If the ratio between the length of the tape to its width is 45, the number of tapes used to irrigate a field 300 tapes, the irrigation time per tape is 55 minutes, and the available irrigation current is 30 L / sec, calculate the length of the tape and the design flow rate in units of M '/ hr if you know that the irrigation efficiency is% 70, the effective root zone depth is 1.5 m, the moisture depletion rate is 60%, and the water holding capacity is 1.3 mm / cm.

If the ratio between the length of the tape to its width is 45, the number of tapes used to irrigate a field 300 tapes, the irrigation time per tape is 55 minutes, and the available irrigation current is 30 L / sec, calculate the length of the tape and the design flow rate in units of M '/ hr if you know that the irrigation efficiency is% 70, the effective root zone depth is 1.5 m, the moisture depletion rate is 60%, and the water holding capacity is 1.3 mm / cm.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

6. After your flash mix the water was sent to a clarification basin that was 24 feet in diameter and 20 feet tall. What was the detention time in hours of 0.43 MGD? 5.4 hours 4.3 hours 3.8 hours 2.3 hours After the water leaves your sedimentation basin, it is ready for filtration. Your two filters measure 10 feet in diameter. What is the filtration rate is gpm for your flow of 0.43 MGD? 19 gpm/sq/ft 29 gpm/sq/ft 39 gpm/sq/ft 49 gpm/sq/ft You have had a filtration breakthrough (failure) and have brought your old roughing filtration system on line. The old filter is 8 feet square and 4 feet deep. What is the filtration rate in gpm/sq/ft for your flow of 0.43 MGD? 10.33 gpm/sq/ft 8.55 gpm/sq/ft 5.99 gpm/sq/ft 4.66 gpm/sq/ft
T Settled sludge and filter wash water from water treatment are thickened in Problems 703 clarifier-thickeners prior to mechanical dewatering. The settled sludge volume is 1150 gpd with 1.0% solids, and the backwash is 9800 gpd containing 500 mg/l of suspended solids. Calculate the daily quantity of thickened sludge, assuming a concentration of 3.0% solids
A 25 ml of sewage water sample was refluxed with 10 ml 0f 0.25 N K2Cr2O7 solution. The untreated dichromate requires 6.5 ml of 0.1 N FAS.10 ml of dichromate solution and 25 ml distilled water , under the same condition as sample required 27 ml of 0.1N FAS. Calculate the COD of sewage.
a) Mention the main characteristics of evaporation.b) Difference between particle specific surface and bed specific surface
Sketch a preliminary process flow diagram for a split-treatment lime-soda ash water treatment plant to soften a design flow of 60 mgd. Use six equal-sized flocculator-clarifiers . The first-stage flow for excess-lime treatment is expected to be 110 greater than 50% of the raw water. Use eight gravity dual-media coal-sand filters with traditional flow control using rate-of-flow controllers . The preferred backwashing system is air scouring prior to water backwash. The clear-well capacity is 6.0 mil gal. The raw water has a hardness of approximately 230 mg/l, iron in the range of 0.2-0.3 mg/l, and a less than optimum concentration of fluoride. On the flow diagram, show the chemicals being added and their points of application. Sketch a cross-sectional view of the filter box showing the wash-water troughs, filler media, and underdrain system. List the design criteria for sizing the flocculator-clarifiers and filters.
1- - 1/ Question 1 (i) Sketch, label and explain all the different parts in activated sludge system used during secondary treatment of wastewater. Give one (1) important reason why secondary sedimentation tank is normally installed after an activated
3. Circular clarifiers are used to remove solid materials from water. They allow continuous treatment of water and can handle fairly large flows. Solids settle to the bottom of the clarifier and are carried away by a small stream of water (the waste stream). Most of the water exits the tank as treated effluent. Assume a clarifier receives a flow of 0.10 m3/s with a solid concentration of 800 mg/L. If the waste stream consists of 3% of the incoming flow and carries 90% of the incoming solids, a) what is the solids concentration in the waste stream, and b) what is the solids concentration in the treated effluent?
Problem 1 A mechanically cleaned bar screen is used in preliminary treatment for the following conditions: Wastewater flow rate = 100,000 m/d Approach velocity 0.6 m/s Open area for flow through the screen = Head loss coefficient for clean screen Head loss coefficient for clogged screen = 0.60 Incline from vertical = 0° %3D 1.6 m2 0.75 I %3D a. Calculate the clean water head loss through the bar screen. b. Calculate the head loss after 40% of the flow area is clogged with solids.
Design grit chamber to treat peak design flow of 150 MLD (3 x Average waste water flow of 50 MLD) of wastewater to remove grit particle upto a size of 0.15mm and of specific gravity of 2.65. The minimum temperature is 15° C. The grit chamber is equipped with proportional flow weir as control device. Take kinematic viscosity at 15°C as 1.14 x 10-6 m²/s.
A sand bed filter is 50 ft in diameter and filled to a depth of 20 ft with sand. The sand particle diameter is 1 mm and the initial bed void fraction is .34. Wastewater containing 1% by volume suspended solids is fed to the filter at a rate of 4500 gpm by a positive displacement pump which can delvier this rate up to a discharge pressure of 45 psig. Determine how long in hours the filtration system can operate before shutting down for backwashing.
2. A scrubber separator is used to remove sulfur dioxide (SO2) from a gas stream. A 0.5 m'/sec inlet stream (350 K, 1 atm) contains 1.2 ppmv SO2. Find the required removal efficiency if the cleaned outlet stream must contain no more than 240 µug/scm.
A venturi scrubber operates such that Nt =(PT)1/2. At a power input of 4 hp/1000 cfm and an Inlet dust loading of 1.5 gr/ft2 what is the outlet loading?