Q: The working fluid, in a steady flow process flows at a rate of 220 kg/min. thefluid rejects 100 kj/s passing through the system. The conditions of the fluid at inletand outlet are given as: cl= 320 m/s, pl=6.0 bar, ul= 2000 kg/kg, v1= 0.36m3/kgand c2= 140 m/s, p2= 1.2 bar, u2= 1400 kj/kg, v2= 1.3 m3/kg. Determine the powercapacity of the system in MW. The change in potential energy may be neglected.

Given Flow rate=220kg/min C1=320m/s P1=6.0bar C2=140m/s P2=1.2bar

Q: The working fluid, in a steady flow process flows at a rate of 220 kg/min. the fluid rejects 100 kj/s passing through the system. The conditions of the fluid at inlet and outlet are given as: c1= 320 m/s, pl=6.0 bar, ul= 2000 kg/kg, v1= 0.36m3/kg and c2= 140 m/s, p2= 1.2 bar, u2= 1400 kj/kg, v2= 1.3 m3/kg. Determine the power capacity of the system in MW. The change in potential energy may be neglected.

Q: The working fluid, in a steady flow process flows at a rate of 220 kg/min. the fluid rejects 100 kj/s passing through the system. The conditions of the fluid at inlet and outlet are given as: c1= 320 m/s, pl=6.0 bar, ul= 2000 kg/kg, v1= 0.36m3/kg and c2= 140 m/s, p2= 1.2 bar, u2= 1400 kj/kg, v2= 1.3 m3/kg. Determine the power capacity of the system in MW. The change in potential energy may be neglected.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Gasoline flows steadily downward through the pipe shown in the figure below. Viscous effects are negligible, and the pressure gage indicates the pressure is zero at point (1). Determine (a) the flowrate and (b) the pressure at point (2). (a) Q = (b) p2 = 2.0ft 3.5ft 18 -0.12 ft -0.1 ft -free jet ft³/s lb/ft²
Problem 2 -50 A glass 12 cm tall filled with water is inverted. The bottom is open. What is pressure at the closed end? Barometric pressure is 101.325 kPa. the Ans: 100.15 kPaa Problem 2 -51 In Figure 13, in which fluid will a pressure of 700 kPa first be achieved? Ans: glycerin Po = 90 kPa ethyl alcohol p= 773.3 kg/m 60 m oil p= 899.6 kg/m? 10 m water p = 979 kg/m glycerin p = 1236 kg/m 5 m 5 m
The tank contains a liquid having a density of 2.52 slugs/ft^3 10 in 5 ft 10 ft. 7 ft Pliquid 2. 52 slugs/ſt³ %3D a. Determine the unit weight of the liquid when it reaches the indicated level. b. Determine the liquid's weight. Use English units to express your response. c. Assuming no mixing of liquids occur, if glycerin (SG = 1.26) is poured into the tank, will it sink to the bottom, or will it float on the surface of the liquid, or will it be suspended in the liquid?
A glass 12 cm tall filled with water is invert the pressure at the closed end? Barometric pressure is 101.325 kPa. What is Ans. 100.15 kPaa Problem 2- 51 In Figure 13, in which fluid will a pressure of 700 kPa first be achieved? Ans: glycerin Proble Po 90 kPa A diffe water ethyl alcohol p= 773.3 kg/m³ mm, 1 betwe 60 m ol p= 899.6 kg/m 10 m water P= 979 kg/m' glycerin p = 1236 kg/m 5 m 5 m 2021/04/16 18:27
(a) Glycerine at 25 °C flows through a straight copper tube (D = 73.8 mm), at a flow rate of 180 L/min. Calculate the pressure difference between 2 points which are 25.8 m apart, if the first point is 0.68 m below the second point. Gven: At 25 °C density and dynamic viscosity for glycerine is 1286kg/ and 0.96 Pa.s respectively(b) If benzene at 50 °C is used in question (a) above instead of glycerine, evaluate the new pressure difference. ...
5. Airat standard conditions enters the compressor shown below through a 2.4-in diameter pipe at 10 cfs. It leaves the tank through a 1.2-in diameter pipe at a velocity of 700 fps and has an increased density. Determine the average time rate of change of air density within the tank. 2.4 in 10 cfs 1.2 in 700 fps 0.00350 slugs/ft Tank Volume = 50 ft 0.00238 slugs/ft
In a given setup, distilled water flows towards the inside and goes outside of the vessel as shown in the figure. What is the rate of change of the water's mass (dm/dt) in the vessel? 3 in. Q = 0.3 ft3/sec V = 30 ft/sec Device m = 0.3 slug/sec %3D
1. Oil flows through a 200 mm diameter pipe A at 2 m/s and through a 250 mm diameter pipe B at 1 m/s and discharges through a 150 mm diameter pipe C. Specific gravity of oil are 0.9, respectively. a) Determine the discharge at pipe C. b) If alcohol flows through pipe B. Determine the average density of the two fluids as the mixture flows through the pipe at C. Specific gravity of alcohol is 0.78. B ↑
a.)In the figure shown in no.1, in which fluid will a gage pressure of 60 kPa first be achieved? b.)In the figure, in which fluid will a gage pressure of 80 kPa first be achieved?*
•Determine the unit weight of the liquid when it is at the level shown. (Express the answer in English unit) •Determine the weight of the liquid. (Express the answer in English unit) •Assuming no mixing of liquids occur, if glycerin (SG= 1.26) is poured into the tank: a.) it will sink to the bottom of the tank b.) it will float on the surface of the liquid c.) it will be suspended in the liquid * answer should be in 3 decimal places
mm mim 0.20 m Q3. A. soap bubble 60.0 mm in diameter has an internal pressure in excess of the outside pressure of 25 N/m2. What is the tension in the soap film. 3. What is the non-Newtonian fluids and what are types? (mention 3 examples).
The distance Ah is the height of the liquid in the manomoter above the heavier liquid in the tank. D 10 cm Water Ah = ? B C 20 cm S= 3.0