Branch Circuit Calculation Questions1. A dishwasher is rated at 2400 W and 120 V, and isconsidered a non-continuous load. What is the minimumNMD90 conductor size, and the minimum and maximumrating of circuit breaker that can be used for the branchcircuit for this dishwasher? Equipment and terminations arerated at 75 °C.2. A hot water tank in a dwelling unit is rated at 5200 W and240 V. It takes the tank 1.5 – 2.5 hours to fully heat a tankof water. What is the minimum NMD90 conductor size,and the minimum and maximum rating of circuit breakerthat can be used for the branch circuit for this hot watertank? Equipment and terminations are rated at 75 °C.

Please find your answer below in step 2

Answered: NMD90 conductor size, and the minimum…

NMD90 conductor size, and the minimum and maximum rating of circuit breaker that can be used for the branch circuit for this dishwasher? Equipment and terminations are rated at 75 °C.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

h.1. In an alternating-current system, the maximum size for a copper grounding electrode conductor isA. 250 kcmil.B. 3/0.C. 500 kcmil.D. 4/0. h.2. The figure shows a fault condition in an ungrounded electrical system. Which of the following will occurbecause of the fault in this system?A. Only the overcurrent protector at Point A will trip open.B. The ground fault will heavily damage the service.C. Nothing will happen until a second ground fault occurs.D. The overcurrent protection will trip, shutting off all the line side power.
The three bus-bar conductors in an outdoor sub-station are supplied by units of post insulators. Each unit consists of a stack of 3-pin insulators fixed one on the top of the other. The voltage across the lowest insulator is 8-45 kV and that across the next is 7-25 kV. Find the bus-bar voltage of the station.
Answer all the questions 1. Draw a 6-stage cascaded voltage multiplier circuit for high voltage DC generation and explain the working principle. 2. Compare the properties of Solid insulators and liquid dielectrics? 3. Define Basic Insulation Level (BIL) in power systems and Explain the voltage - time relationship with the curve in insulation coordination. 4. What are the three protective methods for surges, explain one method. 5. What are the different types of surge diverters and explain any two methods? 6. A 12-stage impulse voltage generator has a total generator capacitance of C1. The wave front resistance equal to 15000 2 and load capacitance of 2500pF. The wave tail resistance is 30 times of wave front resistance and if rise time is 1.5 µs. Calculate (i) the value of each capacitor of the generator and (ii) the tail time of the impulse wave?
c.1. Which of the following is one of the three essential functions of an equipment grounding conductor?A. Provide an arc-fault current pathB. Establish groundingC. Establish bondingD. Ensure the system is groundedc.2. What's another name for the three-point method of Earth resistance testing?A. Fall-of-potentialB. Line surgeC. Spatial shieldingD. Leakage current c.3. If the National Electrical Code provides a requirement to ground equipment, it generally implies thatthere will be a direct connection to the Earth of a connection through a/anA. grounding electrode conductor.B. equipment grounding conductor.C. equipotential bonding conductor.D. bonding conductor.
In an outdoor substation the three bus-bar conductors are supported by units of post type insulators. Each unit consists of a stack of 3 pin type insulators fixed one on the top of the other. The voltage across the lowest insulator is 13kV and that across the next unit is 12KV. Estimate: 17. i. ratio of mutual to self-capacitance ii. the bus-bar voltage of the substation. iii. Efficiency across the string of insulators
Why Kelvin bridge is used for measurement of low resistance ____________________. a. due to a large current flow b. due to power dissipation across the circuit c. due to contact and lead resistance d. due to emf source used
Write in Briefly about circuit breaker, current transformer and voltage transformer
Load in Figure 1 needs to be connected to Mains Switch Board (MSB) using multicore PVC cable. As a maintenance engineer, you need to proposed cable size for the load, Determine the following issues. 1) Calculate current demand for the circuit. 1) Detemine suitable MCCB (Model and nominal current rating) should be used to protect the load against over-current. im Propose suitable cable size for the load in Figure 1. iv) Calculate voltage drop of the proposed cable WITHOUT consider the cable reactance and voltage drop correction due to higher cable operating temperature v) Calculate voltage drop of the proposed cable BY consider the cable reactance and voltage drop correction due to higher cable operatıng temperature vi) If the multicore PVC eable is change into 3 single core PVC cables, what the suitable cable size. All other multicore cables not available. (25 + variable x) m (A) 30 m (B) (15 + variable b) m (C) Multicore PVC cable MCCB 95 kW. (400 + variable y) V. 0.85 p.f. Load MSB…
A power generation plant connected to bulk load of high voltage industries shown in Figure Q3 has specifications given in Table Q3. Each equipment reactance is expressed in per unit on a common base of 100 MVA. a) Find the fault level for each bus bar in the generation plant. GI G2 TI Figure Q3: Single line diagram of a power generation plant Table Q3: Specifications of power system components Power System Component Voltage Rating X MVA Rating (kV) (pu) GI 50 33 0.2 G2 40 33 0.18 50 33/11 0.1 T2 40 33/11 0.1
Define the terms "load shedding" and "voltage regulation" in the context of power systems. How do these aspects impact the stability and reliability of an electrical grid?
In the circuit given in the figure, each switching element is triggered to remain in conduction at 120 degrees. Accordingly, taking into account the values given below; a) Calculate the effective value of phase current ia. ia_rms=? b) E = ? calculate. c) Calculate the average value of the current flowing through the S3 switching element. is3 _avg=? d) Calculate the effective value of the Vac voltage. Vac_rms=? e) Calculate the average value of the Vac voltage. Vac_avg%3? Ik g1) Is1 g3) LIs3 95] S1 S3 S5 E. la Ra E Ib Rb Ic 94] LIs4 Lis6 92) Rc g6) VIs2 Ra=Rb=Rc=R S4 S6 S2 E. Ra=Rb=Rc=19 Ohm loads are fed with 56 Hz frequency AC signal. The power drawn from the source is given as 3132.2 Watts. 79441 79447 9441 79441
Discuss the role of power system protection in ensuring the safety and reliability of electrical grids.