Q2: A wind farm is proposed to be built outside of Baghdad Airport, The airport wind dataobtained at a zref = 10 m., gave a Weibull wind frequency distribution fit with coemciensof k = 1.54 andc = 3.78 m/s. The wind turbines in the proposed wind farm have a ratedpower of Prated = 1.5 MW,a rotor radius of R = 35 m, and a hub height of H = 65 m. The rated wind speed for thewind turbines is Vrated = 8 m/s and the cut-out wind speed is Veutout = 20 m/s. Find thefollowings:(a) Based on the Weibull coefficients at zref= 10 m., determine the newWeibull coefficients for the wind speed at the wind turbine hub height. Assume n =0.23.(b) What is the probability for the wind at the hub height to be between Vrated and Veutoul?(c) Based on this, what is the expected Annual Energy Production (AEP) [MW-h], for oneof the wind turbines in the wind farm?Q3:

Let us calculate the yield required 65 m annually.The yield required per hour =65 m10^qw / (365 x…

Q2: A wind farm is proposed to be built outside of Baghdad Airport. The airport wind data Obtained at a zref = 10 m., gave a Weibull wind frequency distribution fit with coefficients of k = 1.54 and c = 3.78 m/s. The wind turbines in the proposed wind farm have a rated power of Prated = 1.5 MW, a rotor radius of R = 35 m, and a hub height of H = 65 m. The rated wind speed for the wind turbines is Vrated = 8 m/s and the cut-out wind speed is Vcutout = 20 m/s. Find the followings: (a) Based on the Weibull coefficients at zref= 10 m., determine the new Weibull coefficients for the wind speed at the wind turbine hub height. Assume n = 0.23. (b) What is the probability for the wind at the hub height to be between Vrated and Veutoul? (c) Based on this, what is the expected Annual Encrgy Production (AEP) [MW-h], for one of the wind turbines in the wind farm?

Q2: A wind farm is proposed to be built outside of Baghdad Airport. The airport wind data Obtained at a zref = 10 m., gave a Weibull wind frequency distribution fit with coefficients of k = 1.54 and c = 3.78 m/s. The wind turbines in the proposed wind farm have a rated power of Prated = 1.5 MW, a rotor radius of R = 35 m, and a hub height of H = 65 m. The rated wind speed for the wind turbines is Vrated = 8 m/s and the cut-out wind speed is Vcutout = 20 m/s. Find the followings: (a) Based on the Weibull coefficients at zref= 10 m., determine the new Weibull coefficients for the wind speed at the wind turbine hub height. Assume n = 0.23. (b) What is the probability for the wind at the hub height to be between Vrated and Veutoul? (c) Based on this, what is the expected Annual Encrgy Production (AEP) [MW-h], for one of the wind turbines in the wind farm?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Find the size of a wind turbine rotor (diameter in m) that will generate 100kW of electrical power in a steady wind (hub height) of 7.5 m/s. Assume that the air density is 1.225 kg/m3, Cp = 16/27 and n = 1. %3D
Design a 1 MW wind Turbines: given data tower height : 80 mblade length: 38 maverage wind speed: 6.9 m/s power: 1 MW
Solve the ff. The discharge pressure of an air compressor is 5 times the suction pressure. If the volume flow at suction is 0.7m3/s and discharge volume flow of 0.2217m3/s, what is the compressor power(hp) if suction pressure is 100kpa. Ans. 191.72 A double acting air compressor has a cylinder dimension of 50cm x 60cm, 750rpm will have a volume displacement (m3/s) of: Ans. 2.945 A pump has a specific speed of 45 and 600rpm when it delivers 0.01m3/s. Find the head developed by the pump in ft. Ans. 926.07
A ship leaves port with drafts 7.6 m F and 7.9 m A; 400 tonnes of bunkers are burned from a space whose centre of gravity is 15 m forward of the centre of flotation, which is amidships. TPC 20 tonnes. MCT 1 cm = 300 tonnes m. Find the minimum amount of water which must be run into the forepeak tank (centre of gravity 60 m forward of the centre of flotation) in order to bring the draft aft to the maximum of 7.7 m. Find also the final draft forward.
02 h, are 12m. The pump efficiency is 79%, and the pump is driven by an electric motor. A pump moves water @10°C from a lake into a large, pressurized holding tank as shown. The flow rate, Q. is 375 L/min, and the piping system losses, 1) Sketch the setup (simple schematic is good), 2) label the z datum, and 3) identify and label the boundary conditions (P, V, and z) at 1 and 2 for use in a) the General Energy Equation (GEE). Provide values and units for the boundary conditions. Hint: For identifying good locations for boundary conditions, where are the velocities approximately zero? b) Calculate the head added to the fluid, h,, by the pump. Give your answer in units of m. Hint: Be careful with signs in manipulating the GEE. Show as many steps as you need to get your h, equation correct. Calculate the power added to the fluid by the pump in units of kW. () Determine the required electric motor size to drive the pump in units of HP. Prank = 200 kPa Holding Tank Air 6 m Pump Lake
PROBLEMI.2 A HYDRAULIC TURBINE IS REQUIRED TO PRODUCE 800 KW POWER AT 500 RPM UNDER A NET HEAD OF 40 M. FOR INITIAL TESTING A GEOMETRICALLY SIMILAR MODEL OF 1:4 SIZE NEEDS TO BE TESTED IN A LAB WHERE AVAILABLE HEAD IS 10 M.THE OPERATING SPEED AND POWER PRODUCED BY THE MODEL RESPECTIVELY IS
What is the maximum power generated by the wind farm with wind speed of 4 m/s? Typical wind turbines have rotor diameters from 40 m to 90 m (Assume increment of 5 m for this problem)-40 m is 80% efficient and efficiency decreases by 5% for every 5 m increase in diameter (i.e. 45 m=75%, 50=70...)-The ridge is 10 km long and wind turbines will be spaced in a single row. •Power in the wind per unit area of circular area is 1/2ρv3W/m2 (v is the wind speed, ρ is 1.3 kg/m3 for air) •Wind turbines cannot be spaced closer than 5 times its diameter without loosing power also there are no partial turbines.
A Pitot tube at a height of 3 m, measures wind velocity 5.3 m/s. What is the wind velocity at a height of 50 m? If the center of a 45 m diameter wind turbine is placed at 50 m, what is the maximum power this turbine may produce?
You are tasked to supervise the design of 0.5MW wind turbine to be constructed in the Wind Farm in Pililla, Rizal. Suppose the design criteria are as follows: The air density as surveyed after 2 year period averaged at 1.225 kg / cubic meter; the sweeping diameter of the rotor blades is 125m; and the anemometer reading in the area amounts to 4.2m/s on a 2 year period of survey. What is the theoretical power output of the turbine assuming 100% efficiency of operation?
A petrol engine has mechanical efficiency 0.8 and lower calorific value of 44.2 MJ / kg. The engine bore 0.06 m and stroke of 0.08 m. The engine speed of 2000 rpm. The consumption of fuel about 8 liter / h and the brake weight is 200 N. Take the density of fuel as 750 kg / m3 and torque arm of 400 mm.Find the specific fuel consumption. *
Q6.Starting from the fundamentals wind speed and the power relations, derive an expression for power in the upstream wind. (students should think logically and then answer this question)
2.5-L bench scale bioreactor is used for the production of recombinant P64K protein from Neisseria meningitides. The dimensions for the bioreactor are Dt 12.9 cm, ratio Di/Dt = 1/3 and N = 700 rpm. With the scale up factor of 2.24, determine the impeller tip speed (m/s) for the pilot scale bioreactor based on constant impeller tip speed and constant power consumption per volume. Predict which scale up method might give a higher concentration of P64K, if the demand of dissolved oxygen plays an important role.