Answered: If the soil sample has a water content…

If the soil sample has a water content of 11% and a unit weight of 19.67 kN/m3, determine the percentage of air in voids and the degree of saturation if the specific gravity of soil solid is 2.75

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter4: Plasticity And Structure Of Soil

Section: Chapter Questions

Problem 4.4P: Results from a liquid limit test conducted on a soil are given below. a. Determine the liquid limit...

See similar textbooks

Related questions

Q: Two pipes A and B are connected in parallel between two points M and N as shown in figure. Pipe A is…

Q: A 15cm diameter pipe is joined to a 30 cm diameter pipe by a reducing flange. For water flowing at a…

Q: Calculate the maximum moment for the given moving loads shown Given: P=48.92kN X=3.52m

Q: Q.1 In a falling head permeability test drop in head OCcurs from 60 m to 40 m in 10 minutes. The…

A: given- falling head permeability test, time t=10 minutes, heads- h1=60 m,h2=40 m,areas-a=2 cm2,A=20…

Q: What is the vertical deflection at C. The cross-sectional area and moment of inertia of each segment…

Q: Compute the critical and normal depths in a trapezoidal channel (bottom width = 20 ft, side slopes =…

A: Given data : Bottom width = 20 ft Side Slope - 1.5 : 1 Flow Q = 220 ft3/sec Bottom slope = 0.0032 n…

Q: Provide at least 5 pictures of unsafe/unhealthy acts/conditions. Then, Determine the Hazard in each…

A: To answer - 5 hazard condition at working site of civil construction and their solution. Note -…

Q: Due to ageing of a pipeline, its carrying capacity has decreased by 25%. The corresponding increase…

Q: 2- Determine the slope and displacement at C. E= 200 GPa and I = 5 (10) mm¹ is constant. Use the…

A: Given : E = 200 GPa I = 5 X 106 mm4 To Find : Slope and displacement at C

Q: What are the four different methods used to evaluate the potential for liquefaction of soil

A: There are four different methods used to evaluate the potential for liquefaction of soil.

Q: 5. x = A sin (wt + ß); w a parameter, not to be eliminated.

A: Objective: To eliminate the arbitrary constants (A, B). Given: x=Asin(ωt+B)

Q: A golf ball is struck with a velocity of 80 ft/s as shown. Determine the speed at which it strikes…

Q: Problem 2 In a compass survey made 50 years ago the observed magnetic bearing of a reference line XY…

Q: m s² Situation 1: A body has a weight of 400 N at standard earth's gravity of 9.81 When a force of…

Q: Calculate the deflection ABv,. E = 10,000 ksi C 10' 4 in² A 6 in² 4 in² 10' 30 K D 6 in² 6 in² 10' B

Q: A bench Mark has been established at the soffit of an ornamental arch at the known elevation of…

Q: If the soil sample has a specific gravity of 2.71 and a porosity of 0.345, determine the saturated…

Q: If Superman has a mass of 220 lbm on his birth planet Kryptor where the acceleration of gravity is…

A: Mass(m)=220lb Acceleration (a)=82ft/s2 to find weight

Q: 9 ft A ₁2 k 12 ft F B 12 ft- E 12 ft -30°

Q: body has a weight of 400 N at standard earth's gravity of 9.81

A: Given: Weight of the body, W = 400N at g = 9.81 m/s2 To determine the acceleration of the body when…

Q: Deflection of Beams Calculate bending moments and shear forces for the following cantilevers and…

Q: A RC column is having 1% steel of cross sectional area of column. Assurme a modulus ratio of 10. The…

A: Given data- RC column is having 1% steel of cross-sectional area of the column. modulus ratio m =…

Q: Draw the influence lines for (a) the vertical reaction at A, (b) the shear at C, and (c) the moment…

A: Lo = 5 +4 + 7+3 = 19

Q: What are the three methods to mitigate liquefaction hazards? Explain each briefly. 1. Mitigation of…

A: There are different tyoes of methods which are used for minimising the hazard developed due to…

Q: 45. An organization responsible for developing the RS (recommended standard) series of stand for…

A: Electronic Industries Association is an organisation responsible for developing recommended standard…

Q: A piece of material is subjected to tensile stress of 70 N/mm² in one direction and a pressive…

Q: A steel tape is 100 m long at a standard pull of 65 N. Compute the pull correction in mm if during…

Q: A mixed liquor sample form an activated sludge plant was settled in a one-litre measuring cylinder…

Q: 2 QUESTION 2 A propped cantilever beam is shown in Figure 2. Use Macaulay's method to calculate the…

Q: Draw the Orthographic Projections (Top View, Front View, Side View) For the Shapes Shown Below,…

A: Answer We can draw the orthographic projections using the following steps in Autocad 1) Set the…

Q: The train passes point B with a speed of 10 m/s which is decreasing at at = -0.2 m/s². Determine the…

Q: Which tools that can be used to :1 draw the following shape in .AutoCAD Left-side view Top view…

A: Answer: 4. Construction Lines, Offset, Line, Trim, Layers

Q: Draw the following square shape in AutoCAD Using injunctions Mirror, Offset, then find the distance…

Q: For the system shown in Fig.(3), what is the least value of the force P to cause block B move to the…

Q: 0.5 m2 an

A: Single- cutting pump Area (A) =0.5m2 Length of stroke (L)= 10cm = 0.1 m Speed of pump(N) =…

Q: Given the truss and loading shown below, determine the stress at member Al if Pu = 18.375 Kips and…

Q: ..An unsymmetrical parabolic curve has a back tangent of 7% and a forward tangent of -4%…

Q: A 300 mm square bearing plate settles by 15 mm in a plate load test on a cohesive soil when the…

A: Given data- width of plate Bp=300 mm,settlement of plate Sp=15 mm,width of footing Bf=1m=1000 mm, To…

Q: Given the truss and loading shown below, determine the stress at member AB if Pu = 18.375 Kips and…

Q: A machine shop wishes to set aside money now to invest over the next 4

A: Given: A shop invests money for the next four years on it computer system as follows Year 1: $25,000…

Q: A 5-m wide rectangular channel is carrying a flow of 5 m3/s. If the Manning n = 0.013 and the bottom…

Q: If the irrigation efficiency is 80%, conveyance losses are 20% and the actual depth of watering is…

Q: For the truss shown below, use joint method to determine the forces in all the members of the truss…

Q: The community of Enviro, USA, has found that its present ground water supply is inadequate to meet…

A: Po = 40,000 r = 2% = 0.02 Pn = Po (1 +r)n P10 (@1/1/2032) = 40,000 (1+0.02)10 = 48,760

Q: The hydraulic conductivity of a clayey soil is 3 × 10-7 cm/sec. The viscosity of water at 25 °C is…

Q: The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces…

Q: You have just moved to a new country to take up a two-year assignment. You need to buy a car and are…

A: If a new car costs $20.000 and a car that is three years old costs $9,000, The used car has…

Q: A gravity dam of trapezoidal cross-section with one face vertical and horizontal base is 22 m high…

A: First we will calculate the value of base of dam. This will be done with the equation containing…

Q: Problem 6.41 Consider the truss shown in (Figure 1). Suppose that F = 25 KN Part A Determine the…

A: Given ; F = 25 kN To Find :: 1) FFE 2) FEB 3) FBC

Q: Solve for the force in the marked members in each truss. 4@4 m = 16 m 12 kN 2m 3 m

A: "Since you have posted multiple question , we will be solved first for you , to get the remaining…

Concept explainers

Soil engineering for highway design

Soil engineering is a part of geotechnical engineering that deals with the characteristics of soil. It also helps to understand the behavior of the soil in different conditions. The basic concepts of soil are studied to check the strength, compressibility, and porosity of the soil. This makes soil engineering an important topic for civil engineering.

Question

100%

If the soil sample has a water content of 11% and a unit weight of 19.67 kN/m3, determine the
percentage of air in voids and the degree of saturation if the specific gravity of soil solid is 2.75.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A sample of soil in its natural state has a volume of 1.396 m3 and weighs 18.662 kN. The sample was taken to the laboratory to determine the mass of solids. After oven-drying, the soil weighs 15.036 kN. If the specific gravity of the soil solids is 2.667, determine the following: Porosity, Degree of saturation, Effective unit weight. show complete solution
If the soil sample has a water content of 11% and a unit weight of 19.67 kN/m³. Determine the percentage of air in voids and the degree of saturation if the specific gravity of soil solid is 2.75.
A soil sample is taken from a small test hole at a construction site. The volume of the test hole is determined to be 0.025 m³. The wet mass of the soil is 53.4 kg and the dry mass is 47.7 kg. The specific gravity of the soil solids is 2.70. Determine the wet and dry density, , water content, void ratio, and degree of saturation
A soil sample has a weight of 120 grams before it was placed on the oven. After drying for 20 minutes, it weighs only 100 grams. Specific gravity of soil sample is 2.6. Volume of soil specimen before drying is 66 cm³. a. Compute the water content b. Compute the void ratio c. Compute the degree of saturation
Example 1 For a soil specimen; given that The moist mass of soil specimen is 20.7 kg Specimen's volume measured before drying is 0.011m³ Specimens dried mass is 16.3kg Specific gravity of solids is 2.68 Determine the following a) Void ratio b) Degree of Saturation c) Wet unit mass, dry unit mass d) Wet unit weight e) Dry unit weight
Q1-) A soil sample in plastic limit state weighs 2.535 N and becomes 1.980 N after oven drying. The plasticity index and the shrinkage limit of the soil are 11% and 15% respectively. Determine the quantity of water in liter to be added or taken out of the sample to change its state to: i- Solid state. ii- State at which the liquidity index equals to two.
A soil sample has a bulk unit weight of 19.6 kN/cu.m at water content of 10%. Assuming G=2.7, determine the percentage air in the voids (air voids).
The moist (total) weight of 0.1 ft3 of a soil sample is 12.2 lb. If the water content is 12% and the specific gravity of the solid is 2.72, calculate: The weight of the solid (Ws) and the volume of the solid (Vs). The degree of saturation Void ratio
The volume if the soil sample measured before drying is 11 cu.cm. The wet weight of soil is 207 g and the dried wet of the soil sample is 163 g. If the sp.gr. of soil is 2.69, determine the following:a) Void ratiob) Degree of saturationc) Dry unit weight a zero air voids
A soil specimen has a water content of 10%, and a unit weight of 20KN/m³. If the specific gravity of solids is 2.7, determine the dry unit weight, void ratio, and the degree of saturation. Take unit weight of water Y= 10KN/m³.
A man collected a sample of soil outside of his house. The moist unit weight of the soil is 18.9 , and the soil solids have a specific gravity of 2.67. If the soil is found to have a water content of 9.8 %, determine: a.) Void ratio b.) Dry unit weight c.) Degree of Saturation d.) How much water to add () to achieve a degree of saturation of 89 % e.) How much water to add () to achieve full saturation
SUBJECT: SOIL MECHANICS A soil sample has a bulk unit weight of 19.6 kN/cubic meter at a water content of 10% Assuming that the specific gravity of the solids is 2.1 a. Determine the percent (%) of air in the voids.