In Industry, three Inductive loads each of resistance R = 20 ohms and inductance L 0.04 H are connected in star to a 400 V, F = 50 Hz, 3 phase supply. I Find the following below: %3D %3D Phase voltage, Vp = Phase current, Ip= Line Current, I= The Total Power Consumed, P = The value of neutral current, IN =

In Industry, three Inductive loads each of resistance R = 20 ohms and inductance L 0.04 H are connected in star to a 400 V, F = 50 Hz, 3 phase supply. I Find the following below: %3D %3D Phase voltage, Vp = Phase current, Ip= Line Current, I= The Total Power Consumed, P = The value of neutral current, IN =

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.2P: Convert the following instantaneous currents to phasors, using cos(t) as the reference. Give your...

See similar textbooks

Similar questions

An inductive reactance of 6 ohm is connected in series with a parallel combination of a variable resistor R and a capacitive reactance of 15 ohm across 100V , 50 hz supply. a. Solve for the frequency so that the magnitude of the inductive reactance is 2 times the magnitude of capacitive reactance. b. Solve for the value of R so that the total current I will be maximum.
a. Using Ohm’s Law, compute the voltage and current for eachcomponent. Use the formula Z = Vt / It. b. Compute and record the magnitude and phase angle of the impedanceusing the equation Z= R + RL + jXL – JXC. Use 3uF for the value of C,1.006H for the value of L and for the resistance is computed based onthe specification of the lamp. c. Compute and record for the total power using the formula: Pcomputed = Scosθ d. Compute and record the reactive power and apparent power using theformula Scomputed = V2/ZQcomputed = √S2 − P2 e. Compute for the reactive power (measure) and apparent power(measured) using the formula.Q = PtanθS = P/ cos θ f. Compute the percent difference between the measure and the computedvalue of the impedance.
Answer the following: a. A capacitance is connected to a 115 V, 25 Hz mains and takes a current of 5 A. find the current when both the capacitance and frequency are doubled. b. A 220 V, 60 Hz circuit draws a current of 11 A with a power factor of 0.8 lagging. Find the resistance of the circuit.
A 5 ohm resistor in series with an inductor having an inductance of L = 15.92 mH is connected to a voltage sourceof 110 volts 60 Hz. Determine the true power consumed by the load.
Task 3 A three phase, four wire star connected load consisting of: ZR: a resistor of 9500 in series with a 3H inductor ZB: a resistor of 1950 ZY: a resistor of 1950 in series with a 4µF capacitor Using the equipment available in the power lab (Room T017), connect the given load to a three-phase supply available in the lab and: 3.1. Determine the current of each line and the neutral current and measure the total power supplied by the source. 3.2. Analytically, calculate all currents and the total power and compare with those obtained in measurements. 3.3. Device a method and measure the waveform of the neutral current. Discuss the obtained waveform and the reason for any distortion in the waveform 3.4. Validate your calculations using computer simulation
A resistance of 20 Ω, an inductance of 0.2H and a capacitance of 100μF are connected in series across 220-V 50 Hz mains. Determine the following: a) impedance b) current c) voltage across R, L, and C d) power in watts and VA e) power factor and angle of lag.
15 A of current is taken by a non-inductive load at 125 V. In order that the same current shall be generated from 240 V, 50 Hz mains. An inductor is now also then connected in series. Note: The resistance of the inductor should be ignored and also assume the waveform to be sinusoidal. Determine the phase difference between the current and the applied voltage, the impedance of the circuit and the inductance of the inductor.
Determine the complex power for the following a. P = 269 W and Q = 150 VAR (capacitive) b. Q = 2000 VAR and pf = 0.9 leading c. S= 600 VA and Q = 450 VAR (inductive) d. Vrms 220 V, P = 1kW and |Z| = 40 2 (inductive)
a) why is there a wattmeter reading when the load is purely inductiveb) why is there no wattmeter reading when the load is purely capacitive
In Industry, three Inductive loads each of resistance R - 28 ohms and inductance L = 0.07 H are connected in star to a 410 V, F = 50 Hz, 3 phase supply. Find the following below: The Total Power Consumed, P = The value of neutral current, In =
A solenoid with an inductance of 0.25 H and a resistance of 100 Q is connected to a 120-V 60-Hz source. The current is: Please check the closest answer that applies. X L 120 V 60 Hz O0.226 2-16.3° A O0.224 2-31.2° A LO
Solve for the following Requirements Load Voltages Line Currents Source Complex Power