Problem 1: The assembly below will be used for each problem. Lengths, diameters, and materials are provided. If the temperature when this system was assembled was 74F, what would be the stress in each cylinder at a temperature of 40F? Problem 2: If the fixed support at D were removed and the temperature change did not occur, how far would pointD move if a 400 lb tension load was applied at the center of each cylinder? (Hint: what sections would you break up the assembly into to find the Normal forces?) Problem 3: Based on the results from problem 2 and the sections specified in your solution, how much would the diameter of each section shrink from the loads applied? (Hint: Look at Poisson's ratio for each of the sections listed. 304 Stainless steel 2014-T6 Aluminum C 86100 Bronze 12 in. 8 in. C 4 in. B 3 ft 6 ft 4 ft

Problem 1: The assembly below will be used for each problem. Lengths, diameters, and materials are provided. If the temperature when this system was assembled was 74F, what would be the stress in each cylinder at a temperature of 40F? Problem 2: If the fixed support at D were removed and the temperature change did not occur, how far would pointD move if a 400 lb tension load was applied at the center of each cylinder? (Hint: what sections would you break up the assembly into to find the Normal forces?) Problem 3: Based on the results from problem 2 and the sections specified in your solution, how much would the diameter of each section shrink from the loads applied? (Hint: Look at Poisson's ratio for each of the sections listed. 304 Stainless steel 2014-T6 Aluminum C 86100 Bronze 12 in. 8 in. C 4 in. B 3 ft 6 ft 4 ft

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

4) Explain and illustrate variations of normal stresses everywhere on the bar and state why it is significant to look at the normal stress variations from a design perspective? P P
Item 2 The gas storage tank is fabricated by bolting together two half cylindrical thin shells and two hemispherical shells as shown. The tank is designed to withstand a pressure of 3 MPa. The tank and the 25 mm diameter bolts are made from material having an allowable normal stress of 160 MPa and 256 MPa, respectively. The tank has an inner diameter of 4 m. Figure 1 of 1 Determine the required minimum thickness of the cylindrical shell. (Figure 1) Express your answer with the appropriate units. te = 37.5 mm Submit Correct Part B Determine the required minimum thickness of the hemispherical shell. Express your answer with the appropriate units. t₂ = 18.8 mm Submit Correct Part C My Answers Give Up ng = My Answers Give Up Determine the minimum required number of bolts for each hemispherical cap. IVD ΑΣΦ ↓↑ vec ? bolts
3. Find the thickness of a cast iron cylinder 250 mm in diameter to carry a pressure of 0.7 N/mm2. Take maximum tensile stress for cast iron as 14 MPa. [Ans. 6.25 mm]
The gas storage tank is fabricated by bolting together two half cylindrical thin shells and two hemispherical shells as shown. The tank is designed to withstand a pressure of 2.1 MPa. The tank and the 25-mm-diameter bolts are made from material having an allowable normal stress of 150 MPa and 250 MPa, respectively. The tank has an inner diameter of 4 m. Part A Determine the required minimum thickness of the cylindrical shell. Express your answer to three significant figures and include the appropriate units. ANSWER: tc = Part B Determine the required minimum thickness of the hemispherical shell. Q Tap image to zoom Express your answer to three significant figures and include the appropriate units. ANSWER: th =
A compressed gas cylinder for use in mechanical engineering laboratory has an internal gage pressure of 8 Mpa at the time of delivery. the outside diameter of the cylinder is 30 cm. if the steel has an allowable stress of 90 Mpa. what is the required thickness of the wall in centimeter? is it considered a thin walled? [chacking: thickness/inside raduis
8 KN 2m 3m 6KN. Am 3m, 3m A B 2m 6KN cross-Section 300mm 150mm Only considering stresses that are normal to the cross-sections you're designing. Where omax is the maximum value of stress developing in the cross-sections. Calculate omax
Situation 1: A rigid bar ABC weighs 10 kN/m. The compressive stress of the copper bar is 20 MPa. Answer the following questions: 3m B 2 m Copper L=3m A = 1500 mm² Brass C L = 2 m A = 1200 mm² A. What is the stress of the brass bar? Indicate if it will experience tension (T) or compression (C) (MPa) B. What is the minimum required diameter of the pin at A assuming that the pin connection is in double shear? Consider the allowable shearing stress of the pin as 15 MPa. Round your answer in a multiple of 5. (mm)
A steel tube with 3cm outside diameter, 0.25cm thick, and 4m long is covered and lined throughout with copper tubes 0.20cm thick. The three tubes are joined together at their ends. What is the maximum compressive load that can be applied to the top such that the total deformation does not exceed 0.50mm? Esteel = 200 GPa & Ecopper = 110 GPa.
1. The assembly has the diameters and material makeup indicated. If it fits securely between its fixed supports when the temperature is T; = 70°F, determine the average normal stress in each material when the temperature reaches T2 = 130°F. 304 Stainless steel - 2014-T6 Aluminum -C 86100 Bronze A 12 in. 8 in. D C 4 in. -4 ft- 6 ft- 3 ft
An aluminum rod is rigidly attached between a steel rod and a bronze as shown. Axial loads are applied at the positions indicated. Find the stress of each rod in MPa. Steel Aluminum Bronze A- 500mm? A = 400mm? A - 200mm 40KN 10KN 20KN 2.5m 2.0m 1.5m
A plate of 150 mm width and 20 mm thick is welded to another plate by fillet weld as shown in the figure. The size of the weld is 12 mm throughout. Compute the average shear stress produced in the weld for the full strength of the plate if the allowable stress is 150 N/mm². 70.72 mm 70.72 mm 14 150 mm 150 mm ► 60 mm dia 150 mm
Problem 3 The gas storage tank is fabricated by bolting together two half cylindrical thin shells and two hemispherical shells as shown. The tank is designed to withstand a pressure of 2.1 MPa. The tank and the 25-mm-diameter bolts are made from material having an allowable normal stress of 150 MPa and 250 MPa, respectively. The tank has an inner diameter of 4 m. Part A Determine the required minimum thickness of the cylindrical shell. Express your answer to three significant figures and include the appropriate units. ANSWER: te = 28.0 mm Part B Correct Determine the required minimum thickness of the hemispherical shell. Express your answer to three significant figures and include the appropriate units. ANSWER: th=14.0 mm Part C Correct Determine the minimum required number of longitudinal bolts per meter length at each side of the cylindrical shell. Express your answer as an integer. ANSWER: nc =