Q1Q2A linear resistance potentiometer is 5 cm long and uniformly wound with a wire having aresistance of 10 kn. Under normal conditions, the slider is at the center of thepotentiometer. What will be the slider position when the resistance measured by thepotentiometer is:(i)(ii)A platinum resistance thermometer has a resistance of 100 22 at 25°C.(i)Find its resistance at 65°C. The resistance temperature coefficient of platinum is0.00392 2/(/°C.).(ii)3.8 ΚΩ8.3 ΚΩIf the thermometer has a resistance of 150 2, calculate the value of thetemperature.

1- The length of the wire of the potentiometer is, l=5 cm The resistance of the wire of the…

Q1 Q2 A linear resistance potentiometer is 5 cm long and uniformly wound with a wire having a resistance of 10 kn. Under normal conditions, the slider is at the center of the potentiometer. What will be the slider position when the resistance measured by the potentiometer is: 3.8 ΚΩ 8.3 ΚΩ (i) (ii) A platinum resistance thermometer has a resistance of 100 £2 at 25°C. (i) Find its resistance at 65°C. The resistance temperature coefficient of platinum is 0.00392 2/(/°C.). (ii) If the thermometer has a resistance of 150 2, calculate the value of the temperature.

Q1 Q2 A linear resistance potentiometer is 5 cm long and uniformly wound with a wire having a resistance of 10 kn. Under normal conditions, the slider is at the center of the potentiometer. What will be the slider position when the resistance measured by the potentiometer is: 3.8 ΚΩ 8.3 ΚΩ (i) (ii) A platinum resistance thermometer has a resistance of 100 £2 at 25°C. (i) Find its resistance at 65°C. The resistance temperature coefficient of platinum is 0.00392 2/(/°C.). (ii) If the thermometer has a resistance of 150 2, calculate the value of the temperature.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Half-wave rectifier loaded with R-L is fed with a 120 VAA 60 Hz source. 10 Ω loadFind the inductance value that limits the average load current to 5A for the resistance.
Question-4: (A) Show the voltage waveforms across each half of the secondary winding and across R1 when a 100 V peak sine wave is applied to the primary winding in Figure 2. (B) What minimum PIV rating must the diodes have? D 2:1 IN4001 +100 V -- V ov RL -100 V 10 kN IN4001
aph R₁ 100 ΚΩ R₂ www R₁ 1.0 kn body 1. Determine the necessary value of R2 in Figure 4 so that the circuit will oscillate. Neglect the forward resistance of the Zener diodes. (Hint: The total gain of the circuit must be 3 when the Zener diodes are conducting.) 2. Explain the purpose of R₁ in Figure 4. www. body bold 6.8 V 6.8 V R3 47 ΚΩ R₁ www 1.0 kn 0.015 μF Normal 0.015 µF No Spacing Styles He
For solar cell the Open Circuit Voltage (Voc) occurs when O a. voltage is minimium f O b. voltage is zero ion O C. current is maximium O d. current is zero page
A Moving to another question will save this response. Question 13 The density of doping of zener diode is less than normal diode. True False A Moving to another question vwill save this response. Windows
For the diode circuit shown below, indicate the ON/OFF condition for all the diodes given VA and VB values. Calculate Vout, Vx and all the currents that flow through the diodes. Summarize your result using a table. +4V VA VB VA OV OV 4V D₁ D₂ X 5ΚΩ D3 VB OV 4V 4V -2V 5ΚΩ VOUT
ii. The controlled single-phase rectifier full-wave bridge rectifier of Figure ii has an RL load with R = 252 and L = 50mH. The source is 240 V rms at 60 Hz. Determine 15° and a = 750 the average load current for a = v, (or) = Vm sin(or) Figure 2: For part (c) ii
1-32. Calculate the voltage across the diodes given that the reverse bias saturation current in D₁ is Is1 = 175 nA, and 7,2 = 100 nA. 50 Ω 1400 mA DI D₂ Vo
DIODES ARE IDEAL. I need the answer asap thank you
A dc voltmeter has a sensitivity of 1000 92/V. When it measures half full scale in 100 V range, the current through the voltmeter is?
What are the states for diodes in the figure below? D1 D2 4 k2 10 V 10 V O a. D1 off D2 on O b. D1 off D2 off O c. D1 on D2 off O d. D1 on D2 on
A RTD made up of platinum has a=0.00385 and has a initial resistance of 220. Find the value of resistance Rt for the following temperatures. Temperature Resistance (Rt) 610 -30 1.Resistance (Rt) at Temperature 610°C = 2. Resistance (Rt) at Temperature -30°C =