Q2. Determine the magnitude and direction of friction torce acting on the 20kN block shown if P-10kN ,the coefficient of static friction is 0.25 ,the forces are applied with the block initially at rest 30° W=20kN 10kN TITT U=0.25

Q2. Determine the magnitude and direction of friction torce acting on the 20kN block shown if P-10kN ,the coefficient of static friction is 0.25 ,the forces are applied with the block initially at rest 30° W=20kN 10kN TITT U=0.25

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.63P: The leather rein used to fasten the horse to the hitching rail weighs 3.5 oz per foot. The...

See similar textbooks

Related questions

Q: Two meshing spur gears with a diametral pitch of 4 teeth per inch and a pressure angle of 20 degrees…

Q: ● Determine the moments and products of inertia of the bent rod shown (composed of three slender…

A: The moments and products of inertia are quantities used to describe the distribution of mass in an…

Q: 3. The rigid body shown below can be represented by a thin circular disk with a square hole in its…

A: According to the given data The density of the material=0.03028slugs/in3 The thickness of…

Q: A reversed Carnot cycle required 3 hp and extracts energy from a lake to heat a house. If the house…

A: According to the given data Q=2000Btu/lbm W=3hp=127.226 Btu/min { 1hp=42.408btu/lbm}…

Q: Send correct answer

A: To convert world energy consumption from quadrillion Btus to the equivalent quantities in other…

Q: a. What is P0741 the diagnostic trouble code (DTC) for? b. What transmission system component sets…

A: P0741 the diagnostic trouble code (DTC)

Q: Find the coordinates of the centroid of the shaded figure below.

Q: A particle P of mass m = 2 kg arrives at point O with a horizontal velocity and starts rolling down…

A: Since you have posted a question with multiple sub-parts, we will solve the first three subparts for…

Q: A small block of mass m slides frictionlessly in the given orbit. Calculate the magnitude of the…

A: According to the given data m=1kg g=10m/s2 We need to find Resultant forces the block at C

Q: The shaft shown in the figure is machined from AISI 1040 CD steel. The shaft rotates at 1600 rpm and…

A: Shaft speed, N=1600 rpmApplied forces, F1=1600lbfF2=640 lbfTorque, T=1600 lbf·inMinimum Shaft…

Q: A 15,500 kg jet plane takes off from an aircraft carrier with the help of a catapult (see figure a).…

Q: Make a copy of the isothermal transformation diagram for an iron-carbon alloy of eutectoid…

Q: Q1/ Compare between the following: 1- Swirl and crevice flow motions. 2-S.I and C.I fuel injectors.…

A: Crevice flow and swirl flow are two different types of fluid motion in various contexts. Here is an…

Q: A rope of length L = 2.2 m and mass m = 5 kg is initially at rest and can slide on an inclined surf…

A: It is asked to calculate the work done by friction as a function of y

Q: 1. The Resultant of the concurrent forces in the figure below is 300kN, pointing up along the…

A: Since, unit of Resultant force is kN, hence I consider unit in this problem to be kN. If unit is N,…

Q: 3. A homogeneous thin quarter circular plate with 0.20 m radius has a mass of 1.2 kg. Which of the…

A: The mass of quarter circular plate is 1.2 kg.

Q: )The force measured at points A, B, and C are 80KN, 200kN and 190kN, respectively Taking the nose…

Q: Blocks A and B have weights of 100 lb and 200 lb, respectively, and are moving initially with the…

A: The weight of the block A, (WA)=100 lb The weight of the block B, (WB)=200 lb The initial velocity…

Q: Hi, I am still not sure I am understanding this correctly. The hoverboard is moving in the same…

A: Given Data

Q: Determine the absolute maximum bending moment in the W250X115 beam. The beam is made from A36…

Q: FIND THE REACTIONS 20k IIK 'I' 8' 17¹ N 25k

Q: A water pipe is buried 0.37 m (cf. Problem 4.12) below ground in wet soil (a = 7.75 x 10-7 m²/s and…

A: The thermal conductivity is k=2.59 W/mK The thermal diffusivity is α=7.75×10-7 m2/s The initial…

Q: A turbocharged, 4 cylinders and 2 liters engine operates with stoichiometric gasoline, 2000 rpm, and…

A: please refer handwritten solution

Q: Problem 24.2 The system is at rest in the position shown, with the 10 kg collar A resting on the…

Q: modulus of elasticity

A: in the question original length is not given. With original length of the specimen not possible to…

Q: What should be the percent increase of COP of a standard vapor compression refrigeration system when…

Q: Assume that P(s) indicates paralysis in the equation given below and that U(s) is the percentage of…

A: Given: PsUs=7.63×10-2s2+1.15s+0.28 To find: Damping ratio and natural frequency Percentage…

Q: How long does it take a 750- W coffeepot to bring to a boil 0.56 L of water initially at 9.6 ∘C ?…

A: According to the givn data Power, P = 750 W mass of water, m = 0.56 L =0.56x10-3m3 mass of aluminum,…

Q: A certain two dimensional shape has the following integrals f dA = 4.5 in² fx dA fyd A S x² dA 13.5…

Q: The double-reduction helical gearset shown in the figure is driven through shaft a at a speed of 780…

A: Given-Information: Speed , N = 780 rev/minN2 = 14N3=48N4=16N5=34 To-Determine: Output torque on gear…

Q: 0.2 m 0.25 m 0.2m 06m Knowing that at the instant shown the angular velocity of rod AB is 15 rad/s…

A: As per Bartleby answering guidelines, one question can be answered if multiple questions are posted.…

Q: The rectangular plate is subjected to the deformation shown by the dashed line. The dimensions are X…

A: According to the given data ∆y=4mm X=130mm We need to find Average shear strain in the plate

Q: A power plant condenser diverts from the power plant water that condenses heat at a rate of 34 [MW]…

A: The condenses heat rate is Q=34 MW The inlte temperature of cooling water is Ti=15°C The outlet…

Q: What are the 3-classification methods used in rapid prototyping (RP) processes? Also explain each in…

A: What are the 3-classification methods used in rapid prototyping (RP) processes?

Q: 3. Compute for the force at members BD, CD and DE of the Warren Truss Shown:

Q: The disk is subjected to a couple moment M. The end of the spring wraps around the periphery of the…

A: The spring constant is k=4 kN/m. The radius is r=0.6 m The moment applied is M=300 N-m.

Q: A rope of length L = 2m and mass m = 2.2 kg is initially at rest and can slide on an inclined…

Q: Find an expression for maximum to critical velocity for adiabatic flow of a perfect gas

A: The ratio of the maximum to the critical velocity for an adiabatic flow of a perfect gas can be…

Q: A part of a machine consists of two arms OA and AP so that the angle between OA and AP is always…

Q: A particle P of mass m = 3 kg arrives at point O with a horizontal velocity and starts rolling down…

A: Given: m=3 kgR=5 mk=60 N/m

Q: Pumps: A centrifugal pump having 4 stages in parallel, delivers 18 kiloliters/min of liquid…

Q: 11. Which is used to change only the direction of shafts in a machine? Zerol bevel Miter Both b and…

A: The correct option.

Q: Problem 25.1 Block A is released from rest at Point 1, where it is initially compressing the spring…

Q: he distributed load on the arch varies by q = (300N)cos(theta). Determine the resultant force and…

Q: d: Write down and explain the thermal efficiency formulas for the cycles explicitly. e: Discuss how…

A: (1) Diesel Cycle (2) Stirling Cycle (3) Brayton Cycle

Q: A tapered bar with a solid circular cross section is held rigidly at either end. As shown in Figure…

A: Given Data: A=0.03-x40 To Find: (a) Determine the strain shape function matrix. (b) Displacements…

Q: 10. Water flows from a lake as shown below at a rate of 5.0 ft³/s. Is the device inside the building…

Q: i have a question, please help The resultant describes the __________ of multiple ___________. The…

A: The question is given about addition of vector. We have fill the correct sequence.

Q: can u solve the question using newton or lanrnage method in detail with hand written notes

A: Free body diagram mx¨1+cx˙1+kx1-x2=0 Rearranging mx¨1+cx˙1+kx1=kX2sinωt

Q: Q15: A) FCC metals are often recommended for use at low temperatures, particularly when any sudden…

A: The FCC metals have the structure of face centered cubic. These metals are used at low temperatures…

Concept explainers

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.

Question

مييل

Q2. Determine the magnitude and direction of friction force acting on the 20kN block
shown if P-10kN ,the coefficient of static friction is 0.25 ,the forces are
applied with the block initially at rest
03
30°
W=20kN
10kN
μ=0.25

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: To find:

VIEW

Step 2: Calculate:

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Clutches, Brakes, Couplings and Flywheels

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The 600-lb cable spool is placed on a frictionless spindle that has been driven into the ground. If the force required to start the spool rotating is F = 160 lb, determine the coefficient of friction between the ground and the spool. Neglect the diameter of the spindle compared to the diameter of the spool.
3. Blocks A and B have a mass MA and MB, respectively. If the coefficient of static friction between A and B and between B and C is us and between the ropes and the pegs D andE µ's, determine the smallest force F needed to cause motion of block B. Given: E e = 45 deg Hs = 0.25 MA = 100 kg He's = 0.5 Mв 3 150 kg Р%3 30 N B m g = 9.81
Find the degree(s) of freedom and the type of constraint. Show using the principal of virtual work: m2 = γm1/2 where γ is the coefficient of friction.
The coefficient of static friction between the 50-kg crate and the ramp is μs = 0.35. The unstretched length of the spring is 800 mm, and the spring constant is k = 660 N/m. Determine the following: 1 The normal force acting on the crate is Blank 1 N. 2 The friction force acting on the crate is Blank 2 N. 3 The minimum value of x at which the crate can remain stationary on the ramp is Blank 3 mm.
2. The 100 – Ib force acts as shown on a 300 - Ib block placed on an inclined plane. The coefficients of friction between the block and the plane are us = 0.25 and Hk = 0.20. Determine whether the block is in equilibrium, and find the value of the friction for the friction force. 300 Ib 100 lb
r The bottle shown rests at a distance of r = 2.5 ft from the center of the horizontal platform. The coefficient of static friction between the bottle and the platform is μ = 0.25. The platform starts at rest, rad and then begins rotating at an accelerating rate of 0 = 0.8 $² Assuming the bottle doesn't tip over, after how many seconds does the bottle begin to slip? t = S
A chain having a length L and weight W rests on a street for which the coefficient of static friction is us. If a crane is used to hoist the chain, determine the force P it applies to the chain if the length of chain remaining on the ground begins to slip when the horizontal component is Px. What length of chain remains on the ground? Given: L = 20 ft W = 8lb/ft = 0.2 us= : 10 lb Px =
2. Find the least value of P required to cause the system of blocks to have impending motion to the left. The coefficient of friction is 0.2 under each block. 300 Ib 100 lb 30 °
The 500KN block shown is in contact with a 45°incline. The w coefficient of friction is 0.25. Determine the horizontal force P necessary to 1.Just start the block up the 45° incline 2.Just to prevent the motion down the incline. 3.lf P=400KN, what is the amount and direction of friction force?
An object with weight W is dragged along a horizontal plane by a force acting along a horizontal plane by a force acting along a rope attached to the object. If the rope makes an angle 0 with the plane, then the magnitude of the force is µW F = µ sin 0 + cos 0 where u is the coefficient of friction a. Find the rate of change of F wrt 0. b. The value of 0 at maximum or minimum value of F.
Q3 - Blocks A and B have a mass of 7 kg and 10 kg, respectively, and there are pulleys at C and D. Using the coefficients of static friction indicated, determine the following: 1- The smallest force P which can be applied to the cord that causes impending motion. 2- Does block B spill, flip over, or nothing happen? Prove that. 400 mm D B 500 mm HAB=0.1 A P HA=0.3 co
Q3 - Blocks A and B have a mass of 7 kg and 10 kg, respectively, and there are pulleys at C and D. Using the coefficients of static friction indicated, determine the following: 1- The smallest force P which can be applied to the cord that causes impending motion. 2- Does block B spill, flip over, or nothing happen? Prove that. 400 mm D B 500 mm HAB=0.1 A P M₁=0,3