Problem- The circular base of a cylindrical tank is of 1 m diameter and has an orifice of 10 cm diameter. The discharge coefficient Cd for the orifice is 0.6. Initially the tank is empty and then it is filled from top using a pipe discharging 0.025 m³/s. How long will it take to fill the tank up to a height of 1 m? What will be the maximum height of 1 m? What will be the maximum height to which the tank can be filled?

Problem- The circular base of a cylindrical tank is of 1 m diameter and has an orifice of 10 cm diameter. The discharge coefficient Cd for the orifice is 0.6. Initially the tank is empty and then it is filled from top using a pipe discharging 0.025 m³/s. How long will it take to fill the tank up to a height of 1 m? What will be the maximum height of 1 m? What will be the maximum height to which the tank can be filled?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem-4, A pipe of 0.7 m diameter has a length of 6 km and connects two reservoirs A and B. The water level in reservoir A is at an elevation 30 m above the water level in reservoir B. Halfway along the pipe line, there is a branch through which water can be supplied to a third reservoir C. The friction factor of the pipe is 0.024. The quantity of water discharged into reservoir C is 0.15 m³/s. Considering the acceleration due to gravity as 9.81 m/s² and neglecting minor losses, the discharge (in m³/s) into the reservoir B is
3. A permeameter is filled with sand. When water is allowed to flow through the device, a flow rate of Q.er = 10 cm'/s is observed. The sand is dried and filled with oil. The total hydraulic head at the inflow and outflow ends of the permeameter are the same in both tests. Calculate the flow rate of oil Qol. Data: puil=0.9 pwaer Hlail = 1.8 lue
QUESTION 4 Two tanks with a difference in water levels of 180 m are shown in Figure Q4. The tanks are connected by a 64 km long pipe of 600 mm diameter with friction factor f= 0.01i5. () Determine the discharge through the pipe (ii) In order to increase the discharge by 50%, another pipe of the same diameter is to be laid from the lower tank for part of the length and connected to the first pipe. Determine the length of the additional pipe required. H-180m 2 Figure Q4
I need right solution with clear calculations. If you don't know the solution please leave it but don't give me wrong solution. A 100 mm diameter well is drilled to withdraw water from a 11 m thick confined aquifer having coefficient of permeability equal to 64.8 m/d. The depth of water below the piezometric level is 30 m and it falls 2 m in the well while pumping. Calculate the discharge from the well when the radius of the circle of influence is 50 m.
A 2.5-m square vertical tank 4 m high contains 3.5 m of oil (SG-0.82). A 100 mm diameter circular sharp- edged orifice is located 50cm above its bottom. Assume c=0.64, how long will it take to lower the water level to 1 m deep after opening the orifice? O 10.5 min O 6.85 min O 9.59 min O 8.15 min
2. The figure shown below is a subsoil is anisotropic and has permeabilities k k, = 2.0 x 10 in./sec. Find the rate of flow beneath the dam per foot cross section of a concrete dam. The = 0.8 x 10 in./sec and length of the dam. Assume NE 4, and Na = 8. 55 ft 32 ft Concrete dam 3 ft IAVIA IAVIA AVIA
A tank shaped in a frustum of a cone has a lower base radius 1 m, upper base radius 0.50 m and an altitude of 10 m. It is filled with water to a depth of 4 m. The water is then transferred to a spherical tank with radius 5 m. What is the depth of the water in the second tank in meter?
a circular tank of diameter 1.25m contains water up to a height of 5 m.Am arifice of 50mm diameter is provided at its bottom if CD is 0.62. Solve the height of water above the arifice after 1.25 minutes and 17 minutes
3.11 For the closed tank with Bourdon-tube gages tapped into it, what is the specific gravity of the oil and the pressure reading on gage C? 0.5 m Air 4 PA=50.0 kPa 1.0 m Oil 0.5 m B P= 58.53 kPa 1.0 m Water 0.5 m C Pc=? T= 10°C PROBLEM 3.11
The two reservoirs connected by a smooth pipe below contain water at 20 °C. Ignoring minor losses in the system what is the flow rate for Az = 97 m if the pipe has the following properties: • L = 7 km • D = 50 mm Δz 1 DI L, d, E 27 (a) What is the friction factor? Please provide your answer to 2 significant figures. Number (b) What is the flow rate? Please provide your answer to 3 significant figures. Number Units
Q1) A pipe line 30 cm in diameter and 3200m long is used to pump up 50 kg/sec. of an oil where its density is 950 kg/m3 and kinematic viscosity equal to 2.1 stokes. The center of the pipe line at the upper end is 40m above that at the lower end. The discharge at the upper end is atmospheric. Find: 1) Pressure at the lower end as a head of water 2) Friction factor f (Darcy coefficient) 3) Reynolds number
A storage tank contains a liquid at depth y where y=0 when the tank is half full. Liquid is withdrawn at a constant flow rate Q to meets demands. The Contents are resupplied at a sinusoidal rate 30sin (t). Equation can be written as: d(Ay) = 3Q sin?(1) – Q (1)p (change in` (inflow) – (outflow) volume since the surface area A is constant sin²ce) – O A dy d(t) Use Euler's method to solve for the depth y from t = 0 to 10 d with a step size of 0.5 d. The parameter values are A = 1200 m? and Q = 500 m/d. Assume that the initial condition is y = 0.