Problem 1 A tank is being considered to mix a chocolate solution that has a 8.0 kW motor. This baffled tank is 1.25 m in diameter and 1.25 m high with a HE-3 impeller that is 0.36 m from the bottom of the tank. In order to sufficiently mix the chocolate solution, an agitation speed of 810 rpm will be needed. The motor efficiency is 70%. Is the motor adequate to mix the chocolate solution?

Problem 1 A tank is being considered to mix a chocolate solution that has a 8.0 kW motor. This baffled tank is 1.25 m in diameter and 1.25 m high with a HE-3 impeller that is 0.36 m from the bottom of the tank. In order to sufficiently mix the chocolate solution, an agitation speed of 810 rpm will be needed. The motor efficiency is 70%. Is the motor adequate to mix the chocolate solution?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The value of enthalpy at point 1 is ( hi2 ?) The value of enthalpy at point 3 is (h3?) The value of enthalpy at point 4 is (h4?) The value of steam mass flow rate in kg/s is The rate of heat supplied is
Pls solve accurate and fast A 1-kg steam-water mixture at 1.0 MPa is contained in an inflexible tank. Heat is added until the pressure rises to 3.5 MPa and the temperature to 400: Determine the heat added
Q112kgof water at 25° Mixed with 30lit of water ats4c.calculate the tempature of the Mixtuce Neglect Q tosses to the Suvroundings and cousider
The pressure of the air in a starting vessel is 40 bar and the temperature is 24°C. If a fire in the vicinity causes the temperature to rise to 65 °C. Neglect anyincrease in the volume of the vessel which is 5 liters. determine the: a. work nonflow and heat transferred
2. One cubic foot of oxygen at 100°F and 15 psia is compressed adiabatically to 0.4 ft. What then, are the temperature and pressure of the gas. If the process had been isothermal, what would the temperature and pressure have been?
e) Calculate the energy required to fully evaporate 10 kg of liquid water at a constant pressure of 300 kPa.
Liquid water at 35 ºF is fed to a boiler operating at 10 bars and is converted at constant pressureto saturated steam. The steam is produced at a steady state flow rate of 600 lbm/hr. Assume thatthe kinetic energy of the liquid entering the boiler is negligible, and that the steam is dischargedfrom the boiler through a 1 ft pipe.a. Calculate ∆Ĥ (in units of Btu/lbm) for this process.b. Calculate the heat input (Btu/hr) to meet the needed saturated steam production rate.
What is the temperature in Rankine of 2 liters of water at 30 deg C after 500 cal of heat have been added?
Name the diagnostic criteria in Cyclic Voltammetry for an reversible process
Please help me answer this problem ASAP! Thank you.
Q10/ Calculate specific volumes for Nitrogen: 120 K, 60% quality *
Evaporator, single effect is used to upgrade the concentrate 8000 kg/h of tomato juice than 5% solids the total to 30% solids total. Juice enters the Evaporator at 20 °C. The Evaporator is operated with Steam (quality 80%) in 143.27 kPa. The condition of vacuum in the Evaporator allow the juice to a boil on the 75 °C. The hot kind of material dilute is 4.1 kJ/(kg °C) and the product the concentrate is a 3.1 kJ/(kg °C). Count (a) the Rate of the needs of steam = kg/h. b. The economic steam if the temperature is condensate is released at 75 °C. = (kg water evaporated/kg of steam)