Subject: Problem 03.142 - Hollow thin-walled shaft loaded by torsionA hollow member having the cross section shown is formed from sheet metal of 2-mm thickness. Knowing that the shearing stressmust not exceed 3.5 MPa, determine the largest torque that can be applied to the member.50 m-50 min20 mmThe largest torque that can be applied isN-m.

Answered: Image /qna-images/answer/f566ed5d-cd54-4ba4-928a-0880befe7584.jpg

Problem 03.142 Hollow A hollow member having the cross section shown is formed from sheet metal of 2-mm thickness. Knowing the must not exceed 3.5 MPa, determine the largest torque that can be applied to the member. 50 mm- 50 mm P 20mm 20 mm

Problem 03.142 Hollow A hollow member having the cross section shown is formed from sheet metal of 2-mm thickness. Knowing the must not exceed 3.5 MPa, determine the largest torque that can be applied to the member. 50 mm- 50 mm P 20mm 20 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Two distances of 20 rn and 100 m were accurately measured out with the help of a tacheometer and the…

Q: (a) ● The initial rate of infiltration of a watershed is estimated as 2.1 in/hr, the final capacity…

A: Initial infiltration rate (fo) = 2.1 in./hr Final infiltration rate (fc) = 0.2 in./hr Time…

Q: 2. The screw of the small press has a mean diameter of 25 mm and has a single square thread with a…

Q: Find the check value from the following levelling values: Station 1: BS 2.345, IS 2.33, FS 3.2,…

Q: Slab and Shear Design 1. Determine the required thickness and spacing of reinforcement for a 6.00m X…

Q: Figure 1 F 三 7m

Q: How are forces between the tape and strips similar to those of magnetism?

A: The forces between a strip of adhesive tape and a surface are primarily due to intermolecular forces…

Q: SOLVE THIS A stream of 150 litres per second was delivered from a canal and 110 litres per second…

A: Runoff loss in field =445 m3 Effective depth of root zone=1.5 m Available water holding capacity…

Q: (b) the bending stress at point H. Tensile stress is positive, while compressive stress is nega (c)…

Q: a) Using Macauley's Method, calculate a general expression in terms of Young's Modulus, E, and…

A: Find: Macauley's method (a) Expression for deflection (b) Deflection at 1.1 m from left hand side…

Q: 1 For the square foundation below determine: a) ultimate settlement and b) settlement after 140 days…

A: Ultimate Settlement=Sult=0.126 ft Settlement after 140 days=S140=0.087 ft Saturated unit weight of…

Q: Current Attempt in Progress * Your answer is incorrect. A composite beam is made of two brass [E =…

Q: a) What is the maximum load P that the beam can support without the columns buckling? b) How far…

A: a) Max load P on Beam without Buckling of columns b) Location 'd' of Load P from A to Avoid…

Q: Oil flows at a flow rate of 0.030 (m³/s) in two pipes Connected in Series upwards from point No. (1)…

A: Flow rate, Q = 0.03 m3/s Length , L1 = 700 Length, L2 = 1 km or 1000m

Q: Figure 1. Figure 2. Figure 3. => Explain the differences in the patterns in terms of the hydraulic…

A: A feature of porous substances, such as soils and rocks, known as hydraulic conductivity explains…

Q: A trapezoidal channel made of unfinished concrete has a bottom slope of 1°, a base width of 5 m, and…

A: Given: →The bottom slope is 1°. →The base width is 5 m. →The surface slope is 1:1. →The flow rate…

Q: Question 2: For the RC beam shown in Figure (1), draw the bending moment diagram and sketch the…

A: The loading diagram is shown below.

Q: 4. The beam shown supports the load shown, determine max flexural stress developed and 200mm the max…

Q: determine:the support reactions, momeents in the structure (the positive * signs correspond to…

A: A truss is given with a point load of 30kN acting downwards at C. The truss is hinge supported at A…

Q: A torque of 600 N-m is applied to a rectangular section shown in the figure. Determine the wall…

A: Torque applied on rectangular section = 600 = 600000 N.mm Allowed Shear stress = 60 MPa

Q: A composite beam is fabricated by bolting two 3.8-in.-wide by 9-in-deep timber planks to the sides…

A: Es = 31200 ksi Et = 1620 ksi Determine a. Maximum bending stress in timber and steel if P = 3.3…

Q: In the figure, he, hr, z and the measured slope length I were 5.65 ft, 5.38 ft, 96° 18' 56", and…

A: L=403.62ft z=96o18'56"

Q: 1) Determine time of concentration, tc, for use in the NRCS Method for a drainage basin located near…

A: Overland Flow: average grass, 100' long, 1.6% average slopeShallow Concentrated Flow: 680' long.…

Q: From a topographic mapthe areas enclosed by contour lines for a proposed dam are given below Contour…

A: Determine the volume of impounded water (V), using trapezoidal formula.

Q: 10 The annual rainfall at a place for a period of 30 years is given below. Draw the rainfall…

A: Given: Year Rainfall (cm) 1951 31.6 1952 30.1 1953 29.8 1954 39.9 1955 37.8 1956 31.3…

Q: In concrete terms, how does one go about carrying out such a check?

A: To carry out a check, you need to follow these steps: 1. Determine the purpose of the check:…

Q: 1.20 If the specific volume of a gas is 360 ft³/slug, what is its specific weight?

A: Specific volume of the gas, Vs=360 ft3slug.

Q: 2) Compute the peak runoff, qp, using the NRCS Methbd for a 100 year storm for a drainage basin…

A: Curve Number= 68 Time of concentration= 2.35 hr

Q: Experimental results show that in EBW the penetration depth of the weld decreases as the welding…

A: EBW stands for Electron Beam Welding, which is a high energy welding process that uses an electron…

Q: Please explain how you got the location of the resultant, how did you take the moment of each area,…

Q: Problem 24.15 Assignment For a highway curve with Da = 5°00', I = 20°30', and Pl station = 63 +25.53…

A: Given: Da = 5o I = 20o 30' PI station = 63+25.53 ft The circular curve at the full station = 100 ft…

Q: The moment of inertia of the triangular shaped area is I, = 4.17 x 10 mm. Given m= 100 mm and n =…

A: The moment of inertia of the triangular portion about the x-axis is 4.17×106 mm4 To determine the…

Q: SOLVE FOR REACTIONS, use Conjugate Beam Method

A: Given: Required : Support reactions using conjugate beam method

Q: Design a reinforced concrete square cross-section for a 7 m high column. The column, fixed at both…

A: Answer We know that average compressive stress in a column is given by 0.6*f'c Required gross…

Q: (c) Three identical gravity wall at a distance 120 m in a pattern of equilateral triangle, depth of…

Q: What is the maximum absolute shear in the following beam? Use L = 22, a = 3, b = 3, P₁ = 4, P2 = 4,…

Q: How can virtue ethics inform the practice of architecture, and what virtues are essential for…

A: A philosophical perspective known as virtue ethics emphasises the formation of moral character and…

Q: Q2) A screen is installed at a channel in the head of water treatment plant. The channel is of Im…

A: Design criteria for screens are as follows Design parameter Manually cleaned Mechanically cleaned…

Q: Derive the formula using only the basic ratios: γsat = Wsat / V w = Ww / Ws n = Vv / V γw = Ww / Vw

A: Prove the value using basic ratios:

Q: 2- The daily mean evaporation from a pan located near a lake is measured as 10 mm/day during August.…

A: E = 10 mm/day A = 5.5 km2 or 5.5 x 106 m2 Qin = 1 m3/s Qout = 500 lit/s or 0.5 m3/s

Q: A beam is subjected to equal bending moments of M₂ = 35 kip-ft. The cross-sectional dimensions are…

Q: || 21 Using rational method, rainfall intensity-duration curves and the data given in Fig. P 2.27…

Q: A beam is made of four planks glued together. Knowing that the vertical shear in the beam is V = 500…

Q: 3.5 An idealized velocity distribution is given by X y W=0 1+2t u= 2 V = 3 1+t Calculate and plot…

A: The x component of velocity,u =x1+t The y component of velocity v = y1+2t The z component of…

Q: Ysat (1 + wGs) = (1+w)GsYw

Q: The calculations and steps dont make sense at all. Can someone who actually knows the material…

A: S = 0.1 ft t = 100 days

Q: cover = 40 mm Concrete, f’c = 27 MPa Steel, fy (main bars) = 415 Mpa Steel, fyt (ties) = 275 Mpa 1.…

Q: M V Д A 5 K X 10'-0" 4" 4" Y Y 12" 12 K Ix= 1024 in ly = 640 in 4 10'-0" 1. The 'Inverted-T' cross…

Q: Problem 4 - Hydaway Lake needs to monitor the lake bottom conditions. A contract with Eagle…

A: Given: ROV and the periscope are attached as shown below and it is given that bottom of the lake is…

Q: Q2/ Three pipes are connected in series. The physical properties of the pipes are in Table below. If…

A: PA - PB = 150 kPa ZA - ZB = 5 m v = 1.02 x 10-6 m2/s

Concept explainers

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with. 

Question

Subject:

Problem 03.142 - Hollow thin-walled shaft loaded by torsion
A hollow member having the cross section shown is formed from sheet metal of 2-mm thickness. Knowing that the shearing stress
must not exceed 3.5 MPa, determine the largest torque that can be applied to the member.
50 m
-50 min
20 mm
The largest torque that can be applied is
N-m.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Determine the largest torque can be applied

VIEW

Step 2: Determine the largest torque can be applied

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
Problem 2 The rigid bar is plnned at A and held by two flexible bars at E and C. The load P Is applled at B. The two flexible bars FE and DC each have a diameter of 1 In. The flexible bars are elastic- perfectly plastic with a yleld stress equal to 20 ksl and a yleld strain of 0.001. Determine the following: The load R, at first yleld and the corresponding deflection at B, &, The ultimate load Pu and the corresponding deflection du The permanent deflection and residual stresses in each rod if the ultimate load is removed Construct P - A curve showing yield, ultimate and permanent deformation o (ksi) 1 ft E F 1 ft1 ft 20 B P e (in./in.) 0.001 1 ft D 2 ft 1 ft A
Problem 5-82 The Am1004-T61 magnesium tube is bonded to the A-36 steel rod. If a torque of T = 5 kN m is applied to end A, determine the maximum shear stress in each material. Sketch the shear stress distribution. 900 mm B 80 mm, 40 mm
A stepped shaft is as in Figure 5-13. The AB part is aluminum (G = 28GPA) and the BC part is steel (G= 84GPA). The aluminum part has a solid circular section with a diameter of 45 mm and the steel part has a circular head section with an outer diameter of 60 mm and an inner diameter of 30 mm. Find the maximum shear stress in each material and the torsion angle at B at which the torsion moment of 4000 N.m is applied. A and C terminals are rigidly connected.
1. A steel shaft is to be manufactured either as a solid circular bar or as a circular tube (Fig. 3-12). The shaft is required to transmit a torque of 1200 Nm without exceeding an allowable shear stress of 40 MPa nor an allowable rate of twist of 0.75%m. (The shear modulus of elasticity of the steel is 78 GPa.) a) Determine the required diameter d0 of the solid shaft. b) Determine the required outer diameter d2 of the hollow shaft if the thickness t of the shaft is specified as one-tenth of the outer diameter. c) Determine the ratio of diameters (that is, the ratio d2/d0) and the ratio of the weights of the hollow and solid shafts.
Reaction force Pin Retaining ring Ⓡ Force on link
A steel pipe is subjected to the 16-kN load shown below. Its outside diameter is 140 mm and its thickness is 7 mm. Consider that the yield strength of steel is 240 MPa. Analyze point H ONLY. Due to the pressure in the pipe, there is an 11.25-MPa (T) normal stress along x and a 22.50-MPa (T) normal stress along z of point H. A. Determine the internal forces and moments at the pertinent section through an FBD. B. Determine the stresses experienced by point H. Illustrate using a stress element. C. Determine the FS by MSST at point H D. Determine the von Mises equivalent stress at point H E. Determine the FS by MDET at point H 700 mm 16 KN 1,300 mm
P A B 1m E 1m 2m The simply supported beam shown has a solid rectangular cross section having beam width of 130mm and a height of 200mm. Assuming values of P = 25KN, w = 30 kN/m, and E = 5m, determine: 1) The max tensile bending stress in MPa (enter this value into D2L answer box, in MPa). Exactly where does this occur along the beam? (4 sigs) 2) The max shear stress in MPa. Exactly where does this occur along the beam? ( 4 sigs) Your Answer:
Prob 1. The rigid bar below is supported by a pin and two rods and must support a load of 100 kN is placed 3 m from A. The brass (Ebrass = 85 GPa) rod has a cross section of 30 x 30 mm and the copper (Ecopper = 120 GPa) rod 20 x 20 mm. Determine the normal stress and deflection of both bars. 1.5 m 2 m B -copper 100 kN brass- 3m 3 m E
The aluminum shaft, composed of three segments is fastened to rigid supports as A and D. Calculate the maximum shear stress in each segment when the two torques are applied.
A square plate 2 m on each side is supported by four steel tie rods 6-mm-diameter from an overhead central point as shown in the figure STRM10. The plate supports a surface load of W in kPa. The point of attachment A is 1.25 m above the plane of the plate. 1.25 m 2 m 2 m Determine the maximum load W (kPa) the tie rods can support if the allowable tensile stress on it is 450 MPa. 1) A. 8.43 С. 10.12 В. 12.83 D. 5.64 2) Determine the elongation of each steel tie rod if W = 8.5 kPa. A. 4.28 mm B. 6.46 mm C. 2.84 mm D. 3.54 mm 3) Determine the vertical displacement of the plate. A. 4.28 mm B. 6.46 mm С. 2.84 mm D. None of the above O 1A 1B 10 1D O 2A 28 O 20 O 20 О ЗА O 3B O 30 O 3D
Question 2 A compound shaft consists of copper rod of 30 mm diameter enclosed in a steel tube of external diameter 50 mm and 10 mm thick. The shaft is required to transmit a torque of 1000 Nm. Find the shear stresses developed in copper and steel, if both the shafts have equal lengths and welded to a plate at each end, so that their twists are equal. Take modulus of rigidity for steel as twice that of copper.