If given that the polar moment of inertia for any shape is given by the equation J = lu + ly, where I is the moment of inertia of the section, draw the maximum torsion stress distribution of the following cross sections indicating all values of importance. All cross sections are symmetrical around the x and y axis. The torsion moment on all sections are 20kN.m clockwise. S0mm 200mm 50mm 500mm 50mm 50mm All circles has a radius of 25mm.

If given that the polar moment of inertia for any shape is given by the equation J = lu + ly, where I is the moment of inertia of the section, draw the maximum torsion stress distribution of the following cross sections indicating all values of importance. All cross sections are symmetrical around the x and y axis. The torsion moment on all sections are 20kN.m clockwise. S0mm 200mm 50mm 500mm 50mm 50mm All circles has a radius of 25mm.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The two bars are made of polystyrene, which has the stress-strain diagram shown. If the cross-sectional area of bar AB is 975 mm² and BC is 2600 mm², determine the largest force P that can be supported before any member ruptures. Assume that buckling does not occur. Include complete steps with explanations and FBD. 1m baxilno σ (MPa) 175 140 105 70 A 35ptension 0 0.20 -1.2 m P 0.40 compression B 0.60 0.80 € (mm/mm)
A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
The beam is loaded by two point forces P. The beam is assembled according to the cross-sectional view by nailing wooden parts with cross-sections of 50 mm x c = 220 mm and 25 mm x d = 260 mm. How large can the value of the load P be when the distance between the nails in the longitudinal direction of the beam is 100 mm, the cross-sectional area of the nail is 9 mm2 and their permissible shear stress is 110MPa? Then calculate the maximum stresses and shear stresses of the beam at that load when the distance between the articulated supports is L = 1.9 m and the length of the beam projections a = 1.3 m. Permissible shear force of one nail? kN Static torque of the cutting surface? mm^3 Maximum torque change in cantilever? kNm Cutting force of the projection? kN Magnitude of force P? kN Calculated with the obtained force P maximum normal stress? MPa shear stress maximum? MPa
Compute the deformation of the beam using area method:E= 200 GPa I= 1000 x 106 mm4
! Required information Consider the given state of stress. to A16 ksi 10 ksi Determine the normal and shearing stresses after the element shown has been rotated through 10° counterclockwise, using Mohr's circle. The normal stress ox'is ksi and oy'is |ksi. The shear stress Tx'y'is ksi.
To lower ends of the three bars in the figure two are the same level before the rigid homogeneous W=176kN block is attached. Each still bar has a length of 1.00 m, an area 500mm² and E=200 GPa. For the bronze bar the length is 1.6m, the area is 900mm² and E= 83 GPa. What is the stress developed in the bronze bar? What is the stress developed into steel bar? What is the elongation of each bar?
! Required information Consider the given state of stress. A 16 ksi 10 ksi Determine the normal and shearing stresses after the element shown has been rotated through 15° clockwise, using Mohr's circle. The normal stress Ox'is - |ksi and Oy'is ksi. The shearing stress Tx'y'is ksi.
the largest axial P force that the given riveted joint can safely carry.calculate. Rivet diameter 32mm and plate width 310mm. Shear stress of the rivet1400 kg/cm2, crush safety stress of rivet 2800 kg/cm2and the platetensile safety tension 1400 kg/cm2will be taken. t1=20mm t2=37mm
2-29. The rectangular plate is deformed into the shape shown by the dashed lines. Determine the average normal strain along diagonal AC, and the average shear strain at corner A relative to the x, y axes. Problem 2-29 2 mm 300 mm D mm 400 mm 400 mm 6 mm CI 6 mm 2 mm T -3 mm X
TRUE OR FALSE ONLY. PLEASE HELP 1. Area of shear diagram is equal to the magnitude of bending moment. A 2. Parallel area is the resisting area for shear force. 3. The deflection of the beam is its elastic curve when the beam bends 4. Flexural stress is a bending stress. 5. The elastic limit is the limit beyond which the material will no longer go back to its original shape when the load is removed, or it is the maximum stress that may be developed such that there is no permanent or residual deformation when the load is entirely removed.
The two-dimensional framework consists of two bars CE and CD pinned at C, D and E; and a horizontal bar AB pinned at A as shown in the figure. Because of an assembly error the bar AB is slightly short of length ?. Determine the required axial force necessary to close the gap ?. All bars are made of steel and of the same cross-section and modulus of elasticity ? = 200 ??a
Calculate the stresses that will occur at point A in the adjacent figure. r=10mm