Answered: In lathe machine, the movement of the…

In lathe machine, the movement of the tool perpendicular to the axis of the workpiece is known as________________________. taper feed cross feed longitudinal feed parallel feed

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter5: Turning

Section5.3: Machining Operations On The Lathe

Problem 15RQ: When drilling and reaming on the lathe, how are the tools usually fed into the workpiece?

See similar textbooks

Related questions

Q: Turning is a machining process in which a single-point tool removes material from the surface of a…

A: It is true that turning is a machining process in which a single-point cutting tool removes material…

Q: A mild steel specimen of Initial diameter of 53.5 mm is turned to final diameter of 47 mm for an…

Q: a drilling operation under a given condition, the tool life found to decrease from 20 mint to 5 mint…

A: Given:T1=20 minT2=5 minN1=200 rpmN2=400 rpmN3=300 rpm

Q: Why proper selection of cutting speed is important in machining? What is the main advantage of a…

A: Given Machining To find Significance of cutting speed Advantage of turret lathe Advantage of band…

Q: MI Match column A with Column B (Return this page with your answer shcet) No 1 Column A No A Column…

A: given; match with column A to column B.

Q: 1. In a turning operation, the diameter of the work- piece is 2 inches (50 mm), and it rotates at…

Q: A lathe mandrel is a hardened and tempered steel work-holding device.it is used for the further…

A: A lathe mandrel is a hardened and tempered steel work-holding device.it is used for the further…

Q: 22.1. Which of the following are examples of generating the workpart geometry in machining, as…

A: It is required to choose correct answer

Q: how would i do the Chamfering for this part on the lathe? what cutting tool would i use what…

A: Given drawing:

Q: _1. He is an English man credited for the invention of a screw cutting lathe. _2. A man from New…

A: Identification test :

Q: Choose the most appropriate answers. The unit of cutting parameter "Feed"........ Conveyors designed…

A: 1. The unit of cutting parameter "Feed mm/revolution 2. Conveyors designed within a restricted area…

Q: What are the uses of the following types of Chisel? I- Concrete Chisel: 2- Cold Chisel: 3- Cape…

A: Chisel: It is a metal tool with a sharpened edge at one end and it is used to make chip, carve and…

Q: Define the lathe machine?

A: The definition of the lathe machine is given as under.

Q: IDENTIFY THE PARTS & FUNCTIONS OF LATHE MACHINE WITH PHOTOS.

Q: In a lathe machine, the maximum torque transmitted by a shaft exceeds the mean torque by 19 %. A…

Q: Lathe operations and processes What is a single point cutting tool? What are the angles to which the…

A: 1) Lathe Operations: Step Turning: Reduction of diameter. Taper Turning: To produce tapered…

Q: The figure shows the part drawing of turning exercise in lathe machine. a) List out the operation…

A: The turning operation is performed on the lathe machine.the various operations perform in lathe…

Q: Identify the type of milling operation in which the cutter axis is perpendicular to the workpiece…

A: Milling operation in which the cutter axis is perpendicular to the workpiece being machine

Q: Why should the overhang distance of a lathe tool be minimized? What occurs if a lathe tool is set…

Q: Identify the type of milling operation in which the narrow slots or grooves can be produced into the…

A: Milling machine is a type of machine in which tool is in rotatory motion and workpiece is in leaner…

Q: The taper turning operation in lathe machine is carried out using__________ Compound rest Chuck Lead…

A: It is required to fill the blank

Q: Q1:- Choose the appropriate word. (1):- The fixed cost its ----- with number of products a- Change…

A: As per question answered all the questions above

Q: In which lathe operation, the cutting tool moves perpendicular and parallel to the axis of the…

A: Lathe is a two axis machine used to remove material from the workpiece.

Q: On a lathe, a cylindrical work piece of 100mm diameter is being turned. The RPM is 100. The lenght…

Q: 9q ___________________ is the lathe operation, which is performed without the cutting tool…

A: For thread cutting, the tool post has to move automatically based on setting of gear box. Boring is…

Q: lathe machine has a constant failure rate and a mean time to failure of 10 years. What is the…

Q: In a lathe machine, The diameter of the driver and driven pulley are 2130 mm and 1590 mm…

A: The ratio of speed of driven pulley to speed of driver pulley is termed as speed ratio for a belt…

Q: In lathe machine, the movement of the tool parallel to the axis of the job is known…

A: Basics of Lathe machine.

Q: It is an attachment that provides a quick means of chucking work-pieces with standard diameters or…

A: Combination Chuck is the correct answer.

Q: most essential parts of the lathe for it to function

A: Most essential parts of lathe.

Q: What size is called actual? 1) the size obtained in the machining of parts and measured with an…

A: Answer - option (1) - the size obtained in the machining of parts and measured with an allowable…

Q: (a) Research the cutting tool alternatives which could be used for such operation. What are the…

A: Part (b) The data given is, feed rate, f = 0.3 mm/rev depth of cut, d = 8 mm cutting speed, V = 250…

Q: Which one of the given options is wrong? a)A curvy surface is created in shaping process…

Q: Explain any three parts of a milling machine. b) Explain…

A: Milling machines Milling machines are a type of machinery for removing material from a workpiece…

Q: In a cutting operation using a – 5° rake angle, the measures forces were Fc = 1330 N and Ft = 740 N.…

Q: In what units are feed rates measured for lathe operations?

A: Feed rate is the measurement of the spindle's travel distance per rotation. The feed rate is…

Q: In lathe machine, the movement of the tool perpendicular to the axis of the workpiece is known as…

A: In lathe machine, type of feed is basically based on the movement of the tool. And this feed is…

Q: 8. Turning is a machining process in which a single-point tool removes material from the surface of…

A: The general process of turning involves rotating a part while a single-point cutting tool is moved…

Q: With neat sketch, explain the nomenclature of a reamer

A: A reamer is a tool used for expanding or finishing pre-drilled holes, or cored to give a good finish…

Q: Question 1. The shaping machine is used to machine flat metal surfaces especially where a large…

Q: A NC lathe cuts two passes across a cylindrical workpiece under automatic cycle. The operator loads…

A: Given : f = 0.007 in/rev d = 0.1 in D = 3 in To find : The cutting speed for minimum cost per piece

Q: is the lathe operation, which is performed without the cutting tool moving perpendicular to the axis…

A: A lathe is a machine tool that holds and rotates a workpiece about an axis of rotation, and then…

Q: What is a single point cutting tool? What are the angles to which the surfaces of the tool bit are…

A: INTRODUCTION : A lathe machine is a machine tool that uses a tool that traverses over the work-piece…

Q: In lathe turning operation,what is the direction of workpiece(material mounted in lathe chuck)…

A: In lathe turning operation, the direction of workpiece(material mounted in lathe chuck) rotation is…

Q: In the classification of manufacturing process, threading is an example of…

A: Solution: Secondary Machining process is a manufacturing process where a pre-machined or primary…

Q: A variety of __________ saws blades are available for rough cuts in wood, smoother cuts in wood,…

A: A Reciprocating Saw is a handheld saw commonly used for demolition and remodeling. You can use it to…

Question

100%

In lathe machine, the movement of the tool perpendicular to the axis of the workpiece is known as________________________. taper feed cross feed longitudinal feed parallel feed

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Types of Jigs and Fixtures and Their Applications

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

In lathe machine, the movement of the tool perpendicular to the axis of the workpiece is known as________________________. A- taper feed B- cross feed C- longitudinal feed D- parallel feed
In lathe machine, the movement of the tool perpendicular to the axis of the workpiece is known as longitudinal feed parallel feed cross feed taper feed
9q ___________________ is the lathe operation, which is performed without the cutting tool moving parallel to the axis of workpiece. Thread cutting Boring Operation Grooving Operation Counter Boring
In CNC lathes, to maintain constant cutting speed when feeding of the tool from the circumference to the center of the workpiece, the spindle speed (n) is needed to be: a/Increased b/Decreased c/Maintained the same
Question 19 Which of the following machine tools is the most suitable one for machining of relatively large batches with several operations? Answers: a. Toolroom lathe b. Turret lathe c. Vertical turret lathe d. Engine lathe e. Speed lathe Consider the following statements on milling machines 1. 2. Facing cutters have a tapered or straight shanks End mills usually are bolted at the end of a stub arbor 3 Plain milling cutters are used for profilling as well Answers: a. Only 2 and 3 are correct b. Only 1 and 2 are correct c. Only 1 and 3 are conect d. None of them is correct e Only 1 is correct Question 21 Find the incorrect statement about center type cylindrical grinding. (If you cannot find an incorrect statement among items a, b, c and d then code "e" for this question) Answers: & Workpiece rotates b. Grinding wheel rotates Usually workpiece traverses d, Depth of cut is usually determined by infeed of the grinding wheel e. All are correct Consider the following statements about…
Identify the part of a lathe machine which is used to give longitudinal feed motion for the tool. Cross slide Carriage Tailstock Bed
In CNC lathes, to maintain constant cutting speed when feeding of the tool from the circumference to the center of the workpiece, the spindle speed (n) is needed to be: 2 mm (079 inch) Decreased O Increased O Maintained the same
is the lathe operation, which is performed without the cutting tool moving parallel to the axis of workpiece. Grooving Operation O Boring Operation Counter Boring Thread cutting
Question 1. The shaping machine is used to machine flat metal surfaces especially where a large amount of metal has to be removed. The shaper machine is a reciprocating type of machine basically used for producing the horizontal, vertical or flat surfaces. The shaper holds the single point cutting tool in ram and workpiece is fixed in the table. A shaper mechanism is designed to give a slow cutting stroke and a quick return to a blade attached to the slider at C. Determine the velocity of the slider block C at the instant 0= 60°, if link AB is rotating at 4 rad/s. 125 mm C 45 B WAR =4 rad/s 300 mm
Name the milling machine operation in which the milling cutter axis is perpendicular to the flat surface of the workpiece surface to be machined. Face milling Form milling Angular milling Slab milling
Identify the machining operation Work Slitting Slotting Straddle Milling Face Milling
5 Clapper box is used for _______ during machining. a. Push the tool down during return stroke b. Lift the tool during return stroke c. Lift the tool during cutting stroke d. Push the tool down during cutting stroke