Q/Complete the dam section dimensions and then find the moment of allconsidered forces about the toe? Take C=0.6,325 KN/m, S̟ = 2.4, H = 9 m. H-78KNY. = 10-, Y, =%3D%3D%3DH, = 2a/5, – CF.bHiWw1Fsh2FsysPEWw3FsvW2FshWwa/FshWib=9 mC. Yw.H'C. Yw.HTusCY,H' + (C. Yw. H – C. Yw. H')

Given: Yw= 10kN /m^3 Yc = 25kN/m^3 Ss = 2.4 C = 0.6 H = 78

Q/Complete the dam section dimensions and then find the moment of all considered forces about the toe? Take C=0.6, KN 3. 10-4 Y 25 KN/m, S = 2.4, H = 9 m. H=78 %3D %3D %3D 31 H, = 2a/5,- c %3D F.b Hi Fsv Wwi Fsh2 Fsys PE Ww3 Fsv W2 Fsh Wway Fsh, W, Wi b=9 m C. Yw.H' C. Yw.H CY,H' + (C. Yw. H - C. Yw. H')

Q/Complete the dam section dimensions and then find the moment of all considered forces about the toe? Take C=0.6, KN 3. 10-4 Y 25 KN/m, S = 2.4, H = 9 m. H=78 %3D %3D %3D 31 H, = 2a/5,- c %3D F.b Hi Fsv Wwi Fsh2 Fsys PE Ww3 Fsv W2 Fsh Wway Fsh, W, Wi b=9 m C. Yw.H' C. Yw.H CY,H' + (C. Yw. H - C. Yw. H')

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the maxi mum shear stress deue loped in the beam 5 KN/m Ø4 cm Ø3 cm 3 N/m 0.2 m 0-2m 0.2
Draw axial,shear force and bending miment digram fig 1and 2 10 ANm 20 AN | 20 k 1.5 m 1.5 m Figure (1) 70 kN 70 kN -20 kN/m 25 m 2.5 m 2.5 m Figure (2)
For the portal frame shown in the given figure, the shear equation is B 4 m (a) (b) (c) (d) P MBC + MCB 4 4 m MBA + MAB. 4 MCD 4 MATT El MBA+MAB + P = 0 4 + P = 0 + Constant 4 m hinge +P=0 C MCD 4 LID mim + P = 0
2. Determine the spacing of vertical stirrups near the left support of the beam loaded as shown in Flgure 1. Given the following. Wa = 20 kN/m WL = 28 kN/m bw = 290 mm f'c 24 MPa Pa 80 kN d = 560 mm fyt = 275 MPa P, = 110 kN Pa, Pt Wa, Wi 0.5m 2.5m bw
The load shared by the member BC of the structure shown in figure below is D (a) 2√√3kN (c) 4 kN 30% ↓2 KN B (b) 3√2kN (d) 3 kN
Determine the Internal Forces at ALBLGHFGAB in Kn
B. Work on the following problems. Indicate first under which case it belongs to and then solve completely. 1. Plate AB has a width of 1.5 m and a radius of 3 m. Determine the horizontal and 3 m vertical components of reaction at the pin A and the vertical reaction at the smooth stop B due to the water pressure. (Av = 0, AH= 66.218 kN–, RB = 104.014KN|)
Draw the deformation shape H.W 18KN/m 40KN B 1.5 4m 3m Fig.(3) B 100 kN 3m 1. 2m- 3 m El = comstant
4- Is this a safe beam under the action of 120 kN.m moment? d= 55cm, bw-32cm, n=15. C25: Allowable stress=10 MPa S420: Allowable stress=220 MPa 4Ф 14 O 000 Modulus of rupture-2.3 N/mm?
1. Given the values of the load L and FR-R-R dimension R, for what value of the couple M will the force in link CH be equal to 10 kN, compressive? Note that R = 2m andL = 50 kN. в м 2R- Given: (figure); R = 2m, L = 50kN Required: M so that FCH %3D 10 kN, C 7,
12 KN Q 1 find stress Rod Rod D TCD ТАВ AB CD beam 10 m A uniform beam supported by two beam have cross sectional area 25 for AB and 12 for CD determine position d
The channel section carries a uniformly distributed load totaling 6W and two concentrated loads of magnitude W. Determine the (a) location of the neutral axis from the bottom, (b) the moment of inertia about that axis, (c) the maximum allowable value for W if the working stress are 4.0 MPa in tension, 8.0 MPa in compression, and 2.4 MPa in shear. 20 mm ←140 mm → 20 mm 6W (total) W 4 m 20 mm A 1.0 m/ O B 41.01 W 140 mm ΝΑ