In the figure, suppose the length L of the uniform bar is 3.5 m and its weight is 150 N. Also, let the block's weight W = 340 N and the angle 0 = 33°. The wire can withstand a maximum tension of 370 N. (a) What is the maximum possible distance x before the wire breaks? With the block placed at this maximum x, what are the (b) horizontal and (c) vertical components of the force on the bar from the hinge at A? C com Ө A B (a) Number 1.3 Units m (b) Number 310.3 Units N (c) Number i691.5 Units N

In the figure, suppose the length L of the uniform bar is 3.5 m and its weight is 150 N. Also, let the block's weight W = 340 N and the angle 0 = 33°. The wire can withstand a maximum tension of 370 N. (a) What is the maximum possible distance x before the wire breaks? With the block placed at this maximum x, what are the (b) horizontal and (c) vertical components of the force on the bar from the hinge at A? C com Ө A B (a) Number 1.3 Units m (b) Number 310.3 Units N (c) Number i691.5 Units N

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

In the figure, suppose the length L of the uniform bar is 2.7 m and its weight is 180 N. Also, let the block's weight W = 340 N and the angle θ = 29˚. The wire can withstand a maximum tension of 400 N. (a) What is the maximum possible distance x before the wire breaks? With the block placed at this maximum x, what are the (b) horizontal and (c) verticalcomponents of the force on the bar from the hinge at A?
In the figure, suppose the length L of the uniform bar is 3.3 m and its weight is 250 N. Also, let the block's weight W = 310 N and the angle 0 = 43°. The wire can withstand a maximum tension of 43O N. (a) What is the maximum possible distance x before the wire breaks? With the block placed at this maximum x, what are the (b) horizontal and (c) vertical components of the force on the bar from the hinge at A? com (a) Number i Units (b) Number Units (c) Number Units
Chapter 12, Problem 028 GO In the figure, suppose the length L of the uniform bar is 3.1 m and its weight is 240 N. Also, let the block's weight W = 270 N and the angle e = 41°. The wire can withstand a maximum tension of 420 N. (a) What is the maximum possible distance x before the wire breaks? With the block placed at this maximum x, what are the (b) horizontal and (c) vertical components of the force on the bar from the hinge at A? Com (a) Number Units (b) Number Units (c) Number Units
Chapter 12, Problem 028 GO In the figure, suppose the length L of the uniform bar is 2.7 m and its weight is 220 N. Also, let the block's weight W = 280 N and the angle 0 = 27°. The wire can withstand a maximum tension of 440 N. (a) What is the maximum possible distance x before the wire breaks? With the block placed at this maximum x, what are the (b) horizontal and (c) vertical components of the force on the bar from the hinge at A? com A (a) Number Units (b) Number Units (c) Number Units Click if you would like to Show Work for this question: Open Show Work
In the figure, suppose the length L of the uniform bar is 3.5 m and its weight is 150 N. Also, let the block's weight W=340 N and the angle 0-33". The wire can withstand a maximum tension of 370 N. (a) What is the maximum possible distance x before the wire breaks? With the block placed at this maximum x, what are the (b) horizontal and (c) vertical components of the force on the bar from the hinge at A? (a) Number i Units (b) Number i Units (c) Number i Units com A B Ε
A bridge crossing a ravine has mass Mb and length L. The bridge is supported by pilings at points A and B at the right and left ends. A truck of mass mt stops at the point L/3 from point B. Find expressions for Fa and Fb, the forces supporting the bridge at each end.
Illustrated below is a 14-lb wooden pole tied on a 3-ft long rope at the bottom of a freshwater lake (γ = 62.47 lbs/ft3). The pole is 10 feet long and has a uniform cross-section of 7.5 in2. If the support is 8 feet below the free surface, determine the angle β produced.
a 600 N block rests of a 30 degrees plane. if the coefficient of friction is 0.20 , what is the value of the force, P applied horizontally to keep the block moving up the plane
A box with mass 178kg is supported by the cable system at B. Chord AB has a length of 1.2m and the force that develops in the chord is 3130N The horisontal distance between points A and C is 1.7m. Determine the force that develops in chord BC and the vertical height y and complete parts (a) and (b) below.
a) Cables AC and BC are connected to lifting points A & B, and joined together at C as shown in Figure Q1a. The angle = 200 and angle B = 50°. If the tension in each cable is 3.75 KN, calculate the force (F) and the angle a required to maintain point C in static equilibrium. Give your answers for F in kilonewtons (kN) and the angle a in degrees to two decimal places. A 3 F α B O
A metal block with mass 2.5kgs is clamped to an inclined board with a force of 23N. The angle between the lower end of the board and the ground is 35°. What is the minimum vertical force needed to move the block upward if the coefficient of friction is 0.2?
1 b F2 1 1 FR F1 b. The figure above shows a crane tower on site at the HWY 1 expansion and Stoney Trail extension in NW Calgary. You are a design engineer working for the company supplying cranes for the contractors and you have been asked to evaluate the tower design. The crane tower supporting the pulley is designed so that the resultant force from the cable tension running over the pulley is oriented along the tower axis. Note: The tension in the cable is the same on both sides so ||Fill = ||F2l|| = T.