question 1 LAB 2.pdfAssignment1.pdfEEB434 Tutorial.pdfE *Assignment 2 (2021).pdfadvanced-mathematical-techO FileC:/Users/Kelekwe/Downloads/Assignment%202%20(2021).pdf...CD Page view A Read aloudO Add textV Draw- HighlightO Erase2of 2QUES.1 Two air-cored coils are disposed relatively to each other sothat 75% of the flux in one coil links all the turns of the other coil. Eachcoil has a cross-sectional mean diameter of 2cm and a length of 50 cm.If there are 2000 turns of wire on one coil, calculate the number of turnsrequired on the other coil to give a mutual inductance of 20 mH.QUES. 2 Two identical 900 turn coils A and B lie in parallel plane. Acurrent changing at the rate of 2500 A/s in A induces an emf of 20 V inВ.(a)Calculate the mutual inductance of the arrangementIf the inductance of each coil is 25mH, calculate the fluxproduced in coil A per ampere and, the percentage of this fluxwhich links the turns of B(c) Percentage of this flux which links the turns of BQUES. 3 A flux of 0.5 milli-Weber (mWb) is produced by a coil of900 turns on a ring with a current of 3 A in it. Calculate:The inductance of the coil(b) e.m.f. induced in the coil when a current of 5 A is switched off,assuming the current to fall to zero in 1 millisecond4:46 PMO Type here to search27°C Light rain11/25/2021

Note :- Student mentioned to solve only Q1. (1) Given, Two air - cored coils are placed…

QUES.1 Two air-cored coils are disposed relatively to each other so that 75% of the flux in one coil links all the turns of the other coil. Each coil has a cross-sectional mean diameter of 2cm and a length of 50 cm. If there are 2000 turns of wire on one coil, calculate the number of turns required on the other coil to give a mutual inductance of 20 mH.

QUES.1 Two air-cored coils are disposed relatively to each other so that 75% of the flux in one coil links all the turns of the other coil. Each coil has a cross-sectional mean diameter of 2cm and a length of 50 cm. If there are 2000 turns of wire on one coil, calculate the number of turns required on the other coil to give a mutual inductance of 20 mH.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter7: Symmetrical Faults

Section: Chapter Questions

Problem 7.21MCQ

See similar textbooks

Similar questions

For Fixed Bias Configuration Solve for Ib, Ic and le. Atleast 2 decimal place. Be mindful of units. Assume Ic is not equal to le. ... 4 RC 15002 RB VCC 20V 90A/A 100k2 Ib=Blank 1 HA Ic=Blank 2mA le=Blank 3 mA Blank 1 Add your answer Blank 2 Add your answer Blank 3 Add your answer
Question 15 In half wave rectifier with filter, if the capacitance is increased, the ripple factor increases. True False Moving to another question will save this response. ip
Damping ratio quettion.
In half wave rectifier with filter, if the capacitance is increased, the ripple factor increases. True or false
A 120 Vp is applied to the primary coil of a center-tap transformer of turn ratio (n1 : n2 = 6: 2) . If the secondary coils are connected to a Ge diodes center-tap full wave rectifier, the output DC voltage is about __________. *1- 13.42 V2- 14.15 V3- 15.58 V4-12.54 V5- 16.23 V
e+ VBB = 12Y. 50k VE RBB- 5Kd 7= 0.6 ATEM F 50052 Ip= 1OUA. GND DETERMINE: A) RB1 B) RB2 C) Vp D) VR2, DURING THE CHARGING PHASE E) VR2, DURING THE DISCHARGING PHASE.
what is the use of DC/DC tension converter DC/DC booster MT3608
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) D IN4001 R 10 kn IN4001
Write the answers precisely, do not elaborate unnecessarily, and don't use chatgpt, if i caught it I'm gonna downvote Question: Discuss the electrochemical techniques that are useful to study the capacitive properties of a material. Highlight the importance of each technique
ssignment_2 5 Immersive Reader O Open in Deskt (b) Connected in paralld. 7) The following readings are obtained in the measurement of an inductor: 1.003,0.998, 1.001, 0.991, 1.009, 0.986, 1.005,0.997, 1.008, and 0.994 µH. Determine the (a) Arithmetic mean. (b) Average deviation. (c) Standard deviation.
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across Ri, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) IN4001 Ry OV 10k) D IN4001
44. What type of electrical component has this a graph for its IV curve? And which Letter marks its forward conduction turn on point. E A