Q: A power station of 2 MW is to supply two regions A & B. The daily of loads are given below Time in hours Region A in Kw 0-6 6-14 14-20 20-24 500 800 600 Time in hours Region B in Kw 0-4 4-10 10-18 18-24 400 200 800 600 1. Draw the load curve on the power station if the max demand load is 1600 and the load factor is 0.640625 2. calculate plant use factor if Load B is totally disconnected 3. calculate diversity factor.

Q: A power station of 2 MW is to supply two regions A & B. The daily of loads are given below Time in hours Region A in Kw 0-6 6-14 14-20 20-24 500 800 600 Time in hours Region B in Kw 0-4 4-10 10-18 18-24 400 200 800 600 1. Draw the load curve on the power station if the max demand load is 1600 and the load factor is 0.640625 2. calculate plant use factor if Load B is totally disconnected 3. calculate diversity factor.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.61P

See similar textbooks

Similar questions

A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and L=40mH. (a) Determine the power factor of the circuit and state whether it is lagging or leading. (b) Determine the real and reactive power absorbed by the load. (c) Calculate the peak magnetic energy Wint stored in the inductor by using the expression Wint=L(Irms)2 and check whether the reactive power Q=Wint is satisfied. (Note: The instantaneous magnetic energy storage fluctuates between zero and the peak energy. This energy must be sent twice each cycle to the load from the source by means of reactive power flows.)
Use the information below to answer questions 24 und 25. The voltage across and the current through a load are (10+ j5Y and (2-jiArespecively. 24. What is the reactive power in VArconsumed? D. 0 A. 15 C. 20 D. 25 25. What is the pawer factor of the load? A. 0.8 leading B. 0.8 Jagging. -D. 0.6 ligging C 0.6 leading
A 400 MVA synchronous machine has H, = 4.6 MJ/MVA and a 1200 MVA machine has H₂=3.0 MJ/MVA. The two machines operate in parallel in a power plant. Find out H relative to a 100 MVA base.
What will be the value of the twiddle factor: W42
The actual impedance of a load is 10 OHM. The new per-unit impedance of the load is 0.5 pu when Base Voltage is 200 V and Base Power is O 4000 VA O 8000 VA O 6000 VA O 2000 VA
A generating station has the following daily load cycle: Time (Hours)0-55-8 8 – 12 12 – 15 15 – 20 20 – 24 Load (MW) 20 40 60 50 80 40 Draw the load curve and find (i) maximum demand (ii) units generated per day (iii) average load and (iv) load factor.
The actual impedance of a load is 30 OHM. The per-unit impedance of the load is 0.5 pu when Base Voltage is 600 V and Base Power is O 6000 VA O 2000 VA O 4000 VA 8000 VA
The actual impedance of a load is 10 OHM. The new per-unit impedance of the load is 0.5 pu when Base Voltage is 200 V and Base Power Is O 4000 VA CO 8000 VA O 6000 VÀ O 2000 VA
%23 IoA 1172 IAB wwww IBC 20L-90°y -J992 204 30°y A ICA IcC a) Find the load current ICA ? b) Give the line yoltoge Vab? C Calculate the total complex power over the saurces of the voltoge7 www
6. What is the effect of load inductance on the ripple current? 7. i effect of chonnine Bock and boost 8. Wh 9 What chopping 10. At what duty evcle does the load current rinnle current he
A generating station has the following daily load cycle: [10] Time 0-6 6-10 10-12 12-16 16-20 20-24 (Hours) Load 40 50 60 50 70 40 (MW) Draw the load curve and find (i) maximum demand (ii) units generated per day (iii) average load and (iv) load factor.
If a Load absorbs 10 kVA at a leading power factor of 0.6. Then the complex power is: Select one: a. -6000 - j8000 VA b. 6000 + j8000 VÀ c. 6000 - j8000 VÀ d. None of these