▶ Part B Two loads, A and B, are connected in parallel across a 1-kV-rms 60-Hz line, as shown in (Figure 1). Load A consumes 10 kW with a 90 percent lagging power factor. Load B has an apparent power of 20 kVA with an 80 percent lagging power factor. Part C Find the apparent power delivered by the source. Express your answer using three significant figures. Figure 1 kV rms 60 Hz Iline apparent power = ΜΕ ΑΣΦ Η vec ? Submit RequestAnswer Request Answer 1 of 1 Part D What is the power factor seen by the source? Express your answer using three significant figures. B PF = ΜΕ ΑΣΦ Η vec Submit Request Answer ? percent VA

▶ Part B Two loads, A and B, are connected in parallel across a 1-kV-rms 60-Hz line, as shown in (Figure 1). Load A consumes 10 kW with a 90 percent lagging power factor. Load B has an apparent power of 20 kVA with an 80 percent lagging power factor. Part C Find the apparent power delivered by the source. Express your answer using three significant figures. Figure 1 kV rms 60 Hz Iline apparent power = ΜΕ ΑΣΦ Η vec ? Submit RequestAnswer Request Answer 1 of 1 Part D What is the power factor seen by the source? Express your answer using three significant figures. B PF = ΜΕ ΑΣΦ Η vec Submit Request Answer ? percent VA

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.33P: Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage...

See similar textbooks

Similar questions

In the circuit in the figure; L1 load draws 15 kVA with lagging power factor 0.6. The L2 load draws 6 kVA with a leading power factor of 0.8. According to this; What is the value of the complex power for the L2 load?
)Two complex loads Z1 and Z2 are connected in parallel and powered by a value voltage effective 7.2 kV and frequency 60 Hz. The first load has a power of 50 kVA and a factor of rear power of 0.9. The second charge has a power of 45 kW and a rear power factorof 0.91. Determine in steady state the kVAR power and the capacity required to correct the Total power factor to a value of 0.97 rear.
For the circuit given in Figure 1, a) Find the Thevenin equivalent circuit with respect to terminals a-b b) When a 5000 resistor is connected to terminal a-b, find the voltage on the resistor wwwwwwmm c) It will be connected to a-b terminals and its voltage on 5000 load will be 132 kV rms. What should be the capacitive reactance value that will increase it? wwwwwwwww d) What happens to the short-circuit current when the a-b terminals are short-circuited? 2+1202 000 m da 127/6 kV rms ob 1.5 +/902 000 w 12725 kV ms
The actual impedance of a load is 30 OHM. The per-unit impedance of the load is 0.5 pu when Base Voltage is 600 V and Base Power is O 6000 VA O 2000 VA O 4000 VA 8000 VA
The actual impedance of a load is 10 OHM. The new per-unit impedance of the load is 0.5 pu when Base Voltage is 200 V and Base Power is O 4000 VA O 8000 VA O 6000 VA O 2000 VA
Manufacturers usually specify the impedances of machines and transformers in O Percent O Per-unit O None of the options is true O Per unit or percent
The actual impedance of a load is 10 OHM. The new per-unit impedance of the load is 0.5 pu when Base Voltage is 200 V and Base Power Is O 4000 VA CO 8000 VA O 6000 VÀ O 2000 VA
Four conductors meet at a junction. the current are i1= 5sinwt, i2= 3sin(wt + 90) and i3= 2sin(wt-90). calculate the rms value of i4.
Need asap pls help. Solve for the voltages across and currents through each component. Show the complete solution and explain. The total power should be zero..
A Load of particular kVA is drawing a current which lags behind the voltage at an angle of 63.43 degrees. The operating power factor is __________ . a. 0.5958 b. 0.6122 c. 0.6511 d. 0.4472
Q2/ Find Yous for the power system all reactance on a common base. Bus 3 j0.25 j0.10 j0.25 Bus 2 j0.125 Bus 1 j0.40 j0.20 j0.10 Bus 4
Determine the rms current I as shown in figure 2. Source voltage is already in RMS value(Answer must be in polar formand should be in 4 decimal places).