Answered: PROBLEM 4 A standpipe with an open top…

PROBLEM 4 A standpipe with an open top has a diameter of 2.5m and a wall thickness of 22mm. What level of water from the bottom will result to a hoop stress of 15MPA of the standpipe?

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter16: Lateral Earth Pressure

Section: Chapter Questions

Problem 16.15P

See similar textbooks

Related questions

Q: A 450 mm square tied RC column is to carry axial service loads of 1500 kN dead load and 800 kN live ...

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the exac...

Q: 3. The density of alcohol is 790 kg/m³. Calculate its specific weight, specific gravity and specific...

A: Density=7o0kg/m3

Q: 75 b 100 bt 2

A: Given data:

Q: Calculate the pressure due to a column of 10.0m of (a) water, (b) mercury of sp. gr. 13.6, and (c) a...

Q: Hydrologic systems are sometimes impacted by extreme events, such as severe storms, floods, and drou...

Q: What is the hazard associated with a centrifuge, and how will you minimize the risk

A: Hazards Associated with a Centrifuge:- If centrifuges used and/or maintained in a improper way, th...

Q: The uniform 25 kN bar BC is supported by a pin at C and the aluminum wire AB. The cross-sectional ar...

Q: e two center grade lines are to be connected by a 250-meter vertical parabolic curve. Complete solut...

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and s...

Q: From the figure shown, which of the following most nearly gives the block shear strength?

A: Taking question available in image Gross area = 2530 mm2 d= 229 mm tw = 5.90 mm bf = 61 mm tf = 10.5...

Q: rXS 20 rxss COD: 35 mg/L, BOD: 7 mg/L, AN: 2.5 mg/L, SS: 475 mg/L, pH: 5, DO: 5 mg/L SICOD-991-133X ...

A: AN=2.5mg/L DO=5mg/L

Q: The SLEX was designed to carry a free-flow speed of 50 kph and a capacity of 4000 veh/hr. At a certa...

A: Given, Free flow speed (uf) = 50 kph Capacity (qc) = 4000 veh/hr Flow rate (q) = 3600 veh/hr

Q: re important on designing buildings and structures. minimum of 15 sentences)

A: Codes and Regulations are important on designing buildings and structures- to ensure the structures ...

Q: A catchment with an area A = 85 km^2, has four rainfall gauges (P1 – P4) according to the figure. Us...

Q: Compute the total elongation caused by an axial load of 147 kN applied to a square bar, tapering fro...

Q: In the figure shown, the initial velocity is 145 ft/s. Solve for "d". Vo 25° 5° B

A: In the figure shown, the initial velocity is 145 ft/s. Solve for "d".

Q: The block in the figure below weighs 500 lb and the coefficient of friction between the block and th...

A: Equate forces on downward and upward direction.

Q: n relation to occupational health and safety, explain, using an example in each case, the meaning of...

Q: One of four monthly-read rain gauges on a catchment area develops a fault in a month when the other ...

Q: The Brinell's hardness number (B.H.N.) is expressed as P P (a) (b) TD D-VD²-d² TD D+yD²- VD²-a² P P ...

Q: h6 mm t (s) for 10L t (s) for 10L t (s) for 10L 55.25 V L/s 10.184 i h1 mm h2 mm h3 mm h4 mm h5 mm 5...

Q: Given a proposed six-story (12 meters by 18 meters) City Library which is to be constructed in the P...

A: Concrete is very strong in compression and also quite strong in shear, however, the combination of v...

Q: Which of the following statements is INCORRECT? O During dry periods, surface cracks that develop on...

A: Infiltration is the process by which water on the ground surface enters into the soil.

Q: MN

Q: 1. (e) One of the limitations of extending axis translation technique for measuring negative pore wa...

A: Note- Hi! Thank you for the question As per the honor code, We’ll answer the first question since th...

Q: SITUATION. The suspended load exerts a force F=800lbs at A and bar OA weighs 300 lb. Assume that the...

Q: SITUATION 1 Built-up column 10m long consists of W350X90 with two plates welded to form a box sectio...

A: NOTE: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question...

Q: A water column in a glass tube is used to measure the pressure in a pipe. The tube is 14 in.(6.35 mm...

Q: Aluminum Bronze Steel 2P 3P 4P – 0.6 m–→- - 1.0 m -0.8 m FIG. P2.16 compound bar consisting of bronz...

Q: (b) Which one of the following soils will have a higher volumetric water content at a suction value ...

Q: 1. For a given month a 300-acre lake has 15 cfs of inflow, 13 cfs of outflow, and a total storage in...

Q: Estimate the lag time (hr) for the following watershed: Hydraulic length (km) - 3.04 Curve number 60...

A: Given data:Hydraulic length(L)=3.04 km=9973.753 ft.Curve number(CN)=60 Average land slope(S)=1.1%

Q: 3. In 1997, Upper Grand watershed near Maputi, Bukidnon with an area of 4350 sq.km received 77.7 cm ...

Q: A steel cylinder with 400 mm outside diameter and wall thickness of 25 mm is filled with concrete an...

Q: In accordance to NSCP 2010, the calculation of the required strength U shall be at least equal to th...

A: Factored moment: While designing a structure the prime motive must be the safety of the structure. I...

Q: Based on the figure given, determine the removal efficiency of the settling column if the overflow r...

A: GIVEN OVER FLOW RATE SO ACORDING TO THAT PLOT A GRAPH

Q: Discuss the properties of concrete

Q: Problem 2: Using any method, find the ff. when E and I 100 GPa 100x10^6 mm^4 Location and magnitude ...

Q: Draw the axial force, shear and moment diagram of the figure shown.

A: If a load is applied to the structure along the length or perpendicular to the cross-section of the ...

Q: Find the minors of every element of the following matrices: For part (a): 1 3 -2] A = 4 -3 4 -1.

A: To calculate the minors of every element of the given matrix. Given, A= 1 3 -2 0 5 4...

Q: Determine the structure if it is determinate or indeterminate and if indeterminate. What is the degr...

A: Consider the figure,

Q: A soil has the following soil properties for use in the Green- Ampt equation: n = 0.464 K = 1.5 in/h...

Q: SAMPLE PROBLEM NO. 4 For the continuous beam shown, determine the values of the moments over the sup...

Q: 3 m 2 m P = 50 kN Area (mm2) length E 70 Gpa 200 Gpa Aluminum 500 4 m Steel 300 3 m Aluminum Steel

Q: 2.) For the given beam ABCD, determine the following: a. The Shear and Moment Diagram of the beam AB...

Q: steel bar sizes and concrete mixtures

A: Rcc (reinforced cement concrete) has proved to be a durable,strong and economical construction mater...

Q: Mention 5 examples of composite materials and their application in everyday life.

Q: The following offsets were taken from a chain line to an irregular boundary line at an interval of 1...

A: Given data: 0, 2.5, 3.5, 5, 4.6, 3.2,0 interval =10m

Q: P = 80kN 50mm 25mm A 30° A P.

Q: The spacing of the cars moving along the same lane of an expressway is 40 m center to center. If the...

A: Given data in question Spacing between center to center cars Average velocity To find out Volume ...

Q: ow the amount of strain gages effect your measurement read ir answer with calculation and show the l...

A: (2) we know that change in resiatance in strain gage ΔR = K. RE Nos we Will draw circuit diagra...

Concept explainers

Highway Drainage

Highway drainage is the process of extracting and regulating the excess surface water on the pavement by giving the desired slope. The construction of a highway drain helps to divert the water present on the surface, and sub-grade by the means of slope. Highway drainage systems are a necessary part of smooth functioning of traffic, since the highway drainage systems provide proper disposal of unwanted substances from the highways.

Question

PROBLEM 4
A standpipe with an open top has a diameter of 2.5m and a wall thickness of
22mm. What level of water from the bottom will result to a hoop stress of 15MPA of the
standpipe?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Given Data

VIEW

Step 2 solution

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q1-B/ The wall thickness of a 4-ft-ouside diameter spherical tank is 5/16 in. Calculate theallowable internal pressure if the stress is limited to 8000 psi.
Water is flowing in a 2m deep rectangular aqueduct, with a measured speed of 2m/s at the surface. Assuming the side walls of the channel are far enough away to have negligible impact, what is the shear stress 1m deep in the middle of the channel?
2)1 Design the reinforced concrete wall shown if f. = 4000 psi and f, = 60,000 psi. V = 300k hy = 12'0" b =12'0"
10.37 FLUS Water (20°C) flows in a 16-cm cast-iron pipe at a rate of 0.1 m/s. For these conditions, determine or estimate the following: a. Reynolds number b. Friction factor f (use Swamee-Jain Eq. (10.39) in §10.6.) c. Shear stress at the wall, To
What size pipe will maintain shear stress at the wall of 0.624 psf when water flows through 300 ft of the pipe causing a lost head of 20.0 ft?
A vertical circular gate is 1m in diameter is immersed in a liquid of specific gravity of 1.4. The top of the gate is 2.5m below the surface of the liquid. Determine the horizontal force at the bottom required to keep the gate closed if it is hinged at the top. SHOW COMPLETE SOLUTION. NEED ASAP. THANK YOU
What will be the nature of surface of pipe if the flow of water is taking place having roughness size (k) = 0.10mm, yields an average shear stress at pipe boundary To 250N/m², take v = 10-6m²/sec A Hydrodynamically smooth B Hydrodynamically rough C In transition zone D Data insufficient II
3-A water tank diameter ard 1am high. if the tark is to be is 10m in completely filled, det. the mini mun thickness 4 the tamk plating if the SHress is imited to ya mPa, Twater density wayer,=
Calculate the total stress in the given beam due to prestress only. A rectangular beam 200 x 300 mm is prestressed with 15-6 mm diameter wires located at 65 mm from the beam soffit and 2-6 mm diameter wires located 25 mm from the top of the beam. The prestress is 1000 MPa with a length of 8 meters.
Situation 5 Steel pipe having the diameter of 1 m. carries water under the head of 300meters of water. 14. Compute the wall thickness of steel pipe needed to resists the static pressure if the allowable working stress for steel pipe is 12 MPa.
Q1/ Desgin graphically an intermediate casing (11.75-in, set at 6000 ft. Hole diameter26-in. Data given as: Minimum pore pressure above 6000 ft=8.6 ppg.Maximum pore pressure above 6000 ft=9.5 ppg. Mud weight in which casing to be run = pressure gradient at 11.75-in shoe =16 ppg. Expected gas gradient = 0.1 psi/ft.Design factors for burst = 1.1, and for collapse 1.0. Note , Use graph paper for design. -11.0 ppg. Depth to the next 12.25-in hole = 10000 ft.Fracture %3D %3D
5. A 30 cm radius Cast iron main leads from a reservoir whose water surface is at EL. 1590m. In the heart of the city the main, below ground level, is at EL. 1410m. (a) What is the net pressure (b) Assuming static conditions, what is the stress in the pipe wall if the wall thickness is 12.00 mm and the external soil pressure is 250 kPa?6. A continuous wood stave pipe is 2.5 m in diameter and is in service under a head of 30.0 m of water. The staves are secure by means of round 25 mm steel hoops with an allowable stress of 105 MPa. Fine the maximum snarings of the hoops to safely secure the nine.