L. Load Analysis: A floor beam is used to support the 3-m width of a reinforced concrete slab having a thickness of 120 mm. The slab serves as a portion of the ceiling for the floor below and it's bottom is coated with plaster. Furthermore, a 2.75-m high, 12.5-cm thick lightweight solic concrete block wall is directly over the top flange of the beam. The cross-sectional area of the wide flange steel beam is 36,645 mm2. Determine the total dead load carried by the steel beam (expressed in kN/m).

L. Load Analysis: A floor beam is used to support the 3-m width of a reinforced concrete slab having a thickness of 120 mm. The slab serves as a portion of the ceiling for the floor below and it's bottom is coated with plaster. Furthermore, a 2.75-m high, 12.5-cm thick lightweight solic concrete block wall is directly over the top flange of the beam. The cross-sectional area of the wide flange steel beam is 36,645 mm2. Determine the total dead load carried by the steel beam (expressed in kN/m).

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3. The horizontal prestress at the centroid of a concrete beam of rectangular crosssection 120 mm and 250 mm, is 7 N/mm2 and the maximum shearing force on the beam is 70 kN. Calculate the maximum principal tensile stress. What is the minimum vertical prestress required to eliminate this principal tensile stress?
A pre-stressed concrete beam 400mm x 600mm in section has a span of 6m and is subjected to a UDL of(8+10) kN/m including the self weight of the beam. The pre-stressing tendons are located at 200mmfrom the soffit of the beam and provide an effective pre-stressing force of 960 kN. Determine the extremefiber stress in concrete at the mid span section.
2] A Prestress concrete beam 500mmx700mm in section has a span of 6.5m and is subjected to a uniformly distributed load of 14KN/m including the self-weight of the beam. The prestressing tendons which are located along the longitudinal centroid axis provide an effective prestressing force of 1360KN. Determine the extreme fiber stresses in concrete at the mid span section
A prestresed concrete T-beam shown has a simple span of 9m and to be pre-stressed with tendons located 100mm from the bottom of the beam at midspan. 1. Determine the stress due to prestressing force of 1648kN at the bottom fiber of the beam at midspan. a.37.77 b.31.98 c.22.07 d.zero 2. Determine the ratio of the pre stressing to the total uniform load if the resulting moment at midspan is zero a.43615.92 b.9.69 c.4.85 d. 1
A reinforced concrete beam has a width of 250 mm. and a total depth of 450mm. It has an effective depth of 375 mm and is reinforced with steel reinforcement having a total steel area of 1875 sq.mm. in one layer fc’ = 27.6 MPa and fy = 414.7 MPa.
2. A reinforced concrete beam having a width of 280 mm and a total depth of 600 mm isreinforced for tension at the bottom with 6 - 36 mmɸ bars placed on two layers, 4 bars onfirst layer and 2 bars on second layer. Compute the effective depth of the beam and theclear horizontal spacing between bars.
A timber beam 98 mm wide by 160 mm high is subjected to a vertical shear V = 26 kN. Determine the shearing stress developed at layer 3 only 20 mm apart from the top to bottom of the section. Answer must be in MPa
For a simply supported prestressed concrete bearn, compute the stress in the top fiber at midspan due to prestressing force and service loads after transfer. Loss of prestressing force = 20%. Properties of the beam are: Width of the bearn, b: 242 mm; Depth of the %3D beam, d: 417 mm; Concrete cover of the bearn, cc: 61 mm; Prestressing Force, P: 574 KN; Superimposed Load, w: 14 KN/m; Length of the beam, L: 9 m. Stress is in unit MPa. Write only the value of your final answer. w (including selfweight) W „P.
2.The concrete post in Fig. (a) is reinforced axiallywith four symmetrically placed steel bars, each ofcross-sectional area 900 mm2. Compute thestress in each material when the 1000-kN axialload is applied. The moduli of elasticity are 200Gpa for steel and 14 Gpa for concrete.
A 235 mm x 438 mm prestressed beam has a simple span of 6 m. The beam uses stress relieved tendons with specified tensile strength fpu = 1,368 MPa and an effective stress in prestressed reinforcement after allowable for all prestress losses fse = 750 MPa. The prestressed beam is not to be grouted after the application of the the prestress. If the area of prestress reinforcement in the tension zone is Aps = 1,140 mm2 applied 49 mm above the bottom of the beam and fe' = 31.8 MPa, determine the nominal moment of the beam.
A section of a prestressed concrete beam 150 mm x 300 mm carries a factored shear force of 110 kN and a factored bending moment of 25 kNm. The prestressing steel index is 0.4, and the effective prestress after all losses is 600 MPa. Compressive stress at centroidal axis due to prestress is 6.5 N/mm Design suitable shear reinforcement. Assume ock 35 N/mm, Op 1600 N/mm, Ap= 150 mm and cover to reinforcement is 60 mm.
A reinforced concrete beam has a width of 300 mm and effective depth of 500mm to the centroid of the tension reinforcements. Consider the steel reinforcements will be placed in a single layer arrangement. Concrete strength fc’ = 34.5 MPa. Determine the steel ratio of the section if the beam is singly reinforced with the maximum amount of steel for transition control allowed by the Code if the bars has a steel strength of fy = 345 MPa. Determine the steel ratio of the section if the beam is singly reinforced with the maximum amount of steel for tension control if the bars has a steel strength fy = 345 MPa. Determine the number of pieces of 28 mm ᴓ bars required for the section if the beam is singly reinforced with the maximum amount of steel for tension control if the bars has a steel strength fy = 415 MPa.