Question 1 In this problem, you are required to design a 30-channel FDM multiplex for the transmission of voice signals. There are two bands available with the following frequency ranges: Band 1: 50 kHz - 80 kHz Band 2: 200 kHz - 230 kHz It is also required to have a 2 kHz guard band (no guard band is required is the beginning, i.e., before the first user) between each adjacent signal to avoid signal interference (for band 1). For band 2, 3 kHz guard band is required between each adjacent signal to avoid signal interference (no guard band is required is the beginning, i.e., before the first user). Draw a clear block diagram of your 30-channel. The diagram must show the number of stages of the multiplexer, the starting and the terminal frequency of each stage, the frequency of each guard band in each band, and the frequency of each user in each band (refer to last slide of chapter 4c pdf file). You should also describe the details of your design to get full credit.

Question 1 In this problem, you are required to design a 30-channel FDM multiplex for the transmission of voice signals. There are two bands available with the following frequency ranges: Band 1: 50 kHz - 80 kHz Band 2: 200 kHz - 230 kHz It is also required to have a 2 kHz guard band (no guard band is required is the beginning, i.e., before the first user) between each adjacent signal to avoid signal interference (for band 1). For band 2, 3 kHz guard band is required between each adjacent signal to avoid signal interference (no guard band is required is the beginning, i.e., before the first user). Draw a clear block diagram of your 30-channel. The diagram must show the number of stages of the multiplexer, the starting and the terminal frequency of each stage, the frequency of each guard band in each band, and the frequency of each user in each band (refer to last slide of chapter 4c pdf file). You should also describe the details of your design to get full credit.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

plot the digital signals 1-101010011 2-111001100 using 1-on-off(Rz) 2-polar(RZ) 3-bipolar (RZ) 4-on-off(NRZ) 5-polar (NRZ)
All of the following statements about the SCR could be true except: O A. SCRS are suitable for high frequency (over 100k) switching applications O B. SCRS are largely used for power application at the line frequency O C. None of the other choices is the correct answer O D. SCRs are not used in automotive applications O E. SCRs can be used in household appliances
Q2: Fill in the hlanks for the following (14 marks) 1-There are three types of AM modulation: 2- The indirect FM method convert the 3- The bandwidth of FM modulation Can be divided into two types And to and
4) Rebuild the following instructions 1. MOV AX, 0000H 2. MOV AL, FFH 3. NOT BL 4. NEG CX
Type your question here The B.w in DSB-sc equal to 2Wm but before modulation was wm , we Know the BW meney [ecenemic ] , why we use modulation?
Question 555 A 10 mW signal travels over three links. The first link causes the signal to lose one fifth of its power. The second link amplifies the signal by a rate equivalent to 6 dB. The third link causes the signal to lose 30% of its power. What is the power of the signal in mW at the end of the third link? Please show work in detail.
C What are the Q- point values of IC,VCE? 70A 50A 40A 30A 2 20A 10A Va(V) 02(Anvwer os -d.
Q: for the fmowing function xcnJ=4** if X]=16, Se the Vatue f A ir---- O a. 2 O b. 1.5 O c.4 O d. 8 O e. None of the options
You need to produce a square wave with a low voltage of 0.500 volts and a high voltage of 2.500 volts. The DAC is 12 bits with a Vref of 3.3 volts. What is the input code for the low voltage and the high voltage? Low: 601, High 3003 Low: 621, High: 3103 Low: 591, High: 2903 Low: 621, High: 2103 3 O O O O
Consider a 1 into 4 de-multiplexer.The data input and selection line waveforms for the demultiplexer are given below. Draw the corresponding output waveforms (for D0 to D3). Data in SO DO D3 Note: You need to draw the waveforms on paper. Take the photo and then upload. A- B I
SNR is defined as a ratio of O noise power to samplng-ffequency signal power to noise powér signal power to signal BW O noíse power to signal power
mon De-emphasis is done: Select one: O a. none of the answers O b. after FM demodulation OC before FM demodulation O d. before FM modulation