Name: Coune

Q: В TA A OB

A: For solution refer below image.

Q: 2 cosh(lnx)

A: to find: 2cosh(lnx)

Q: at direction should you paddle te

A: 21.80 Degree ( from downstream)

Q: Writing references is necessary

A: The vibration parameters are – Amplitude of vibration Acceleration, velocity, and displacement.…

Q: MPa . Assumin H/m² and Poisso hange in diamet

A: Given data  Dia of pressure vessel =650 mm Internal pressure = 14.7 Modulus of elasticity = 200 GPa…

Q: minimum cllowasle deign dianet

A: Given; A solid circular shaft needs to be designed to transmit;Torque,T=50 N-mAllowable shear…

Q: term gB(T - To) represents

A: Given: 2-D momentum equation for natural convection over a surface immersed in a quiescent fluid at…

Q: esistanc

A:

Q: e cofactor of the el

A: To find  Cofactor of element zero

Q: ocal hea

A: Local heat transfer coefficient will be at the particular on heat transfer surface it is equal to…

Q: Explain orthographic projection

A: Orthographic projection, a standard technique of representing three-dimensional objects, usually…

Q: e of 400 N is a dentical bar of noro?

A: given:E=400N

Q: "hich one of the following

A: given:

Q: ascal's law applies only to

A: given: Pascal's law applies only to

Q: Sketch the Orthographic and  auxiliary view

A:

Q: eertadi (surface an the Meck

A: Solution:- Given data:- P=700N m = 100Kg μs = 0.80μk = 0.60 Calculation:-F = FRICTION FORCE…

Q: ond ch unit of the fi e is a quarter of o manufacture

A: The given LPP will  be solved from graphical method. Subject to constraints:400x1+700x2≤10000x1+0x2…

Q: temperature is necessary fc

A: Temperature= 56.85 deg c.

Q: Explain where did 23.4 came from

A: Use linear interpolation technique to calculate saturation pressure at 20 degree Celsius.

Q: (a) the melting temperature for ic

A: the melting temperate of ice at 0.01 atm = 10C Boiling temperature of ice at 0.01 atm = 7 0C

Q: (EFD),

A: ANSWER- TRUE

Q: Evaluate:∫ds

A: From question   ∫ds = S + c Where c is Intregated constant.

Q: What is the temperature of low

A: Given; A carnot cycle is having an efficiency of;  ηcarnot=0.75  High temperature reservior;…

Q: ged at D and E.

A:

Q: Define; (a) Cut-in speed, (b) Cut-out speed, and (c) Betz limit

A: (a) Cut-in speed It is defined as a minimum speed at which the turbine starts generating…

Q: ut of tha

A:

Q: Interchangeability system is also called

A: Solution:

Q: al is the magni

A:

Q: an der Waal for I cross links.

A: In the above question all the options are incorrect Stiffness of thermosets are high

Q: Define fluied

A: A fluid is that state of matter which includes both gases and liquids.

Q: Could you please help me with my hw? Thank youu

A: Given that:  x = 3 sin 3t + 4 cos 3t   To prove :    a = - ω2x

Q: ure at 21

A: given:

Q: Its coeffi

A:

Q: nd the moghnitude

A: Given: Two force are equal R=153 Angle between one force and resultant is 30 degree To determine:…

Q: How did they get wn= sqrt 50 in the question?

A:

Q: is reduced icinal is

A:

Q: s particles which from ooh othe

A: Rigid body is a body which do not deform under the influence  of external applied load. The distance…

Q: "N" JOBS- “3" MACHINE

A: Where Machine G is - A+B=8+5=13 10+6=16 6+2=8 7+3=10 11+4=15 And Where H - B+C 5+4=9 . .

Q: OSHA stands for

A: OSHA stands for Occupational Safety and Health Administration

Q: mal condu

A:

Q: what is CAE?

A: CAE” Computer Aided Engineering” comes under FEA(Finite Element Analysis).It is used to simulate the…

Q: Types or Cran

A: There are various types of cranes are available on market on the basis of the requirement of the…

Q: ter at the d

A: Given : Diameter of jet = 2 cm = 0.02 m Area = a= πa4 Velocity = 25 m/s θ = inclination at outlet=…

Q: rope is wrapE

A:

Q: Describe with characteristics details for sink washer.

A: In plumbing, a sink washer is a kind of perforated metal strainer or cross section sifter used to…

Q: f the desc oth of cut rations

A: Chip forming ;

Q: Write 10 sentences on tooling used for compressing mini tablets

A: Given Mini tablet compressing tools To find Short note

Q: Define the term Angle of Repose

A: The slope of cut and fill at the excavation site which is measured in feet of horizontal to feet of…

Q: sketch the B.M and S.F diagrams with indicating all

A:

Q: tion.please explain prope

A:

Machining Processes and Machine Tools

Machining is represented as the process in which an excessive amount of substance is eliminated from the particular element in the form of pieces. In machining, cutting tools such as rotary tools, lathe, drill press, grinder, chop saw, welders, and many more are applied to get the desired shape. As compared to other manufacturing processes, machining is precise and versatile.