Question 2a) Briefly explain the de chopper, inverter, controlled rectifier and ac voltage controller.b) A buck-boost regulator as shown in Figure 2 has an input voltage, Vs = 12 V. The dutycycle, k = 0.35 and the switching frequency is 30 kHz. It also has an inductance,L = 200 µH, filter capacitance, C = 440 µF. The average load current, Ia 1.25 A.Determine the:i.average output voltage, Va,ii.peak-to-peak output ripple voltage, AVc,iii.peak-to-peak output ripple current of inductor, AI,iv.peak current of the transistor, Ip,V.critical values of L and C, andvi.critical values of L and C if Vs is increased to 14 V. Estimate the change inpercentage for the critical values of L and C.isVsCLoadVo, VsVCi, IaFigure 2

Question 2 a) Briefly explain the de chopper, inverter, controlled rectifier and ac voltage controller. b) A buck-boost regulator as shown in Figure 2 has an input voltage, Vs 12 V. The duty cycle, k = 0.35 and the switching frequency is 30 kHz. It also has an inductance, L = 200 µH, filter capacitance, C 440 µF. The average load current, la 1.25 A. Determine the: %3D i. average output voltage, Va, ii. peak-to-peak output ripple voltage, AVc, iii. peak-to-peak output ripple current of inductor, AI,

Question 2 a) Briefly explain the de chopper, inverter, controlled rectifier and ac voltage controller. b) A buck-boost regulator as shown in Figure 2 has an input voltage, Vs 12 V. The duty cycle, k = 0.35 and the switching frequency is 30 kHz. It also has an inductance, L = 200 µH, filter capacitance, C 440 µF. The average load current, la 1.25 A. Determine the: %3D i. average output voltage, Va, ii. peak-to-peak output ripple voltage, AVc, iii. peak-to-peak output ripple current of inductor, AI,

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A fully controlled, single-phase bridge rectifier is powered from an ideal 220V, 50Hz source. The rectifier is triggered with a trigger angle of 60 degrees and provides a smooth current of 50A to the load at the output. According to this: a) Draw the waveform of the output voltage in scale and calculate the average value of the output voltage. Combine the average voltage signal with the output voltage wave signal. Show on the same figure. b) Draw the waveforms of the thyristor currents, the gap diode current and the current drawn from the source in scale. c) Calculate the value of the filter inductance used at the output when the ripple in the load current is 3A. (Do the operations by showing the output voltage shapes and areas on the figure. The answers should be in the system and order in the solved examples.)
Análisis de rectificador onda completa Consider the capacitor-filter rectifier circuit as shown in Figure 1. The input is a single-phase source that is derived from a 220 Vrms mains. Tasks for analysis: (a) Rig up the circuit as shown in Figure land plot V andi versus time. (b) Why is there ringing on the current wave-form? (c) What is the series impedance of the circuitệ (d) Plot V and V. versus time. What is the ripple? How does ripple depend on load, capacitor C; and frequency of input wave-form? (e) Measure the current and voltage waveform across the rectifier diode. (f) Estimate the average and ms currents through the rectifier diode, Calculate the diode power dissipation. (g) What should be the peak current rating of the diode? (h) Change the initial charge voltage on the capacitor Cr. What is the effect on the input surge current? (i) Change the phase angle of the input V, at start up. Observe the effect on current i. What happens and why? 1) Under whaf conditions do you get…
A single phase, fully controlled bridge rectifier supplies a series connected resistor- inductor load (R = 20, L = 0.02H) from 220V, 50HZ AC supply. The triggering angle of the thyristors is 60°. (Assume the circuit is ideal.) a. Sketch the circuit. b. Develop the load current expression and check the continuity of the load current. c. Sketch the load voltage and load current waveforms. d. Calculate the mean values of the load voltage and load current. e. Sketch the inductor voltage and calculate its mean value. f. Calculate the FF (form factor) and RF (ripple factor) of the load voltage.
A R-load half-wave rectifier used sinusoidal voltage source with a peak value (35.353kV). The firing angle is (30). The total resistance is 50k2 and frequency is 50HZ. Calculate (in details): load direct voltage, maximum direct voltage, normalized voltage and effective voltage, power delivered to the load, power factor, form factor, ripple factor?
Determine the ripple factor for the filtered bridge rectifier with a load as indicated in the figure below.
Draw the circuit diagram with shape of signal after transformer, after bridge rectifier, with capacitor and with voltage regulator.
For a Full wave rectifier circuit, the AC voltage input to transformer primary is 115V. Transformer secondary voltage is 50V. Load resistor is 25 ohms. Determine Peak and Average DC Component of load voltage. (Assume ideal diodes) a.VDC (peak) = 25.4 V; VDC (average) = 18.5V b.VDC (peak) = 35.4 V; VDC (average) = 22.5V c.VDC (peak) = 38.4 V; VDC (average) = 23.5V d.VDC (peak) = 50 V; VDC (average) = 34.5V
In the operation of a half-wave rectifier with a capacitor-input filter, the ripple factor can be lowered by ……….the value of the filter capacitor or …………..the load resistors.
A load is connected in the Full Bridge rectifier circuit (Four Diodes). Usedtransformer primary voltage value is 220 V (rms). The transformer winding ratio is 1:10.Using the 0.7 V model of the diode,Load Rating: 7 K Ohmsa) How many % of conduction does each diode branch stay on?b) Find the average values of the load voltage.c) Find the average values of the load current.d) Find the effective value of the load voltage.e) Find the effective value of the load current.
QUESTION 2.. A load is connected in the Full Bridge rectifier circuit (Four Diodes). Usedtransformer primary voltage value is 220 V (rms). The transformer winding ratio is 1:10.Using the 0.7 V model of the diode,Load Rating: 7K OHM d) Find the effective value of the load voltage.e) Find the effective value of the load current.
Derive the average and RMS output voltage for three phase half controlled rectifier with RLE Load or three phase semi converters.
the three phase half wave uncontrolled rectifier is operated from 500v,50Hz supply at secondary side and the load resistance is 25 ohms. if the source inductance is negligible, determine a) rectification efficiency b) form factor c) ripple factor d) transformer utilization factor e) peak inverse voltage of each diode