In order to carry out tacheometric surveying, following observations were taken through a tacheometer set up at station P at a height 1.235m. Compute the horizontal distance of S from P and reduced level of station at S if R.L. of station P is 262.575m Staff held Vertical at Horizontal distance from P Angle of Elevation Staff Reading (m) (m) 100 1.01 0° Q R 0° 5° 24' 40" 200 2.03 3.465, 2.27, 1.280 K 20 2.03m 1.01m

In order to carry out tacheometric surveying, following observations were taken through a tacheometer set up at station P at a height 1.235m. Compute the horizontal distance of S from P and reduced level of station at S if R.L. of station P is 262.575m Staff held Vertical at Horizontal distance from P Angle of Elevation Staff Reading (m) (m) 100 1.01 0° Q R 0° 5° 24' 40" 200 2.03 3.465, 2.27, 1.280 K 20 2.03m 1.01m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A Tachometer is set up at an intermediate point on a survey line PQ and the following observations were made on a vertically held staff. Staff intercept 1.235 m 1.115 m Axial hair readings 2.445 m 1.335 m Staff station Vertical angle 15° 20 ' 50" 12° 40 ' 10 " i) Compute length of the line PQ. 2.5 ii) Compute R.L of Q, if R.L of P is 189.66 m 2.5
(9) The following observations were made in a tacheometric Survey. Inst. Station A A B Hair Height staff vertical of axis station angle readings 1.345 BM 1345 B 1.550 -5° 30' 0.905, 1.455, 2.005 Remark RL of BM +8°0' 0.755,1.655, = 450-500 m +10 2.555 1.500, 2.250,3.000 Calculate the RLs of A, B and C, and horizontal distances AB and BC. The tacheometer is fitted with an anallatie Lens and the multiplying constant is 100
I need Answer of A only A. A tachometric surveying was conducted to obtain some readings forinaccessible points, where it was found that the multiplying and additiveconstants are 98 and 0.1, respectively. The instrument was setup at point C and the readings listed in the table were taken while the staff was held vertically. Calculate the horizontal distance between BM and station D. Also, calculate the reduced level of station D. Figure 1 shows a schematic view of the site.
The following tacheometric observations were 'thade on two points P and Q from station A. Staff at Vertical Angle Staff Reading Upper Middle Lower P -5°12' 1.388 0.978 0.610 +27°35' 1.604 1.286 0.997 The height of the tacheometer at A above the ground was 1.55m. The stadia constant k and c are respectively 100 and 0.0m. Determine the elevations of P and Q if the elevation of A is 75.5 m Determine the horizontal distance between P and Q if Station A is between the two stations. Show an illustration of your work. « Previous Next
The following tacheometric observations were amde on two points P and Q from station A. Staff at Vertical Angle Staff Reading Upper Middle Lower P -5°12' 1.388 0.978 0.610 +27°35' 1.604 1.286 0.997 The height of the tacheometer at A above the ground was 1.55m. Determine the elevations of P and Q if the elevation of A is 75.5 m. The stadia constant k and c are respectively 100 and 0.0m. Show an illustration of your work.
The following tacheometric observations were made from station A to stations 1 and 2. The height of the instrument above the ground was 1.52 m. Take stadia interval factor and constant as 100 and 0, respectively. If the staff was inclined by 1° to the vertical, solve for the following:a. Error in horizontal distance if the staff is inclined towards theinstrument for the line A-1. b. Error in the vertical distance if the staff is inclined away from theinstrument for the line A-2. c. If the elevation of point 1 is 115.673 m, determine the correctelevation of point 2.
Q.2 Reciprocal leveling was conducted across a wide river to determine the difference in level of points A and B, A situated on one bank of the river and B situated on the other .The following results on the staff held vertically at A and B from level station I and 2, respectively were obtain . The level station I was near to A and station 2 was near to B. Instrument at Staff reading on A 1.475 1.161 Staff reading on B 1.715 1.4 (1) If the reduce level of B is 71.18 m above the datum, what is the reduced level of A? (2) Assuming that the atmospheric conditions remain unchanged during the two sets of the observation, calculate (i) the combined curvature and refraction correction if the distance AB is 315 m, (ii) the collimation error?
Module 03- Coursework Activity 03 Complete the Differential Leveling Notes by providing data to the unknown quantities. STA FS BM1 TP1 TP2 BM2 BM3 TP3 BM4 BS 1.256 1.116 1.228 1.189 1.070 1.831 HI 1.886 1.527 2.246 2.017 2.656 2.765 ELEV 127.133
A tachometric surveying was conducted to obtain some readings forinaccessible points, where it was found that the multiplying and additiveconstants are 98 and 0.1, respectively. The instrument was setup at point C and the readings listed in the table were taken while the staff was held vertically. Calculate the horizontal distance between BM and station D. Also, calculate the reduced level of station D. Figure 1 shows a schematic view of the site.
During the dumpy level test, the observations are as follows:Staff reading stationAInstrument placedB2.2353.545AB1.6052.564Distance between A and B is 250 m and R.L of A is 435.062 m, Find the R.L of B.
51 Dr NK Assignment Dobry 2 determin 2021 To determine the distance between two points P and Q and elevation of Q, following observation were made: (2) Dr aterat ² Height of tacheometer at P = 1.280 m Vertical angle at P = + 4° 25' 20" Staff reading (with staff vertical) = 1.545, 1.905, 2.265 R.L. of P= 123.265 m. 123.265 m Dmuchantalones Calculate the unknown parameters after establishing the fundamental relations.
A line of three-wire differential levels goes from benchmark Gloria to benchmark Carey. The length of the line was determined to be 2097 m. The instrument had a stated compensator accuracy of pm 1.4 mm/ km. The instrument–rod combination had an estimated reading error of 0.4 mm per 40 m. Sight distances were kept to approximately 50 5 m. If the observed difference in elevation is 15.601 m, what is the estimated error in the final elevation difference? If benchmark Gloria had a fixed elevation of 231.071 m and Carey had a fixed elevation of 246.660 m, did the job meet acceptable closure limits at a 95% level of confidence? Justify your answer statistically.