Problem II. Solve the problem using Conjugate Beam Method.The beam shown has a constant El and is supported as shown. Find the following:300 KN15 kN/ma. Reaction at A (KN)slim1.5 kNmb. Reaction at B (kN)Bсc. Slope at C in radians2m10md. Displacement at the application of 300kN loadm | 3m | 3m t

Answered: Image /qna-images/answer/ba2ac1b6-3a4b-45be-9b80-4077b5562978.jpg

Problem II. Solve the problem using Conjugate Beam Method. The beam shown has a constant El and is supported as shown. Find the following: 300 KN a. Reaction at A (KN) b. Reaction at B (kN) с c. Slope at C in radians d. Displacement at the application of 300kN load حتی 1.5 kNm 15 kN/m B 2m m | 3m | 3m t 10m

Problem II. Solve the problem using Conjugate Beam Method. The beam shown has a constant El and is supported as shown. Find the following: 300 KN a. Reaction at A (KN) b. Reaction at B (kN) с c. Slope at C in radians d. Displacement at the application of 300kN load حتی 1.5 kNm 15 kN/m B 2m m | 3m | 3m t 10m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

a. Determine the reaction R1 of the beam loaded as shown in Newtons b. Find the value of EIy at the position midway between the supports for the beam shown. c. Find the value of EIy at the overhanging end for the beam shown use double integration method
Develop the flexibility matrix for the beams with respect to the co-ordinates shown in figure. 21 2m 1 I 2
Below presents a continuous beam with A being fixed and B is pinned and C has a roller. Take: E = 200 GPa 1 = 8 x 106mm Load = 2 kN A 5m B Using the following method: 2 KN + 2m + 2m |- You are tasked to analyze the continuous beam by calculating the: > the displacement on the beam at B and C and > the reaction at the supports Matrix Structural Analysis Use the following steps as a guide to analyze the beam: Matrix Structural Analysis ✓ Produce Notations ✓ Establish the known displacements and known external load ✓ Produce Member Stiffness Matrix ✓ Displacement and Load ✓ Calculating the displacement Calculating the reaction at the support
Use the double integration method and find the reactions. Determine the following. a) EIy at 1meter from pin support b) EIy' at midspan c) EIy at 1meter from left support. ASAP
Q2. Determine the density of the rectangular component (i.e. a) in kg/m and the location of the equivalent point load measured from point A so that it causes an upward 50 N force and a 300 Nm couple moment reactions at A. A a kg/m 0.5 m
A torque of 500 NMm is applied to the circular beam of variable radius given in the figure in the direction shown at point C. Find the support reactions at A and B points.
Derive the equation of the resonance frequency of the uniform cantilever beam shown below by using method of conservation of energy. [Solution tips: Umax, maximum strain energy is equal to max. kinetic energy of vibrating body.] j'm dx ( M(x)² T. U = max El xp- 1/2
The beam shown below is suspended from two steel rods as shown and is initially horizontal. The midpoint B of the beam is deflected 15 mm downward by force Q. The steel used for the rods has properties E = 200 GPa and σ = 275 MPa, determinea. the required maximum value of Q.b. the deformation of rod AD.c. the deformation of rod CE.
A rigid beam BC is suspended by rods AB and CD as shown in the figure. Rod AB is made in from aluminum while rod CD is made from steel. Determine the location/placement of the 75kN concentrated load within the beam BC such that the rigid beam BC will remain horizontal after deflection. Determine the axial deformation of rods AB and CD.
The system shown in the figure has a fixed support at A and an alumimum rod of 0.5m length at C. The beam AC is subjected to a point load of 20 kN at its midspan. In addition to that point load, alumimum rod is subjected to a temperature decrease of 25 °C. Determine the deflection and the rotation at point C. Anhunnd 70 GP in
Two steel pipe columns (E=200,000 MPa,A1=2000mm2,A2=1800mm2)support a rigid beam AC that has a 3.6m overhang BC. The beam supports a linearly varying load of maximum intensity w=75K/nm as shownin the figure.Neglect the weight of the beam AC, and assume that the beam is supported on the two columns such that it transmits load to each column as an axial load.Determine the vertical displacementat end C of the beam, in column 1at A and column 2at B. Answer in mm.
(a) Based on the theory of deflection beam, state the boundary conditions of two beamsas shown in Figure Q2(a).