Question 3 a. For the pressure vessel containing glycerin, with piezometer attached as shown, what is the pressure at point A? s.g=1.26 Open to atmosphere 40.8 cm Glycerin - b. Elaborating on the minor energy losses in pipes c. What are the factors influencing the frictional loss in pipe flow? d. Discuss dimensional homogeneity.

Question 3 a. For the pressure vessel containing glycerin, with piezometer attached as shown, what is the pressure at point A? s.g=1.26 Open to atmosphere 40.8 cm Glycerin - b. Elaborating on the minor energy losses in pipes c. What are the factors influencing the frictional loss in pipe flow? d. Discuss dimensional homogeneity.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

On a single plot, show curves that show the relationship between the pressure generated by thepump as a function of flow rate of water at 20 °C through the three branches of the piping systemshown below (delta P on the y axis and flow rate on the x axis; therange of the pressure should be 0 to ~1 MPa). Pipe inner diameter: 0.03 mPipe material: copperTypical mass flow rate of interest: 0.5 kg/sIgnore minor losses of tee's at points A and B and any features of branch 3Consider minor losses of two 90° elbows in branch 2
CS) Flow through a heat exchanger tube is to be studied by means of a 1/10 scale model. If the tmateaangeraarmall, carries widecreme de ratio of pressure losses between the model and the prototype if water is used in the model.
Take the density and dynamics viscosity of the water as follows, determine the value of friction factor (f), head loss (h1), pressure drop (dP) and power required to overcome the pressure drop (W) for the cases as shown in the table that follows. Take p= 1000 kg/m³ while u = 1.138 x 103kg/ms. Q2 Cases Pipe Material Water Velocity Pipe Diameter Pipe Length (m/s) (mm) (m) 1 Wrought iron 3.00 35 1000 2 Commercial steel 2.50 10 500
) where AP is the static The Hagen-Poiseuille equation for the laminar flow through a circular pipe is: AP pressure drop measured over some length of pipe, L. Use the Hagen-Poiseuille equation and the Darcy-Weisbach equation to derive an expression for the fanning friction factor, f, for laminar flow through a circular pipe where Re is the Reynolds number. Choose one answer from the list below: of= of O None of the above 32 Re 16 Re O f = 64 Re = o f = 32μLc 3 d² 8 Re O f = 16 Re
Dimensional Analysis and Hydraulic Similitude (fluid mechanics) 1. Water at 60F at 12 ft/s in a 6-in. pipe. (a) For dynamic similarity, determine the velocity of medium fuel oil at 90F flowing in a 12-in. pipe. (b) Determine the diameter of the pipe that should be used if a medium lubricating oil at 70oF if flowing at a velocity of 50 ft/s. find the: a. velocity : ____________________ fps b. diameter : ____________________ in.
C1 (a). A lubricating oil having the dynamic viscosity of 0.058 poise and kinematic viscosity of 0.19 stokes. Calculate ) the density of oil in kg/m³, (ii) the weight density of oil in N/m3,(iii) the specific gravity, and (iv) the specific volume in m3/kg. C1 (b). Calculate the capillary effect in mm in a glass tube of 4.4 mm diameter, when immersed in (1) water (2) mercury. The values of surface tension in contact with air are 0.0756 N/m and 0.74 N/m respectively. The contact angle for water =0° and mercury = 130°. ( (Enter only the values by referring to the unit given. Also, upload the handwritten answers in the link provided) C1(a).(1).The density of oil in kg/m3 C1(a). (ii) the weight density of oil in N/m3 C1(a). (iii) the specific gravity C1(a). (iv) the specific volume in m?/kg C1 (b). 1.The capillary effect (water) in mm ----- C1 (b). 2.The capillary effect (mercury) in mm
1. The deformation of the fluid will continue as long as the 2. When designing gates, vessels, dams or other bodies that are submerged in a liquid, it is important not only to estimate the - 3. The surface tension is the tensile force per -- in any direction along the surface the surface tension. 4. The value of - specifies whether the fluid can be assumed compressible or incompressible. 5. Archimedes' principle indicates- 6. A truck is filled with gasoline. If the container (tank) on the truck undergoes a - - is applied. - but also to specify its location on the body. then the liquid surface will begin to rotate clockwise about the center of the container and will eventually maintain a fixed tilted position.
On a single plot, plot three curves that show the relationship between the pressure generated by thepump as a function of flow rate of water at 20 °C through the three branches of the piping systemshown below. Delta P on y axis and flow rate on the x axis. The pressure range is 0 to 1 MPa. (Branches 1 and 3 are in the same plane; branch 2 is located 5 m above the other two branches. Pipe inner diameter: 0.0254 mPipe material: copperTypical mass flow rate of interest: 0.5 kg/sIgnore minor losses of tee's at points A and B and any features of branch 3Consider minor losses of two 90° elbows in branch 2
Plot curves on a single plot that display the relationship between the pressure generated by thepump as a function of flow rate of water at 20 °C through the three branches of the piping systemshown below (delta P on the y axis and flow rate on the x axis; therange of the pressure as 0 to ~1 MPa). Pipe inner diameter: 0.0254 mPipe material: copperTypical mass flow rate of interest: 0.5 kg/sIgnore minor losses of tee's at points A and B and any features of branch 3Consider minor losses of two 90° elbows in branch 2
The laminar flow of a fluid with a constant viscosity, 4, inside a channel is governed by the following boundary value problem (strong form): d'u dp for y E (0, h) "dy dr u = 0 at y = 0 and y = h vhere u is the fluid velocity and is the pressure drop in the direction of the flow. a) Derive the weak form of the boundary value problem described above.
Ql:- A 80 mm diameter of pipes and 300 mm long slides by its own weight of 1.7 kN inside a large cylinder of 80.2 diameter. The clearance between the eylinder and pipe is filled with oil of 5 stokes viscosity and s.g 0.92, find the velocity of sliding the pipe.
a 4 Exercise 7 -Opening and closing a boiler door for b) Calculate retracting speed, retracting time, travel speed ratio and travel time ratio. ictin Characteristic data required for calculation: Piston surface area: Ap = 2.0 sq. cm Piston ring surface area: APR = 1.2 sq. cm Stroke length: = 200 mm S Pump delivery rate: = 2 l/min b Retracting speed Retracting time Travel speed ratio Travel time ratio