1. Calculate slab dead load intensity in kPa (kilo Pascal = kN/m²) in a main floor condobuilding, given the following parameters:- Allow for 0.3kPa for M&E (i.e. Parkade mechanical and electrical like for exampleducts, light fixtures etc..).Minimum allowance for partition walls as per ABC2019175mm concrete slab0.2kPa for tiling allowance (including tiles, adhesive, and grout)

Step 1: Calculate the weight of the concrete slab. Weigh of concrete slab = (175mm x 1m x 1m) x…

ing, given the following paramete Allow for 0.3kPa for M&E (i.e. Parkade mechanical and electrical like for exampl ducts, light fixtures etc..). Minimum allowance for partition walls as per ABC2019 175mm concrete slab 02kPa for tiling allowance (including tiles adhesive and grout)

ing, given the following paramete Allow for 0.3kPa for M&E (i.e. Parkade mechanical and electrical like for exampl ducts, light fixtures etc..). Minimum allowance for partition walls as per ABC2019 175mm concrete slab 02kPa for tiling allowance (including tiles adhesive and grout)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: With an observation well situated is 69.7 ft away from the pumping well (which is pumping at the…

A: Answer Based on the given data, we can use Cooper-Jabob method of solution to obtain T,K and S.…

Q: A concentrated load of P = 24 kN is applied to the upper end of a pipe with length L=7 m. The…

Q: A residential area located in an urban zone of Basrah governorate is served by the triangular pipes…

Q: A rectangular footing 2.3 mx 3.2m x 0.34 m thick supports a 300 mm square column at its center…

A: Given: Footing dimension = 2.3 m x 3.2 m x 0.34 m Square column dimension = 300 mm x 300 mm fc = 21…

Q: Sample Problem 5: Compute the forces in members CD and JK, given that P = 3000 lb and Q = 1000 lb.…

Q: A composite beam is fabricated by bolting two 2.1-in.-wide by 14-in.-deep timber planks to the sides…

Q: Given the following data: The route will use 40-seat standard buses The door opening and closing…

A: Dwell time is the time for which the vehicle stops to either drop off or pick up the passengers.…

Q: An 8 m thick saturated clay layer lies above a permeable dense sand layer. The clay settles by 40 mm…

Q: 3.3 The moist weight of 0.1 ft' of soil is 12.2 lb. If the moisture content is 12% and the specific…

Q: Based on the problem above, determine the shear stress in the grain of the timber column shown in…

Q: Hydraulic jump occurs when supercritical flow converts to subcritical flow crossing critical flow.…

Q: A grade of 0.4 percent is being considered for a mountain roadway. The elevation at the initial…

A: Elevation is the point whose height above a reference datum is noted. Given Data:…

Q: Accusoft Systems is offering small business owners a software package that keeps track of many…

Q: Q2: For the project shown below, by using (Activity on Node - AON), determine: 1. The duration of…

A: Answer Draw the Activity on Node(AON) Network based on the given table. Calculations shown in…

Q: The beam is fabricated from two equivalent structural tees and two plates. Each plate has a height…

Q: The wall thickness of a 4-ft-diameter spherical tank is 5/16 inch. Calculate the allowable internal…

Q: Explain how quartz is used to benefit humans.

A: Quartz:- A hard, crystalline mineral called quartz is made of silicon and oxygen atoms. In essence,…

Q: Using Superposition Method only, solve the following and show your complete solution: 1. Reaction at…

A: Given: Required : Reaction at A Reaction at B Deflection at midspan

Q: Exactly how does one go about tunneling? Can you name the three tunneling techniques that exist?

A: Tunneling- Civil engineering projects called tunnels establish an underground passageway that can go…

Q: Calculate the total mass of CO2 in the atmosphere. State all assumptions. Compare this to the actual…

A: The total mass of CO2 in the atmosphere is not a fixed number, as it is constantly changing due to…

Q: Three types of aggregate have sieve analysis as given below. Combine these types of aggregate to…

A: Given: Sieve size, mm Percentage passing Specification Agg. A Agg. B Agg. C 19 100 100 100…

Q: M 2 12 ft w = 30 lb/ft 12 ft

Q: PROBLEM 2: For the indeterminate beam shown below, construct the qualitative influence diagrams of…

Q: For the shape shown, a = 4 in., b = 28 in., and d = 16 in. Calculate the vertical distance from…

Q: A rigid container is closed at one end and measures 8 inches diameter by 12 inches. The container is…

A: Following are the given information, Length, L=12 in. Diameter, d=8 in. Pressure in the container,…

Q: A residential house has nine columns and requires excavation of 1m x 1m x 2m foundation. Help the…

A: Given:- The number of columns in a residential house = 9 The dimension of the foundation = 1 m×1 m×2…

Q: In a laminar flow through is a circular pipeline of 20cm diameter, the flow velocity at a radial…

A: Given- Laminar flow through circular pipeline Diameter d=20 cm radial distance=8 cm flow velocity at…

Q: A 16 mm thick plate measuring 650 mm × 420 mm is used as a base plate for an ISHB 300 column…

Q: (e) 88 (f) (g)

Q: Find the stress in each rods. The 300 mm 300 mm canatete 2m P-30 kN 2.m Steel L-0.5m E-200 GP A-500…

Q: "QC.25. Figure below shows a nonsway frame. The following are the properties of the beams and…

A: Answer Calculation of effective length factor of column AB In order to calculate the effective…

Q: Analysis of Doubly Reinforced Beams Problem 1. Compute the flexural strength of the beam shown. For…

A: The following are the given details. For concrete, fc'=20.70 MPa For steel, fy=276 MPa Section - (a)…

Q: draw shear and moment diagram; fixed support at A

A: Given: Required : Shear and moment diagram

Q: For a saturated sand deposit, the void ratio and the specific gravity of solids are 0.70 and 2.67,…

A: Given Void ratio e=0.70 Specific gravity G=2.67

Q: The principal stresses at a point a stressed material are 2 01= 200 N/mm², 02= 150 N/mm2, and 02=…

A: Given data- Principle stresses- σ1=200 N/mm2,σ2=150 N/mm2,σ3=200 N/mm2,E=210 kN/mm2Poisson's ratio…

Q: Using Castigliano s theorem for the beam and loading shown determine: 1. The vertical deflection at…

A: Given: L = 1 m F = 40 kN E = 200 GPA IPE 270 section I = 420 cm4

Q: A lake has maximum depth of 60 m. If the mean atmospheric presssure in the lake region is 91 kPa and…

A: Given- Depth h=60 m, Mean atmospheric pressure=91 kPa, Unit weight of lake water=9790 N/m3, It is…

Q: Explain in some detail why steel is not a mineral

A: Steel is an alloy which is practically man-made. Usually minerals are naturally occurring substance…

Q: Find the quarry productivity per hour for the quarry unde the following conditions: The length of…

A: To calculate the quarry productivity per hour, we can use the following formula: Productivity…

Q: A rigid bar is supported by two coppe r rods and the gap between the alumi num rod and the bar is 1…

Q: 10 m E-300 GPa 30 kN/m -10 m Ela contam -10 m 7-700 (10) m (a) Indeterminate Beam

Q: Q1-Draw shear force (S.F) and bending moment (B.M) diagrams. A is a roller and B is a hinge. 14 kN 9…

A: Given Data Draw shear force and bending moment diagram.

Q: Can you recommend any concrete strategies that may be used to track the movement of data

A: Context: Concrete strategy for movement of data.

Q: Describe the Terms Below MC-704-1 Geogrid-2 Long term aging-3

A: 1. MC-704: For waterproofing and sealcoating pavement, MC-704 is a form of flexible asphalt…

Q: Design rectangular section for the beam. Beam weight is included in the loads shown. Show sketch -f…

A: Given, Beam width (b) = 400 mm fy = 420 MPa f'c = 21 MPa

Q: cantilever timber beam with a span of L = 2.1 m supports a uniformly distributed load w. The beam…

Q: Consider a Design-and-Build project of a single-entrance toll plaza awarded to XYZConstruction Corp.…

A: The following is the given information. The present travel demand along the existing highway is…

Q: Suppose it is required to tape a length of 2500 ft with an error of not more than ±0.10 ft. If you…

Q: What is type-l settling? How analysis of type-l settling is done? Find the settling velocity of a…

Q: A common tangent of a compound curve makes an angle of 12 degrees from the tangent passing through…

Question

1. Calculate slab dead load intensity in kPa (kilo Pascal = kN/m²) in a main floor condo
building, given the following parameters:
- Allow for 0.3kPa for M&E (i.e. Parkade mechanical and electrical like for example
ducts, light fixtures etc..).
Minimum allowance for partition walls as per ABC2019
175mm concrete slab
0.2kPa for tiling allowance (including tiles, adhesive, and grout)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Pricing masonry, carpentry and finishing work

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

15. Calculate the fire resistance of a configuration of 4 wythes (monolithic slabs) of normal weight concrete each 2 inches thick. Use a conservative approach
Determine the quantity of standard concrete blocks (400 x 200 x 200) required in 100 m² of a 200 mm thick wall. Assume 5% waste. 262 pcs "1,213 pcs" O "c. 1,313 pcs" None of the above
Determine the volume of 50-mm plain concrete bedding.
Submit your question to our 24/7 subject matter experts with Masters and PhDs and get a solution in as fast as 30 minutes* Provide clear and step by step solution Using LRFD, PL400x350 mm base plate, W12x120 column, 500x500 mm pedestal, PDL = 1200 kN and PLL = 800 kN. Use A-50 steel and concrete fc’ = 30 MPa. Determine the required base plate thickness.
a. Determine the required no. of rebar and tie wire in kgs for a 3x3m dimension of RC wall with a thickness of 150mm. b. Determine how many deformed bars will you order for RC wall with a dimension of 3x3m and 175mm thickness.
Given a simple floor plan, compute for: a. Concrete materials b. Masonry materials 10.00m O.C. Column 300mmx 300mmx2.80m 4" thick CHB Fine plastered 8.00m O.C.
Prepare the details estimate for the following 2 roomed building epare BOG the foilowing WI w1 D2 3500 mm x 3400 mm 4000 mm x 3400 mm W1 D1 D1 -Door 1 1100mmx 2100mm D2 -Door 2 1000mmx 2100mm W1-Window 1 1200mmx 1200mm Roof height: 2.80m Consider bearing for lintel as RCC roof 170mm thick Lintel 0.15m thick 300mm 1 300 mm 750 mm 1000 mmm- 1200 mm ww 00s ww 00s 200 mm ww 00s
Internal effortsfeatures on a 750 mm sheet wide (made of ASTM A36 steel) were determined using a software basic structure analysis. The effort characteristic requester from a usage overhead is equal to 1260kN. Calculate the thickness needed for the plate? Adopt fyk = 250 MPa and fuk = 450 MPa.Please help Expert sir
Problem 1: Calculate Mn and check the minimum steel limit f'c =4 ksi, fy 60 ksi. 2.5" 25" 6-#9 12" 3.5" 4" 25"
You are required to design the reinforcement (both main and distribtion) for the one-way slab shown below. You then have to produce sketches (plan and section) showing your reinforcement placement. You are required also to carry out serviceability limit checks (deflection and cracking). DESIGN INFORMATION: f = 460N/mm. Diameter main bars = 10 mm. feu = 30 N/mm. Fire resistance 2 Hrs. Exposure conditions: Mild.
calculate a wall formwork pressure for a 20 foot concrete wall pour. A 20% fly ash blended cement concrete at 50 degrees will be used and the project intends to place the concrete in 3 equal lifts over 4 hours.
REINFORCED CONCRETE: kindly give the correct and whole solution and answer for this question. Thank you!!!