow rate at that point in the pipe line. Also evaluate Reynold number for turpentine and which type of flow in the pipe. Ph J Re Density of turpentine is 850 kg/m³, density of mercury is 13600 kg/m³, cv = 1, D=10 cm, turpentine 0.001375 and 0 = 45°. =
b) The U-tube manometer can be used to determine pressure difference between two systems.This type of manometer is called a differential U-tube manometer. Consider the differentialmanometer connected to a pipe, as shown in Figure 1. Explain step by step on how you cancalculate the pressure difference between point A and B.
As shown in Figure 1, an ideal gas flows isentropically from a large tank into a converging nozzle and exits to a receiver. The gauge pressure of the ideal gas in the large tank is 80 kPa. The nozzle exit area is 38 cm?. (Assume Pam = 101 kPa). a) Determine Mach Number at section 1, the EXIT mass flow rate and EXIT Mach mumber. b) Calculate the flow area at section 1. V: = 580 km/hr T:= 500 K Exit, A Large Tank P= 166 kPa (abs) Ideal Gas k=1.43 R= 0.2968 kJ/kg.k Vi = 480 kan/hr Figure 1
A differential "U"-tube manometer containing mercury of density 13000 kg/m³ is used to measure the pressure drop along a horizontal pipe. If the fluid in the pipe is water and the manometer reading is 0.65m, what is the pressure difference between the two tapping points? Fluid density Pw A B a b datum Manometric fluid density p Hg Figure of manometer setup
Q4: A 7-cm diameter solid aluminum ball (SG = 2.7) and a solid brass ball (SG-8.5) balance nicely when submerged in a fluid as shown in figure. a) If the fluid is water, what is the diameter of the brass ball? b) If the brass ball has a diameter of 3.8 cm, what is the density of the fluid? 2 pulleys Fluid brass aluminum D= 7 cm +
A tube of diameter 25 mm is used (as shown in the below figure) as a siphon to discharge water from a large open vessel into a drain at atmospheric pressure, (Given: Atmospheric pressure = 101.325 kPa) ignoring friction losses (3) (1) Determine (a)Velocity of flow through syphon (b)Discharge through the syphon (c)The minimum pressure inside the syphon (2) 160 mm 80 mm, 100 mm
Q4 The apparatus shown in the figure is used lo measure the velacily of air at the center of a duct having a 10 cm diameter. A tube mounted at the center of the duct has a 2 mm diameter and is attached to one leg of a slant-tube manometer. A pressure tap in the wall of the duct is connected to the other end of the slant-tube manometer. The well of the slant-tube manometer is sufficientiy large that the clevation of the fluid in it does not change significantiy when fluid moves up the leg of 10 em r-20C the manometer. The air in the cuct is at a temperature of 20°C, and the pressure is 150 kPa. The manometer liquic has a specfic gravity of 0.7, and the slope of the leg is 30. When there is no flow in the duct, s-0.7 the liquid surface in the manometer lies at 2.3 cm on the slanted scale. When there is flow in the cuct, the liquid moves up to 6.7 cm on the slanted scale. Find the velocity of the air in the duct. Assuming a uniform velocity profile in the duct calculate the rate of flow…
A mercury manometer is connected to a flow meter in a pipeline. The gaugepressure at Point 1 is 38 kN/m2 and at Point 2 the vacuum pressure is −50 kN/m2. The fluid in the pipeline is water. Calculate the manometer reading Rp .
Qsn. Plot the flow curve of liquid limit according to the data given in the table.
The apparatus shown below is filled with two types of liquid: one liquid is water (density: p), the other is an unknown liquid that has a specific gravity of 0.63 (density: p'). The pressure in the lower center (P₁) is 100,000 Pa, what is the pressure (in Pa) at the higher center (P₂) if H = 3 m, H₁ = 6 m and H₂ = 8 m? Assume temperature = 15 °C, specific weight of water: 9800 N/m³. P1| O 52060 Pa O 63436 Pa O 46123 Pa O 32459 Pa H H ₂ H (P₂ ·P p'
A manometer consists of a tube of 0.5 inch in the inner diameter and an amount of mercury (SG Hg =13.55). On one side of the tube, oil (SG=1.4) was trapped, a bubble formed, and the fluid inside was stationary. The volume of the oil was 0.6 in^3 and the volume of the air was 0.2 in^3. Now, the oil and bubble are removed. The pressure change across the air bubble is negligible and any curvature on the bubble surface can be neglected in calculating the volumes. Determine how much the mercury height rises (i.e. h 4 -h 2 ).