Please create a comparison table between the 5 common configurations of BJT amplifiers: CE fixed bias, CE voltage divider bias, CE un-bypassed emitter resistance, CC (emitter follower) and CB. For each configuration, draw the circuit, and list the 4 main quantities which are the: input impedance, output impedance, voltage gain, and current

Please create a comparison table between the 5 common configurations of BJT amplifiers: CE fixed bias, CE voltage divider bias, CE un-bypassed emitter resistance, CC (emitter follower) and CB. For each configuration, draw the circuit, and list the 4 main quantities which are the: input impedance, output impedance, voltage gain, and current

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter15: Alternating-current Circuits

Section: Chapter Questions

Problem 72CP: The two circuits shown below act as crude low-pass filters. The input voltage to the circuits is...

See similar textbooks

Similar questions

The emf of an ac source is given by v(t)=v0sint. where V0=100V and at =200rad/s . Calculate the average power output of the source if it is connected across (a) a 20F capacitor, (b) a 20-mH inductor, and (c) a 50 resistor.
Calculate the rms currents for an ac source is given by v(t)=v0sint , where V0=100V and =200rad/s when connected across (a) a 20F capacitor, (b) a 20-mH inductor, and (c) a 50 resistor.
A 700-pF capacitor is connected across an ac source with a voltage amplitude of 160 V and a frequency of 20 kHz. (a) Determine the capacitive reactance of the capacitor and the amplitude of the output current of the source. (b) If the frequency is changed to 60 Hz while keeping the voltage amplitude at 160 V, what are the capacitive reactance and the current amplitude?
Calculate the reactance of a 5.0F capacitor at (a) 60 Hz, (b) 600 Hz, and (c) 6000 Hz.
At 1000 Hz, the reactance of a 5.0-mH inductor is equal to the reactance of a particular capacitor. What is the capacitance of the capacitor?
(a) What is the resonant frequency of an RLC series circuit with R=20 , L=2.0mH , and C=4.0F (b) What is the impedance of the circuit at resonance ?
The two circuits shown below act as crude low-pass filters. The input voltage to the circuits is vin, and the output voltage is vout. (a) Show that for the capacitor circuit, voutvin=11+2R2C2 and for the inductor circuit, voutvin=RR2+2L2 (b) Slow that for low frequencies, voutvin , but for high frequencies, vout0 .
What is the impedance of a series combination of a 50resistor, a 5.0F capacitor, and a 10F capacitor at a frequency of 2.0 kHz?
For what value of the phase angle between the voltage output of an ac source and the current is the average power output of the source a maximum?
A series RLC ciruit is connected to an AC power source, as shown in the figure. Given that the voltage amplinade of the resistor VR - IR, where I is the current amplitude, and the voltage amplitude across the entire circuit Vipe- IZ, where Z- JR + (wL - is the impedance of the circuit, determine the behavior of the ratio VR/Vor s a function of the angular frequency o for the case when w > 0, where ap- 2o (fo is the natural, resonant frequency of the circuit). R C OA OE1/
A series circuit contains a resistor, a capacitor, and an inductor, connected to an A voltage source. The component values are as follows C = 0.60 µF The capacitor has a maximum safe peak voltage of 350 V, If the voltage source drives ie circuit at the resonant frequency, what is its largest possible peak voltage output to hot damage the capacitor? Hint: consider the current and impedance at resonance. R = 2.5 N L = 15 mH
An output impedance of an audio amplifier has an impedance of 500 Ω and has a mismatch with a lowimpedance 8-Ω loudspeaker. You are asked to insert an appropriate transformer to match the impedances. What turns ratio will you use, and why? Use the simplified circuit shown below.