In the circuit of Figure 2 with RL = 1 kilohm, determine the maximum value of Rs which will allow the source voltage Vs, vary between 1.6 Vz and 2.5 Vz without exceeding 1/4 W dissipation in Rs and still allowing Iz>3 mA. %3D Select a resistance from the standard nominal 10% resistance values listed below. The resistance should be the standard value which is appropriately higher or lower than the calculated one. 1.0 1.2 1.5 With multiples of 1, 10, 100, 1000 10,000, 100,000, 1,000,000. 2.2 4.7 2.7 5.6 3.3 6.8 1.8 3.9 8.2

In the circuit of Figure 2 with RL = 1 kilohm, determine the maximum value of Rs which will allow the source voltage Vs, vary between 1.6 Vz and 2.5 Vz without exceeding 1/4 W dissipation in Rs and still allowing Iz>3 mA. %3D Select a resistance from the standard nominal 10% resistance values listed below. The resistance should be the standard value which is appropriately higher or lower than the calculated one. 1.0 1.2 1.5 With multiples of 1, 10, 100, 1000 10,000, 100,000, 1,000,000. 2.2 4.7 2.7 5.6 3.3 6.8 1.8 3.9 8.2

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 4PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Similar questions

What is the load current for the circuit shown in the figure? Please choose one: a. 9.0 mA b. 7.5 mA c. 3.0 mA D. 6.0 mA
the non-inductive resistance of kelvin double bridge are set at 100ON each, the standard resistance is set at 0.10020 and the low resistance 0.0000122 was very low. determine the unknown resistance
aloulated m O1 the value you Up = A cos wt +1o Calaulate maarli)-min(i) =? Use constant voltage drop mad. Don7 to write units. . - 3.7V forget
In the circuit below, we have a Zener Diode circuit with a load, RL. Use the same measurements for source voltage V1 and resistor R3 resistance as in the circuit schematic. V1 -15V R3 2700 D1 1N753A RL Determine the lowest possible value for the load RL, so that the voltage drop across it is equal to the Zener voltage. For your diode, use model Zener 1N753A. This diode has a Zener voltage of 6.2V, a Zener current of 60mA, a Zener impedence of 72, and a test current of 20mA.
B.. What is the load current for the circuit shown in the figure? Please choose one: a. 6.0 mA b. 3.0 mA C. 9.0 mA D. 7.5 mA
1. The no-load terminal voltage of a battery is 30 V. The terminal voltage drops to 22 V when supplying a current of 5 A. Determine the emf and the internal resistance of this battery. Ans. r= 1.6 ohm 2. Two identical zinc carbon batteries are available. When connected in series, they supply 0.5 A to a 4 ohm resistor. When connected in parallel, they supply 0.4 A to a 5 ohm resistor. Determine the emf and internal resistance of each battery. Ans. 2.667 V and 3.333 ohm 3. When supplying a current of 5 A, the terminal voltage of a battery is 15 V. The battery is then recharged at a rate of 3 A and the terminal voltage is found to be 21 V. Determine the emf and the Internal resistance of the battery. Ans. 18.75 V and 0.75 ohm 4. A battery with an emf of 12 V and an internal resistance of 0.8 ohm is to be recharged through a 20 V source. (a) show by means of a diagram the connection of the circuit elements. (b) What is the current in the circuit? (c) The recharging current is to be…
How temperature effect conductivity? Explain with the help of following equation. m e'n7'
Refer to the circuit on the right. VEB = 0.7 V, when the BE junction is conducting. VECsat = 0.2 V B Vref = 2.2 V (Use two decimal places.) = ∞ VREF IL +5 V R LOAD Figure 2 a. What should be the value of R in ohms if IL is to be maintained at 146 mA under changing load conditions? b. In order to maintain this load current, what should be the maximum allowable load resistance in ohms?
For the circuit below, determine the resistor current. The source is 8 volts, the Zener potential is 5.2 volts and the resistor is 5k ohms.
In the figure on the right, the ideal batteries have emfs &1= 10 V and 82 = 83 = 6 V and the resistors are identical with R = 5 ohm. (a) independent eqaations to solve three unknown currents i, iz, and i; as shown in the figure and solve for the current i. That is, what is the magnitude and direction of iz? (b) (c) (d) batteries are equal to the total power loss in all the resistors. RI i ww. Apply Kirchhoffs loop and junction rules and obtain three El R3 R, 83 What is the magnitude and direction of iz? What is the total energy dissipation rate in all the resistors Prove that total power supplied to the circuit by the ww wwH
use the constant voltage drop model in analyzing the diode circuit below: 10 92 V₁ (+ M 1 V D₁ If V₁ is -3 V, what would be the state of the diodes? A. D₁ and D₂ are both OFF C B. D₁ is OFF and D₂ is ON - 1 V D₂ C. D₁ is ON and D₂ is OFF D. D₁ and D₂ are both ON + 1092 Vo
*Use 4 decimal places. **Note D1 is Germanium, D2 is Silicon, For the circuit below, determine the diode voltages VD1 and VD2, diode currents ID1 and ID2, and voltage across the resistor, VRLIMIT. Use practical model. Assume r'a=150. VBIAS = 15V and RLIMIT = 1.5kohms. VD1 = Blank 1 V; VD2 = Blank 2 V; Ip1 = Blank 3 mA; Ip2 = Blank 4 mA ; VRLIMIT = Blank 5 V Capture3(1).JPG +Vo1- +VRLIMIT +VD2- Io2 VBIAS