Problem 08.043 Determine principal stresses in a shaft under combined loadings. The steel pipe AB has a 78-mm outer diameter and a 5-mm wall thickness. Knowing that arm CDE is rigidly attached to the pipe, determine the principal stresses and the maximum shearing stress at point K. 120mm 3 AN 120 m The principal stresses are max The maximum shearing stress is 19AN 150 mm MPa and Omin MPa. MPa.

Problem 08.043 Determine principal stresses in a shaft under combined loadings. The steel pipe AB has a 78-mm outer diameter and a 5-mm wall thickness. Knowing that arm CDE is rigidly attached to the pipe, determine the principal stresses and the maximum shearing stress at point K. 120mm 3 AN 120 m The principal stresses are max The maximum shearing stress is 19AN 150 mm MPa and Omin MPa. MPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A torque of 1.4KNm and two forces of 10kN and 12kN are applied to the top of a 65mm diameter solid steel post. Determine the principal stresses and the maximum shear stress at point H and point K.
A 400-lb vertical force is applied at D to a gear attached to the solid 1-in. diameter shaft AB. Determine the principal stresses and the max-imum shearing stress at point H located as shown on top of the shaft
Forces are applied at points A and B of the solid cast-iron bracket shown. The bracket has a diameter of 0.8 in. Take P = 2000 lb. 2.5 in. 600 lb max The principal stresses are: ksi 1 in. Determine the principal stresses and the maximum shearing stress at point H. (Round the final answers to two decimal places. Input the answers with the appropriate sign.) A 3.5 in Omin ksi The maximum shearing stress is ksi,
A pressure vessel of 225-mm inner diameter and 6-mm wall thickness is fabricated from a 1.2 m section of spirally welded pipe AB and is equipped with two rigid end plates. The gage pressure inside the vessel is 2 MPa, and 45-kN centric axial forces P and P' are applied to the end plates. P' A 1.2 m 35⁰ B Determine the shearing stress parallel to the weld. The shearing stress parallel to the weld is P MPa.
A force Q of magnitude 3kips is applied on the machine element AB of uniform thickness 0.8. Determine the normal and shearing stresses at point a
Determine the maximum absolute shear stress for the state of stress at a point shown. a. b. 0 50.0 40 ksi 30 ksi 40 ksi C. 100.0 d. Answer is not among the choices
The steel pipe AB has a 72-mm outer diameter and a 5-mm wall thickness. Knowing that the arm CDE is rigidly attached to the pipe and R= 3.4 kN, determine the principal stresses, principal planes, and the maximum shearing stress at point H. (Round the final answers to two decimal places.) R B D 9 kN 120 mm 150 mm 120 mm E The principal stresses at point Hare MPа MPа Ob = The principal planes at point H are Ob The maximum shearing stress at point His MРа.
HWs. 1. The grains of wood in the board make an angle of 20° with the horizontal as shown. Using Mohr's circle, determine the normal and shear stresses that act perpendicular and parallel to the grains if the board is subjected to an axial load of 250 N. -300 mm 60 mm 250 N 250 N+ 20 25 mm 2. The post has a square cross-sectional area. If it is fixed supported at its base and a horizontal force is applied at its end as shown, determine (a) the maximum in-plane shear stress developed at A and (b) the principal stresses at A. 18 in. 3. Determine the principal stress, the maximum in-plane shear stress, and average normal stress. Specify the orientation of the clement in cach case. 20 MPa 8O MPa 30 MP.
A thin-walled cylinder has an internal diameter of 1200 mm and has walls 1.2 mm thick. It is subjected to an internal pressure of 0.7 N/mm² and a torque, about its longitudinal axis, of 500 kNm. Determine the principal stresses at a point in the wall of the cylinder and also the maximum shear stress. Ans. 466.4 N/mm², 58.6 N/mm², 203.9 N/mm².
In the hanger shown the upper portion of link ABC is 9-mm thick and the lower portions are each 6-mm thick. Epoxy resin is used to bond the upper and lower portions together at B. The pin at A is of 9-mm diameter while a 6-mm-diameter pin is used at C. Determine (a) the shearing stress in pin A. (b) the shearing stress in pin C, (c) the largest normal stress in link ABC, (d) the average shearing stress on the bonded surfaces at B, (e) the bearing stress in the link at C. 30 mm 150 mm 40 mm 170 mm 240 mm 2400 N 120 m
Determine the principal stresses andmaximum in-plane shear stress of given stresselement.
2. The puncher is to drive a 25 mm diameter hole to a steel plate. If the allowable axial stress of the puncher is limited to 101.85 MPa, determine the thickness (t) of the steel plate. The maximum shear stress of the steel plate is 50MPa.