Q4) During blood transfusion, suppose a container was placed 60 cm above the patient's arm with venous blood pressure of 3 mmHg as shown. If the density of blood is 1040 kg/m³, what is the net pressure acting to transfer the blood into the vein? What fraction of the atmospheric pressure would it be? What will happen to the net pressure if the distance between the blood container and the patient's arm is doubled. 140 Blood Transfusion 600 2015 Figure (Q) - Umm²) 0.006 0010 Figure (Q3) Stran 1/4

Q4) During blood transfusion, suppose a container was placed 60 cm above the patient's arm with venous blood pressure of 3 mmHg as shown. If the density of blood is 1040 kg/m³, what is the net pressure acting to transfer the blood into the vein? What fraction of the atmospheric pressure would it be? What will happen to the net pressure if the distance between the blood container and the patient's arm is doubled. 140 Blood Transfusion 600 2015 Figure (Q) - Umm²) 0.006 0010 Figure (Q3) Stran 1/4

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter7: Length And Length-related Variables In Engineering

Section: Chapter Questions

Problem 15P

See similar textbooks

Similar questions

Fluid is being given to a patient by an IV in a vein of their arm. The fluid is a saline solution with a density of 1005 kg/m³. The fluid enters the vein through a 20-gauge needle with an inside diameter of 0.603 mm. The surface of the saline in the bag is 0.60 m above the end of the needle and the pressure at this surface is atmospheric. The gauge pressure in the patient's vein is 10 mm Hg. A. What would be the flow rate (in mL/min) of saline solution into the vein if there were no losses of mechanical energy in this process? B. Given that the actual flow rate is 5.0 mL/min, what are the frictional energy losses in J/kg? vein gauge P needle atm saline IV fluid = 10 mm Hg
Q3: A pitot-static tube is used to measure the flow velocity of turpentine flowing in a pipeline if the manometer reading is 8 cm of mercury, calculate the average velocity, pressure drop, and volumetric flow rate at that point in the pipe line. Also evaluate Reynold number for turpentine and which type of flow in the pipe. Ph J Re Density of turpentine is 850 kg/m³, density of mercury is 13600 kg/m³, cv = 1, D=10 cm, turpentine 0.001375 and 0 = 45°. =
A steady push on the piston in a syringe is shown in the figure causes a flow rate of 0.4 ml/sec. The fluid has a mass density of 900 kg/cum and an absolute viscosity of 0.002 Pa-sec. Assume that there is no headloss in the larger cylinder. Determine the reynolds number for the given flow of 0.4 ml/sec in he needle. 645 917 897 795 Determine the headloss in the needle 18.90 m 15.21 m 14.43 m 16.23 m Determine the force required to maintain the flow 64.23 kn 45.25 kn 34.77 kn 25.36 kn
Q3: A tube has a u-shaped, as in the following figure, if the density of water is 997 kg / m3, the concentration point of mercury is 13550 kg / m3, find the height of the fluid (h )shown in the diagram and the amount of pressure (P) at point a, b, d, and c? Water- |0.3m Mercury
Gas flows at a steady rate in a 100-mm diameter pipe that enlarges to a 150- mm diameter pipe. At a certain section of the 100-mm pipe the density of the gas is 200 kg/m³ and the velocity is 20 m/s. At a certain section of the 150- mm pipe the velocity is 14 m/s. Which nearly gives the weight flow rate in N/s in the pipe? O a. 412.5 N/s O b. 125.7 N/s 331.1 N/s O d. 308.2 N/s
Question 12 of 25 If a depth of fluid of 1 m causes a pressure of 7 kPa, what is the specific gravity of the fluid? Select the correct response: 0.795 0.828 0.632 0.646 0.714
1. The reading of an automobile fuel gage is proportional to the gage pressure at the bottom of the tank. The tank is A deep and is contaminated with B of water. The specific volume of gasoline is 0.00147076 m /kg and that of air is 0.0008313 m³/kg. Unit weight of water is 9790 N/m3 a. Determine the gage reading when the tank is full of gasoline b. How many cm of air remains at the top when the gage indicates full if the tank is A deep and is contaminated with B of water. c. Determine the pressure at the interface of the gasoline and water when the gage indicates full A = First name in inches Vent B = A/10 in inches Air h A Gasoline Pgage Water B
Q-3 Three different liquids with properties as indicated fill the tank and manometer tubes as shown in Fig. Determine the specific gravity of Fluid 3. Fluid 1: specific weight = 62.4 Ibit Fluid 21 density - 1.60 slugs/t Fluid 3: specific gravity =? Fluid 2 7 ft 6 ft Fluid 1 Fluid 3 5ft 3 ft
A mercury manometer is connected to a flow meter in a pipeline. The gaugepressure at Point 1 is 38 kN/m2 and at Point 2 the vacuum pressure is −50 kN/m2. The fluid in the pipeline is water. Calculate the manometer reading Rp .
A pipe contains an oil sp.gr. 0.80. A differential manometer connected at the two points A and B of the pipe shows a difference of mercury as 20 cm. Find the difference of pressure between the two points
A closed tank is filled with oil and water with the given situation as shown in the figure. An orifice with an unknown diameter is placed 1 m from the bottom of the tank discharging 10 L/s based on a calibration test. The jet from the orifice hits the ground 3.8 m horizontally away from the vena contracta. If the coefficient of discharge is 0.64, determine: a. The diameter of the orifice. b. The coefficient of contraction. Air p = 16 KPa 1 m S = 0.82 3.80 m Water 1 m 2 m 1 m
A closed tank is filled with oil and water with the given situation as shown in the figure. An orifice with an unknown diameter is placed 1 m from the bottom of the tank discharging 10 L/s based on a calibration test. The jet from the orifice hits the ground 3.8 m horizontally away from the vena contracta. If the coefficient of discharge is 0.64, determine: a. The diameter of the orifice b. The coefficient of cotraction. Air p- 16 KPa 1 m S0.82 3.80 m Water 1m 2 m 1m