NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Consider a 210-MW steam power plant that operates on a simple ideal Rankine cycle. Steam enters the turbine at 10 MPa and 500°C and is cooled in the condenser at a pressure of 15 kPa. Problem 10.019.c - Thermal efficiency of the cycle Determine the thermal efficiency of the cycle. The thermal efficiency of the cycle is %.

NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Consider a 210-MW steam power plant that operates on a simple ideal Rankine cycle. Steam enters the turbine at 10 MPa and 500°C and is cooled in the condenser at a pressure of 15 kPa. Problem 10.019.c - Thermal efficiency of the cycle Determine the thermal efficiency of the cycle. The thermal efficiency of the cycle is %.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

High-P turbine Low-P turbine Reheater O Boiler P4 = Pg = Preheat Pump Condenser The following data was given for a steam power plant operating on the ideal reheat Rankine cycle. Click Save and Submit to save and submit. Click Save All Answers to save all answers. 3-4: Inlet steam at 17.5 MPa and 600 6-1: inlet steam at a pressure of 11.16 kPa at a wetness fraction of 0.1. At state 1, the specific volume is 0.00101 m³/kg Find the specific entropy in kJ/kg at state 1 to 3 decimal places.
Steam Plant A steam power plant operates according to the Rankine cycle between a boiler pressure of 4 MPa and condenser pressure of 6.5 kPa. The steam has a temperature of 380 °C at inlet to the first turbine. It is just dry saturated on leaving this turbine for reheating to its original inlet temperature, before passing through a second turbine to the condenser. Draw a T-s diagram to illustrate the reheat cycle, neglect feed-pump terms and calculate the Rankine efficiency and specific steam consumption.
Solve neatly and write legibly. show diagrams Indicate reference used to determine the properties of water Steam enters a reheat-regenerative turbine at 6 MPa and 400 o C. After partial expansion to 1.24 MPa the steam is withdrawn and passed through a reheater until temperature is 350 o C. Steam then re-enters the turbine at 0.22 MPa where m 1 is extracted for feedwater heating. Remaining steam expands to a condenser pressure of 0.015 MPa. On the basis of 1 kg throttled steam, find:a) W and W p , b) Q A and Q R , c) thermal efficiency of the cycle and engine, d) steam rate of the cycle and engine, e) heat rate
High-P turbine Low-P turbine Reheater 4 Boiler P4 = P5 = Preheat Pump Condenser The following data was given for a steam power plant operating on the ideal reheat Rankine cycle. Click Save and Submit to save and submit. Click Save All Answers to save all answers. Rankine cycle. 3-4: Inlet steam at 17.5 MPa and 600 6-1: inlet steam at a pressure of 11.16 kPa at a wetness fraction of 0.1. At state 1, the specific volume is 0.00101 m3/kg Find the specific entropy in kJ/kg at state 3 to 3 decimal places.
High-P turbine Low-P turbine Reheater 4 Boiler P4 = P3 = Prcheat Pump Condenser The following data was given for a steam Click Save and Submit to save and submit. Click Save All Answers to save all answers. The following data was given for a steam power plant operating on the ideal reheat Rankine cycle. 3-4: Inlet steam at 17.5 MPa and 600 6-1: inlet steam at a pressure of 11.16 kPa at a wetness fraction of 0.1. At state 1, the specific volume is 0.00101 m³/kg 3 Find the dryness fraction of steam at state 6 to 1 decimal places.
1. Determine the Rankine efficiency of a condensing steam turbine operating in a Rankine cycle as follows: Steam pressure - 200 psiaSteam temperature - 1000 FExhaust pressure - 2 in Hg absoluteSteam rate - 1.5 lb/kW-hr 2. If the no. 1 problem has a thermal efficiency of 30%, how many barrels of 30 °API fuel oil will be required to produce 1000 kW-hr of power. Neglect the pump work.
High-P turbine Low-P turbine Reheater Boiler P=Ps=Paeheat Pump Condenser The following data was given for a steam power plant operating on the ideal reheat Rankine cycle. 3-4: Inlet steam at 17.5 MPa and 600 Click Save and Submit to save and submit. Click Save All Answers to save all answers. 3-4: Inlet steam at 17.5 MPa and 600 °C 6-1: inlet steam at a pressure of 11.16 kPa at a wetness fraction of 0.1. At state 1, the specific volume is 0.00101 m³/kg Calculate the specific heat input of the system in kJ/kg to 3 decimal places. 7L
The Problem: Supposedly you are a cadet engineer in a certain steam power plant that employ a reheat-regenerative ideal Rankine cycle. You are told that it will utilized one open feed heater (OFH). The condition are as follows: Steam is supplied with a condition of 2175.57 psia and 1112 °F. Also, it was measured that condenser pressure is 10 kPa. It was also observed that there are some steam is extracted from the turbine at 40 bar for closed feed water heater while the unextracted steam is reduced at 4000 kPa to 600°C. You are also reminded that the extracted steam is totally liquified in this closed feed water heater and then is pumped to 150 bar before joining with the feed water heater. Note that steam for the open feed water heater is bled from L.P. turbine at 5 bar. Determine : (i) Determine the amount of steam fraction that was extracted from the turbines (at each bled heater) (ii) What is the thermal efficiency of the system. (ii) Provide the process diagram for this problem.
52 es ! Check my work Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Consider a steam power plant that operates on a reheat Rankine cycle and has a net power output of 80 MW. Steam enters the high-pressure turbine at 10 MPa and 500°C and the low-pressure turbine at 1 MPa and 500°C. Steam leaves the condenser as a saturated liquid at a pressure of 10 kPa. The isentropic efficiency of the turbine is 82 percent and that of the pump is 95 percent. Determine the quality (or temperature, if superheated) of the steam at the turbine exit. Use steam tables. (You must provide an answer before moving on to the next part.) The temperature of the steam at the turbine exit is 109.42 °C.
1.) A steam power plant uses the ideal Reheat Rankine cycle where the steam enters the high-pressure turbine at 4 MPa and 300C. It partially expands to 600 kPa then it is reheated to the same temperature. After expanding again, it enters the condenser at 10 kPa. Sketch the schematic diagram and the TS diagram with labeled points, and solve for Qa, Qr, Wt, Wp, Wnet, thermal efficiency, and Steam rate kg 3241.70,2144.67,1101.06 4.03, 1097.03 33.84%, 3.28 k kJ kg kl, kg kWh
The net work for a given reheat Rankine cycle is 80MW. Steam at 10 MPa and 500C enters the first turbine and then, the second turbine at 1.2 MPa and 500C. Saturated liquid exits the condenser at 20 kPa. Draw the schematic and T-S diagrams. Label the points by setting point 1 at the condenser outlet, point 2 at the pump outlet, point 3 at the boiler outlet, point 4 at the reheater inlet, point 5 at the reheater outlet, and point 6 at the condenser inlet. Use 2 decimal places for the enthalpy and other energies in solving and for the final answers. For the steam quality (x) and entropy (s), use 4 decimal places in solving. For the specific volume, use 6 decimal places. IMPORTANT: USE THE STEAM TABLES FROM CENGEL'S BOOK ONLY (uploaded already in the files section). Determine the following: Enthalpy at point 2 in kJ/kg = Enthalpy at point 4 in kJ/kg = Enthalpy at point 5 in kJ/kg = Enthalpy at point 6 in kJ/kg = Thermal Efficiency in % = Heat added in kJ/kg = Heat rejected in…
Please read the problem and solve what is asked. Thanks! A steam power plant operates on the simple ideal Rankine cycle. Steam enters the turbine at 4.1 MPa. 500 degrees Celsius and is condensed in the condenser at a temperature of 40 degrees Celsius (a) Show the cycle on a T-S diagram, if the mass flow rate is 15 kg/s, determine (b) the thermal efficiency of the cycle, and (c) the net power output in MW.