ii, If the length of each element is 5m and the k-EA/L is given as shown, analyze the following system byDirect Method of Finite Element.ki - 200 kN/m * - 1000 kN/mky : 300 kN/m400 kN2 Develop the displacement vectorb. Develop the force vectors|c. Develop the stifness matrix for each elementd. Develop the global matrix for the syteme. Find the displacement at node 2£ Find the forces at node 1 and 3.

Answered: Image /qna-images/answer/f1f0b496-dc92-4f07-8100-a3255e4a3e2c.jpg

Answered: ii, If the length of each element is 5m…

ii, If the length of each element is 5m and the k-EA/Lis given as shown, analyze the following system by Direct Method of Finite Element. k, = 200 kN/m - 1000 kN/m ky · 300 kN/m 4 P 400 kN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine if the system is consistent or inconsistent. Justify your answer and find all solutions to the system of linear equations. Justification should be written on your solution paper. Transform the matrix into ROW ECHELON FORM (REF) using row operations. 2x +8y+ 6z = 20 4x+2y-2z =-2 3x-y+z = 11 Enter final answer: (x, y, z) =(
Fill in each of the following blanks with the appropriate word: If the displacement model used in the derivation of the element stiffess matrices is also used to derive the element mass matrices, the resulting mass matrix is called __ mass matrix.
Q3: Write a program for reading one dimensional array X(I), then arrange its element ascending (4chai) then print matrix after change.
INSTRUCTIONS: Solve the following problem by manually applying the finite element method, following these steps: Pre-processing: Geometry identification. Material properties identification. Load identification. Boundary condition identification. Development of the connectivity matrix for nodes and elements. Processing: Calculation of local stiffness matrices. Assembly of the global stiffness matrix. Assembly of the global force matrix (if required). Application of boundary conditions. Resolution of the system of equations. Derivation of the complete displacement vector (u). Post-processing: Reaction forces calculation. Stress analysis. Problem Statement: the truss nodes and elements (in parentheses) are already numbered. The areas (are in cm^2 ) are underlined. members are made of structural steel, modulus of elasticity is (E) of 20×10^6 N/cm^2 . the lengths are given in cm.
Q2) for the following RRRP manipulator: • Fill out the parameters table based on the modified D-H representation. • Write all the T matrices. L2
Points for stress vs strain (in image) Assume the compressive concrete strength (f’c) is 3,000 lb/in2 (psi)Calculate a cubic function (3rd order polynomial – Ax3+Bx2+Cx+Constant)Use this function to create a function that describes the slope of the cubic function (the derivative of thecubic function). This new function allows you to calculate the tangent to any point along the curve. Thetangent is the modulus of elasticity (E). The concrete code provides a formula to calculate E for concrete. That formula is:E = 57,000√??′, where f’c is in units of psi, and E is in units of psi.Use the derivative function you calculated to locate the point on the curve where the slope of the curvematches E using the concrete code formula. Express that stress point on the curve as a percentage ofthe compressive strength of the concrete. Now, calculate the secant modulus for the test case using 1,500 psi (50% f’c) as the arbitrary point onthe curve.Assume fracture occurs at the last point…
Please Draw The Freebody On a sheet of paper Only and Solve via Handwritten Only. Here I am facing difficulty in Typed based solution. [Reaction(N) and angle(°)]
(b) A beam is subjected to a linearly increasing distributed load. The elastic curve (deflection) is shown in the figure. The equation to find the maximum deflection is given below. Create a matlab code where you can calculate the maximum deflection (dy/dx=0) using the bisection method. Use initial guesses of 1 and 4, L= 6.46 m, E = 59000 kN/cm2, I=35000 cm4, and w0= 2.5 kN/cm. What will be the value of x (location of maximum deflection) after 14 bisection iteration? wo -23 +2L?x³ – L^x) 120EIL dy wo (-5x4 + 6L²a² – Lª) da 120EIL Choices 1.4445 O 2.6001 O4.3335 O 2.889
アN 0. 2. B=2 Matrix ) Find all the eigen values. ) Calculate the eigenvector correspon ding to the Caleulare largest eigenvalue.
3. Jacobian Matrix: a) Derive the equation for Joint Force of the given planar 1R robot. As it's a planar robot, forces at the end-effector are Ex and Ex. b) Find the force (FX) when the link length is 0.5 m, Joint force is 1 Nm, Joint variable, 0 = 60 and Fx = 0 N. T P₂ y r F -F₂ ee 0,0 F Р. X 7 ४
A A squere plate is boended by the liner x = ±2, y= ± 2. The boundlary femperatures %3D are on the hine y=2, T=-8o on the line x-12,T=-40Y on the line y=-2, T= 240 + 8ox for -25x Ko 7 = 240 - 8o x tor o
2. Solve the system linear of Equation using Gauss- Jordan elimination (row operations), find the value of x1, x2 and x3. 2X1 - 2X2 + X3 = 3 3X1 - X3 + X2 = 7 X1 - 3X2 + 2X3 = 0