Give a short answer to each of the following:1- A radio set consists of three major components: a powersupply(A), cleaver (B), and an amplifier (C), havingRAreliabilities R(A) 0.9, R(B) 0.8, and R(C) 0.85,Rerespectively. Compute system reliability if?Rg1-If the cleaver component fails , find new Rs.II)-If the amplifier component fails , find new Rs.2- Define the industrial organization? And list types of organisation? Support your answer withfigure of one type only..3- Describe the concept of JIT strategy Japanese ? listed a five benefits of it?4 Based on your knowledge in planning, define project and phases of large complex projects?5- What is meaning of MRP , BOM, Product structure tree,From the figure, Determine the quantities of (D, E,only)B(2)C(2)needed to assemble 2 x.D(3)E(2)F(2)티4)

Given, R(A)=0.9 R(B)=0.8 R(C)=0.85

I- A radio set consists of three major components: a power supply(A), cleaver (B), and an amplifier (C), having RA reliabilities R(A) 0.9. R(B) 0.8, and R(C) 0.85. Re respectively. Compute system reliability if? Ra D-lf the cleaver component fails, find new Rs. II-If the amplifier component fails, find new Rs.

I- A radio set consists of three major components: a power supply(A), cleaver (B), and an amplifier (C), having RA reliabilities R(A) 0.9. R(B) 0.8, and R(C) 0.85. Re respectively. Compute system reliability if? Ra D-lf the cleaver component fails, find new Rs. II-If the amplifier component fails, find new Rs.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

With the aid of diagrams, show and explain how phase locking is used to demodulate a frequency-modulated (FM) signal.
The hardware systems operate under a static discipline with the following voltage thresholds:VIL=2.5V,VIH= 3.9V,VOL= 1.5V, and VOH= 4.7V. Computethenoisemargin.And draw the properly labelled noise margin figure for thissystem.
For question 1, The instructor asked what is an approach to modulate a PWM signal and what is an approach to demodulate a signal. Thank you. Explain one approach for PWM modulation and detection (demodulation). Please draw the required circuits and diagrams.
4) The extent to which series mode noise corrupts measurement signals is measured by a quantity known as--- 4) noise ratio , B)Dual signal-to-noise ratio , C) A&B , D) signal-to-noise ratio . 5) Sometimes used to provide shielding from capacitive-coupled noise, but the necessary supports for the conduit provide multiple earth points and lead to the problem of------? A) Shielding, B) Multiple earth, C) Earth loops, D) Noise.
In a EM system, the modulating frequency fm = IKH3, the modulating Voltage Vm = 2 and the deviation is 6KHZ If the modulating voltage is raised to 4 volt then what will be the new deviation ? If the modulating voltage incroasod to 8 volt and madulating frequer IS reduced to so0 Hz, what will be deviation 2 6.
C ompare the amplitude modullation and frequency modulations. What arethe advantages and disadvantages of both systems? (Please original answer not copy from internet)
b) Draw the block diagram of the phase - locked loop (PLL) that can be used to demodulate FM signals. Explain briefly . the operation of this demodulator
answer all A - Explain the relation of MOSFET input current and input impedance and their effect on the functionality of the device. B- Explain how to increase the efficiency of the solar cells (PV cells) through the integration of antennas. C- List three conditions need to be considered to choose a MOSFET for switching applications.
Q: Explain why the envelop detector cannot demodulate the over-modulated signal . Discuss how to demodulate the over-modulated signal.
B- Write the procedures of pickup the EMG signal to predicate the angle at the Ankle joint.
This problem is AC analysis problem. DC analysis is not needed to answer the question. A) If we assume that the peak voltage of Vbe must be less than 10 mV to avoid small signal violations determine the value of Rsig if Vi has a peak amplitude of 1 V and Is = 1mA. Hint: Don't forget r!! Answer: Rsig =. B) If you did the DC analysis on this problem and calculated Vc = 50 mV and Vs = -100 mV what is the maximum amplitude of the output voltage while the circuit stays in active mode. Answer: Vo,max =, When you "verify" a mode of operation you will need to calculate all three voltages (Vc, Ve, VE for BJTS and VG, Vs, Vp for MOSFETS) and show the correct two conditions are satisfied. Assume Capacitors acts like open circuits at DC and short circuits for AC. > Assume the following: 5V o Beta = 100 O VBE = 0.7 o V: (Thermal) = 26 mV o Vr (Threshold) = 2V O VA = - o For MOSFET saturation mode: assume: lp = K(VGs-Vr)? (Assume K = 10 mA/V²). 5kn C2 01 C1 Rsig 1kn 10k Vi IIs :C3 1mA -5V
For a ZVS resonant switch converter, Vs = 20 V, 1, = 2 A, L, = 10uH, C, = 0.1uF, and f; = 100 kHz. Determine: i. the output voltage, ii. the maximum L, current, iii. the maximum C, voltage, iv. the switching frequency such that the output voltage is 14 V, v. the maximum resistance of the load still permitting zero-voltage turning on of the transistor.