Q2:- A model of a torpedo is tested in a towing tank at a velocity of 26 m/s whilst prototype is to run at 6.5 m/s.)What model scale has been used for water (kinematic viscosity=1.13E-4m²/s Also what would be the model speed if tested in wind tunnel under a pressure of 2000kPa and 27°C(dynamic viscosity for air 1.85E-4 Poise).

Q2:- A model of a torpedo is tested in a towing tank at a velocity of 26 m/s whilst prototype is to run at 6.5 m/s.)What model scale has been used for water (kinematic viscosity=1.13E-4m²/s Also what would be the model speed if tested in wind tunnel under a pressure of 2000kPa and 27°C(dynamic viscosity for air 1.85E-4 Poise).

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.8P

See similar textbooks

Similar questions

(b) The kinematic viscosity of a fluid used for model is one third of the kinematic viscosity of the fluid used for prototype. During testing of the model, if viscosity and gravity forces are predominant, find the scale ration, velocity ratio and discharge ration
The moment of the torpedo control unit in water was tested with a 1:8 scale scale model in a water tunnel of identical properties with a speed of 20 m/s if the measured moment in the model was 14 Nm. calculate 1) Determine the velocity of the prototype using the Reynolds number analogy. 2) Find the ratio of the forces occurring in the model and prototype. Using the analogy of Euler number 3) find the moment that occurred with the prototype.
A vehicle model is tested in a wind tunnel. The model scale is 1:2. The original speed of the vehicle is 72 km/h. The kinematic viscosity of the air is equal during the model test and the normal operation of the vehicle. What should be the flow velocity during the test? 40 m/s 36 km/h 288 km/h 20 m/s
Question 5 a) A 1:20 scale model of a surface vessel is used to test the influence of a proposed design on the wave drag. A wave drag of 6.2 lb is measured at a model speed of 8.0 ft/sec. What speed does this correspond to on the prototype, and what wave drag is predicted for the prototype? Neglect viscous effects, and assume the same fluid for model and prototype. b) Discuss the modelling and types of similarities
Question 5 a) A 1:20 scale model of a surface vessel is used to test the influence of a proposed design on the wave drag. A wave drag of 6.2 lb is measured at a model speed of 8.0 ft/sec. What speed does this correspond to on the prototype, and what wave drag is predicted for the prototype? Neglect viscous effects, and assume the same fluid for model and prototype.
The force on a component of a model in scale is 1:10 of a great bomb is measured as 45 N. Which force is expected at the prototypes component if its is used water for a model and the prototype: a) With water at the same temperature? b) With prototype's water at 10°C and a water from the model at 20°C? Rem = Rep; Fm = Fp where F = p.V^2.L^2
1 (a) A plate 0.05mm distant from a fixed plate moves at 1.15 m/s and required a force per unit area of 3.2 N/m? to maintain this speed with using an oil of specific gravity 0.7. Find the dynamic viscosity and kinematic viscosity of the fluid between the plates. 1 (b) Calculate the specific weight, density, and the specific gravity of a liquid having a volume of 662000 cm3 and weight of 64 kN
4. If the modulus of elasticity (E) for water is given to be 2.2GPa, what pressure is required to reduce the volume by 0.6%? 5. A tank contains two substance oil (A) and water (B) subject to variable air pressure: the dimension is shown below and corresponds to 1atm If air is
B) Compare between Two of the following 1- Open System and close system. 2- Otto cycle and Air-Standard cycle 3- Energy transfer by work and Energy transfer by Heal c) Find the dimensions of viscosity u. Write the dimensional formula of Force in the (FLT) rather than (MLT) systems.
%or l. ln. . o [Template] exami.. -> Ministry of Higher Education & Scientific Research Tikrit University College of Engineering Mechanical Engineering Dept. Class : 2nd year Subject: Principles of Fluid Mechanics Time: 1:15 hrs Date: 11/3 / 2021 Final Exam 2020-2021 Q1:-The gate AB as shown in fig.1 has long 1 m and wide 0.9 m .Find the force Fon The gate AB and also find the centre of pressure X 8 m 3 m Oil S-0.81 7 m Fig.1 Q2:- A wood cone floats in water in the position shown in fig.2.The specific gravity of the wood is 0.6.Would it be stable? D7m Fig.2 Water By Asst.Prof.Dr.Muhammad A.Eleiwi II >
Choose the correct answer Kinematic viscosity is * f. dynamic viscosity* Density b. About 1.2*10^-2 m2/s for water e. Both b and d c. Density*dynamic viscosity d. Both a and c g. Both f and c a. About 1.2*10^-6 m2/s for water
Q2) Fill in the blanks with appropriate word(s), for EXKEl of the following; K Specific weight is defined as According to the variation of density with pressure, Nuids may be classified into - Nuids and - Nuids. 3. The approximate number of experiments to evaluate the influence of 3 parameters separately is assuming that 5 experiments are needed for each variable. ¿When viscous resistance is important, -. criteria for similarity is used. S. The center of pressure is defined as - A Hydrostatic forces in a static fluid is the result of the exerted on submerged surfaces. Streamline is defined as Continuity equation represents the d 0, conservation of