Q2- Draw the influence lines for the vertical reactions at supports B and D, shear and bending moment at point C for the given continues beam shown in Figure 2. determine the maximum positive and negative shears and the maximum positive and negative bending moments at point C due to a concentrated live load of X₂ kN, a uniformly distributed live load of 2X₁ kN/m, and a uniformly distributed dead load of X₁ kN/m. A X1 = 100.8 2X1=201.6 X2= 549 -5 m- B -6 m- C Figure 2 -4 m- D H -3 m- E -4 m- F

Q2- Draw the influence lines for the vertical reactions at supports B and D, shear and bending moment at point C for the given continues beam shown in Figure 2. determine the maximum positive and negative shears and the maximum positive and negative bending moments at point C due to a concentrated live load of X₂ kN, a uniformly distributed live load of 2X₁ kN/m, and a uniformly distributed dead load of X₁ kN/m. A X1 = 100.8 2X1=201.6 X2= 549 -5 m- B -6 m- C Figure 2 -4 m- D H -3 m- E -4 m- F

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

QUESTION 3 If the allowable bending stresses for a beam in one application is 6 kip/in2 in tension. The cross-section of the beam is W8 x 40. If the beam is 10 foot long and simply supported and has a concentrated load applied at x = 3 ft as shown below. • Generate the shear force and bending moment diagram in terms of P; • Based on the allowable maximum bending moment you just obtained above, calculate/ input the mazimm allowable value of the load P: please, pay attention to units, and calculate your answer to 1 decimal place.. 3 ft 7 ft kip.
2. Note the loaded beam shown in figure 2. Point A is at x = 0 m, point B is at point x = 6 m, and point C is at x = 8 m. Note that there is an applied clockwise moment of 200 kN•m at point C. Derive the equations that describe shear (V) and bending moment (M) over the length of the loaded beam. Include free body diagrams of the sections for each distinct region of the beam. You do not need to draw the shear and bending moment diagrams. Just derive the equations. 20 KN/m 200 KN, m A B Figure 2
1- What are the reactions at A and B? 2-What is the maximum internal load? (Vmax and Mmax) 3- Draw the corresponding shear and bending moment.
Activity 3 A rig is to be constructed, which will consist of a 10m long elastic beam, simply supported at both ends, as shown in Figure 1. The first simply supported beam is subjected to the concentrated loads and the second beam is subjected to the distribution and point loads. Determine the distribution of shear force. Calculate the bending moments, due to bending in the simply supported beam. 500N 1000N 2000N 500N 2m Im lm lm Im 4m Figure 3: SSB with point loads 80 UDL: 10 (KNm) 2 (m) 7 (m) Figure 4: SSB with the combination of point and distribution load
IN-CLASS EX. 5-6 Draw the complete shearing force and bending moment diagrams for the beam. 800 N 1000 N 1200 N 100 mm 200 mm 50 150 mm A C E 250 mm Rg=600 N RD=2400 N 49
wo = 9 kN/m, L = 5.5 m, E = 220 GPa, and I = 100 x 10° mm4. A Part 1 Cut a cross-section through the beam at any point and draw a free body diagram to the right of your cut. Determine the internal bending moment M(x). The diagram shows M(x) in its positive direction. Your answer may be negative. Check your equation by solving for Mat x= 2.8 m. Wo M(x) L-x Answer: M(x = 2.8 m) = i kN-m
Please help me solve this problem by following these steps. Unsure of how to solve for this answer, please write clearly. Thanks in advance. •Step 1 –Calculate the end reactions •Step 2 -Develop the shear diagram •Step 3 –Determine the maximum shear (V) •Step 4 –Calculate the maximum moment (M) •Step 5 –Calculate required section modulus (Sx) ??=???x1.05 •Step 6 –Calculate required area (A) ?=3?2??x1.05 •Step 7 –Select the appropriate beam size: S4S, Rough Cut, or Glulam
Your answer is partially correct. For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let a=2.50 m, b=4.25 m, Pg= 45kN, and Pc = 90kN. Construct the shear- force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. Answers: Ay= a 74.189 B Calculate the reaction forces Ay and Dy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) Dy= i 59.21 B a PB a Pc KN Pc b KN D b D P x
Draw bending moment diagram for the loading shown in Figure Q15
Assignment 2 A Copper bar is loaded as shown complete the following: a. Draw a neat shear force and bending moment (Table of values is required) b. Calculate the maximum bending stress, clearly indicate where this occurs c. Calculate the maximum shear stress, clearly indicate where this occurs d. Plot the bending and shear stress for the cross section at x= 4 ft. from the left hand support. Clearly show the calculations were made at the following positions: y-0, 2, 4, 6, 8, 10 and 12 35 Ib/ft. 200 Ib Beam cross section 12 65" 8 ft. 5ft. 3 ft.
Part 1 For the simply supported beam subjected to the loading shown, derive equations for the shear force Vand the bending moment M for any location in the beam. (Place the origin at point A.) Let a-10.5 ft, b-24.0 ft, P- 20 kips and w - 5.5 kips/ft. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. B Calculate the reaction forces Ay and Cy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since A, - 0, it has been omitted from the free-body diagram.) Answers: kips Cy- kips Part 2 Determine the shear force acting at each of the following locations: (a) x = 10.5-ft (i.e., just to the left of point B) (b) x = 10.5+ ft (i.e., just to the right of point B) (c) x = 32.5 ft Note that x-0 at support A. When entering your answers, use the shear-force sign convention detailed in Section 7.2.…
For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let a-3.25 m, b=4.75 m, Pg - 35kN, and Pc = 80kN. Construct the shear- force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. A Ay- 58.66 - Dy- Calculate the reaction forces A, and Dy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) Answers: a 56.33 (a) V= (b) V- (c) V- B i i PB B kN с kN C Determine the shear force acting at each of the following locations: (a) x-2m (b)x - 4 m (c) x-8 m Note that x = 0 at support A. When entering your answers, use the shear-force sign convention detailed in Section 7.2. 3 3 3 KN D b kN D ·x Dy