Problem 3. A simplified Rankine cycle and some data are given in the figure below. a. Show the process in a TS diagram b. Calculate the rate of heat addition (Qµ) to the boiler. c. Calculate Wpump- d. Calculate |WNet|- e. Determine the thermal efficiency (n2)

Problem 3. A simplified Rankine cycle and some data are given in the figure below. a. Show the process in a TS diagram b. Calculate the rate of heat addition (Qµ) to the boiler. c. Calculate Wpump- d. Calculate |WNet|- e. Determine the thermal efficiency (n2)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A reheat cycle with two stages of reheating is executed, with steam expanding initially from 202.65 and 540 deg. C. The two reheater pressures are 40 bar and 10 bar, and steam leaves each reheater at 540 deg. C. Condensation occurs at 60 deg. C. Sketch the Ts - diagram. For an ideal cycle, find Qa and e. For the engine operating between the same conditions compute W and e. For a 362, 500 kg/h steam and 100 MW generator output at 94% efficiency, for actual engine, find combined thermal efficiency and combined heat rate and combined engine efficiency and quality of the actual exhaust steam. (3 decimal places in final answer pls)
I need correct answer in 20 minutes please Find the cycle efficiency and specific steam consumption of a reheat cycle (Fig. 2.7a) operating between pressures of 3 MPa and 0.004 MPa, with superheat temp of 450 °C. Assume that the first expansion is carried out to the point where the steam is dry saturated and then the steam is reheated to the original superheat temp. The feed pump term may be neglected Boiler Reheater a High-P turbine. P = Ps= Preheal Pump Condenser Low-P turbine Figure (2.7 a) High-pressure turbine Reheating Low-pressure turbine
A simplified Rankine cycle and some data are given in the figure below.a. Show the process in a TS diagramb. Calculate the rate of heat addition (Q.H) to the boiler.c. Calculate ?w????.d. Calculate |WNet|.e. Determine the thermal efficiency (n?)
The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam flow rate = 16.3846 kg/sec of steam when the steam at the beginning of expansion is at 119.6 deg SH and 4.0 Mpaa. Draw the TS and equipment diagrams for the ideal and actual case and find for the following for the ideal case: PV and TS diagrams of the cycle showing ideal and actual process lines Heat rejected at condenser (KJ/sec). Ans.____________________________ Mass of cooling water in kg/sec if cp H2O = 4.18 KJ/kg-K, and inlet temp of water to condenser = 20 deg C, outlet temp is 35 deg C. Ans.___________________________
In a steam power plant, saturated steam at a pressure of 400 psia enters the turbine. The condenser pressure is 1 psia. Find the ideal Rankine cycle and the maximum thermal efficiency. [Ans: 33% and 38%]
The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam flow rate = 1 kg/sec of steam when the steam at the beginning of expansion is at 119.6 deg SH and 4.0 Mpaa. Draw the TS and equipment diagrams for the ideal and actual case and find for the following for the ideal case: Ideal turbine work (KW). Ans.____________________________ Heat rejected at condenser (KJ/sec). Ans.____________________________ Mass of cooling water in kg/sec if cp H2O = 4.18 KJ/kg-K, and inlet temp of water to condenser = 20 deg C, outlet temp is 35 deg C. Ans.____________________________ Pump work in KW. Ans.___________________________
I'll leave a thumbs up if you ans the following. Determine the following: a. The fuel flow rate in kg/sec b. Cooling water flow rate in kg/min c. Assume an ideal cycle with pump efficiency = 80% and turbine efficiency = 85%, find the quality of steam entering the condenser
The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam flow rate = 1 kg/sec of steam when the steam at the beginning of expansion is at 119.6 deg SH and 4.0 Mpaa. Draw the TS and equipment diagrams for the ideal and actual case and find for the following for the ideal case: Pump work in KW. Ans. Ideal heat rate in KJ/KW-hr. Ans. Rankine engine efficiency (%). Ans. Cycle thermal efficiency ( %). Ans
Solve neatly and draw diagrams. write neatly An regenerative engine receives 68,000 kg/hr of steam having 1 open heater which receives 15,400 kg/h of Bled steam. If the condenser pressure is 0.008 MPa and the open heater pressure is 0.98 MPa find the enthalpy a) at the heater entrance, b) condenser entrance.
1. Steam is generated at 4.20 MPa and 460°C and condensation occurs at 0.105MP.. a. For a rankine engine operating between these limits compute the thermal efficiency and the heat rate. b. Considering that a Rankine cycle occurs between the same limits, determine Q.. Q,, w. and e C. What mass flow rate is required for a net output of 35,000 kW?
Homework-2 Compute the themal e fficiency of an ideal Ran kine cycle for which the steam leavea the boiler as Saturated Vapor at 30 bars. The turbine-outlet Conditions is Be1 bar. Determine the mass floo rate of the steam in kg/hr, net Power output of the cycle is 50000 Sehematic ond given data are: 1f the kw. The TI= 5002 P 3०bars %3D 9in (saturated) vapour 30 bars 2 PR =0-1 bar 4 Pa=30 bas o-1 bar +4 Tout 3 (Saturated liquid) Wp ( Simple Ideal Power cycle) (T.S. diagram e)
Step 2) Find the optimurn value of the reheat pressure in order to achieve the highest efficiency in the domain of the admissible values of the steam quality. For that keep the turbine infet conditions as given. Cycle 2- Idcal Rankine Cycle With Reheating Pick out four different values of the reheat pressure within the interval (0.1 to 0.4) x inlet pressure to high pressure turbine, to find the proper reheat pressure. Procced as follows: Case I. Keep the turbine exit pressure the same as the one obtained in step 1 for the highest efficieney at x= 0.87. Change the reheat pressure to obtain the best efficiency. Casc II. Keep the reheat pressure obtained in Case I fixed and change the turbine exit pressure to obtain efficiercy corresponding to x = 0.87 TEM_1 ITEM 1 CONT KW PSI 5 35 190,000 1700