Answered: Problem No. 1 An earth embankment…

Problem No. 1 An earth embankment diagram is shown in Figure. Determine the stress increase at point A due to the embankment load. 6 m Unit 3 m 3 m

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter10: Stresses In A Soil Mass

Section: Chapter Questions

Problem 10.13P: Repeat Problem 10.12 for q = 700 kN/m2, B = 8 m, and z = 4 m. In this case, point A is located below...

See similar textbooks

Related questions

Q: What is the height of building a if a man who is stay away 65m from a buidling and make an elevatio...

Q: Calculate the value of h, in meters, in the Venturi meter shown in the volumetric flow rate of water...

Q: red thickness of the plate. (Hint: HOLE vs FILL vable stress based on minimum thickness of the e on ...

Q: Q1) An earthen channel is excavated in a sandy clay bed with a particle size d50- 3.0mm where the be...

A: step 1-

Q: 20 KN F

A: By using joint method, Take joint F, So, we have two member in this FD and FE. Now we need to find a...

Q: 10 cumecs of water is delivered to a 20 hac. field for 5 hours. Soil probing after the irrigation in...

A: We will apply formula for water application efficiency.

Q: A soil has liquid limit 65%, plastic limit of 30% and shrinkage limit of 25%, and it has natural moi...

Q: Shear and moment diagram on beams

Q: A dry sand 10 m thick has an in-situ dry unit weight of 18 kN/m^3. Using vibroflotation, the surface...

A: Dry unit weight of sand = 18 KN/ m3 Thickness of layer of sand before compaction = 10 m. Thickness o...

Q: What is the height of building a if a man who is stay away 30m from a buidling and make an elevatio...

Q: 3. A dam will have a first cost of Php 50,000,000 an annual maintenance cost of Php 250,000 and mino...

Q: Analyse the structure shown in Figure using consistent deformation methods, then draw the Shear forc...

A: Using method of consistent deformation ### drawing of SFD and BMD#### Assuming EI=1×10^4 KNm^2

Q: Determine the value of angle of internal friction if coefficient of active earth pressure 1/4

A: Given data : The value of active earth pressure=Ka Ka=14 To find : Angle of internal friction

Q: A propped cantilever beam having a span of 6 m is loaded with a uniformly distributed load of 12kN/m...

A: As per bartleby guidelines experts are allowed to solve only first three parts of the question. Ple...

Q: if the normal stress in x direction is 14 Ksi and the normal stress in the y direction is 9 Ksi and ...

A: Given data : Normal stress in X direction σX=14 ksi Normal stress in Y direction σY=9 ksi Minimum pr...

Q: A river model is constructed to a horizontal scale of 1:1000 and a vertical scale of 1: 100. If the ...

Q: Water is flowing at the rate of 300 lit/sec from A to E as shown in the figure. Compute the flow in ...

A: Given, Water flow rate =300 lit/sec f=0.025 LAB=300 m LBC=600 m LCD=600 m...

Q: = 2" d2 = 2.375'' d3 = 2.25'' d4 = 2.5''

Q: Q1. Analyze the frame shown in fig.1 by slope deflection method and draw SFD and BMD. E value is con...

Q: Find the force in member BD. 20 KN 10 KN 4.0000 20 KN 4.0000 3.0000 3.0000

Q: What is the importance of AASHTO T 248 in civil engineering?

Q: 250 mm A1 50 mm Neutral Axis (N.A) 280 mm A2 Reference Line 60 mm For the T-section shown in the fig...

Q: 2)Design the concrete mix using the following conditions:(ACI Method) Summarize also the total batch...

Q: . How far will the 100-kg block move 2 seconds after it is released from the position shown. The pul...

Q: ceel rod was fitted on the copper tube and N. Calculate the working stress of the rod ar 200 GPa r =...

Q: Given a 9.92 m built-up column pinned at the top and fixed at the bottom with the following properti...

Q: constant head permeameter, 85 mm in diameter containing fine sand sample 450 mm long, allowed water ...

Q: Find the value of velocity if discahrge through channel is 0.9 m3/s and cross area is 1 m2

A: Given data : The value of discharge Q=0.9 m3/s The value of cross sectional area A=1 m2 To find : ...

Q: IN A NOMINAL 90° TRIANGULAR NOTCH DISCHARGING UNDER INVARIANT HEAD, THE ERROR IN THE ESTIMATED DISCH...

Q: 1. How much force is required to punch a 25-mm diameter hole in the plate that is 30 mm thick? punch...

Q: e elongation of the bar from e load P = 30kips.

Q: Let having all the expenditure, Rs 100 be the cost/hr of a shovel with volume 10 m which will be use...

Q: Calculate degree of static indeterminacy

A: Given data : The number of member in truss m=11 The number of Joint in truss J=7 The number of exter...

Q: 80 kN 40 kN 60 kN -10 kN/m A m E 2 m 1 m, 3 m 3 m 2 m 1 m (b)

Q: Suppose that a blast site is located 100 meters from a farmhouse. Determine the expected damage from...

A: Given, Distance (R) = 100 m K = 100 Maximum instantaneous charge (Q) = 3307 lbs or 1500 kg

Q: Take Distance AB=188 m

A: Given data : True length of chain L=30 m Wrong length of chain L'=30.04 m Wrong length of line measu...

Q: What are the different stages of cost benefit analysis? Explain briefly each stage.

A: The different stages of Cost-Benefit Analysis model are as follows: 1. Defining the framework for th...

Q: A two-tier pipe system is use to support an applied loads PA and PB as shown in the figure. Determin...

Q: Problem 1 A 300 mm x 400 mm column is to be supported by a 2 m x 2 m x 0.4 m thick footing @ its cen...

A: Solution: Given: column = 0.3 x 0.4 m footing = 2 x 2 x 0.4 m DL = 520 kN, LL = 320 kN centroid = 0....

Q: Briefly explain the importance of method statements in construction project

A: We have to determine the importance of method statement in construction project as per the construct...

Q: A 150mm diameter cylindrical concrete specimen was tested for splitting tensile strength. The Sample...

A: Splitting Tensile strength can be defined as a maximum amount of stress acting on tension side of un...

Q: A floor plan shown below is subjected to an imposed load of 2.5 kN/m². and a floor finish load of 1....

A: Lx=3mLy=8mLL=2.5 kN/m2DL=1.5 kN/m2fy=500 MPaFc=25 MPaγc=25 kN/m3

Q: Explain which geometrical properties of a structure contour set on a map define the orientation of a...

Q: Find the force in member AB. 3 0000 40 KN 40 KN 3 0000 3 0000 3.0000 3.0000

Q: What is the internal bending moment al point B (including the sign based on the sign convention for ...

A: Given data : The value of Point load F1=6 KN The value of Point load F2=10 KN The value of moment M=...

Q: Among the test coupon you were provided with, which material has the highest potential for strain ha...

A: Given data,

Q: A canal and a stream run parallel to each other at a separation distance of 400 m. Both of them comp...

Q: Six columns rest on a foundation slab 10 m wide and 11 m long. Each column has a dead load of 1500 k...

A: We will calculate load on six columns and divide by area of slab.

Q: A flow is described by the stream function y = 3/2xy . Locate the %3D point at which the velocity ve...

Q: If E is assumed to be correct and there is an error of 1.5 % in the determination of modulus of rigi...

Concept explainers

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.

Question

Problem No. 1
An earth embankment diagram is shown in Figure. Determine the stress increase at point A due
to the embankment load.
6 m
Unit weight N
3 m
3 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

2: An embankment shown in the figure is constructed. compute the vertical stress increment under Points A. B. and C at z = 10 m Use vertical stress Increment under an embankment loads? 10 m 12 m 10 m Y₁-192 kN/m² Take value of 15 from chart s6v=9[s
With B,lz and Blz is showr CE 12 s Name: ID: Problem No. 1 For the embankment shown in Figure below, determine the vertical stress increases at points 4, B, and C. 5m 5 m 10 m Unit weight y 17Na 5 m
Determine the stress increase due to the embankment load at point A as shown in Figure 2. The unit weight of the embankment fill is 115pcf
Q#3. An earth embankment diagram is shown in Figure.1. Determine the vertical stress increase at A due to embankment load.
An embankment load on a silty clay soil layer as shown below. Determine the stress increase under the embankment at points A and B that are loaded at a depth of 6 m below the ground surface. 5 m 1H:2V 1H:2V 1H:1V 8 m 13 y=18 kN/m Y=18 kN/m³ 6 m : B : A CS Scanned with CamScanner
An earth embankment is shown in the figure. Determine the stress increase at 2. point A due to the embankment load. 7 m 15 m Unit Weight 19 kN/m' %3D 8m 10 points 2. Increase in stress
Q: You have been assigned to check the stability of a pond constructed in stiff saturated clay underlain by a layer of sand. The necessary information are given in the following figure. (i) Find effective stress at A and determine the stability of cut under given condition. (ii) What should be water level into the pond to ensure factor of safety = 1.5. (Given that yw = 9.81 kN/m³) H = 5 m 7m 2m 2m J Saturated clay Sand Ysat = 16 kN/m³ 4m Ysat = 15 kN/m³
Take o, = 580 kPa (Figure 1) Express your answer to three significant figures and include the appropriate units. HÀ ? o, = Value Units Submit Request Answer Figure Part B Determine the shear stress acting on the inclined plane AB. Express your answer to three significant figures and include the appropriate units. В HA ? 30° Value Units A
for an embankment loading shown on the figure, determine the vertical stress on the points A, B, and C
A circular Beam with roller joint R L y y oo = 298.6055 Pa Ro = 2.0649 m L = 61 m Material Data E[ GPA] Oyp [MPa] p [kg/m^3 V 200 0.3 700 7800 Find: Displacement in X, Y, Z direction, von misses stress, tresca stress, and triaxial stress at x = L, at x = L/2 and x = 0. Please show all work
An embankment is shown in the figure. Determine the stress increase (in kPa) under the embankment at points A₁ at a depth of 8m and A₂ at a depth 4m. 5 m = 14 m -11.5 m- B₂ 4-1(+3)()-(G B (α₂ B₂ 5 m H 7 m -14 m- y=17 kN/m² 16.5 m
An embankment load on a silty clay soil layer as shown below. Determine the stress increase under the embankment at points A and B that are loaded at a depth of 6 m below the ground surface, please use figure (10.20). 5 m 1Н:2V, 1H:2V 1H:1V 8 m y=18 kN/m y=18 kN/m" 6 m : B Figure 10.19 Embankment loading 0.50- 3.0 20 16 0.45- 14 1.2 LO 0.40 - 0.9 0.8 0.7 0.35 - 0.6 030- 05 04 * 025 - 03 0.20 - 0.2 0.15 - 0.10 - 0.1 0.05- Figure 10.20 Osterberg's chart for determination of vertical stress 0.00 TI TT - due to embank- 01 0.1 10 ment loading 100 327