I 1. Determine the apparent specific gravity (G.), dry bulk specific gravity (Gs(OD)), SSDbulk specific gravity (Gt(ssD) and absorption capacity of a fine aggregate sample using thefollowing data:Weight of sample in dry condition: 485 g• Weight of sample in SSD condition: 505 g• Weight of pycnometer with the sample and water: 1015 gWeight of pycnometer with water: 700 g

Given: The dry weight of the sample is 485 g. The SSD weight of the sample is 505 g. The pycnometer…

Answered: I 1. Determine the apparent specific…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

5) Determine the apparent specifie gravity (G.), dry bulk specific gravity (Guon), SSD bulk specific gravity (Ghessn) and absorption capacity of a fine aggregate sample using the folowing data: • Weight of sample in dry condition: 485 g Weight of sample in SSD condition: 505 g • Weight of pyenometer with the sample and water: 1015 g • Weight of pycnometer with water: 700 g
Example 2: Specific gravity test was conducted for a fine aggregate. If the following data was obtained during the test: - the saturated surface dry weight of the sample = 500 g. %3D - Weight of pycnometer full of water= 750 g - Weight of pycnometer and sample and water= 1050 g. - Oven dry weight of the sample is 475 g. for this aggregate, FIND - The apparent specific gravity. - The bulk specific gravity on an ssd basis. Percentage of absorption.
A saturated aggregate sample with an absolute volume of 5.05x10^-5 m^3 has a mass of 178 g before drying and 139 g after drying in an oven. Assume the water absorption by volume to be 59.18%. Determine the following: a. Specific gravity of the solid particles b. Mass specific gravity c. Void Ratio d. Porosity
A sieve analysis test for fine aggregates was performed on a sample of fine aggregates and produced the following results below. Determine the following: a. Percent passing through each sieve (Tabulation) b. Plot of the percent finer in the Semi-Log Gradation Chart c. Maximum Aggregate Size of the Sample (mm) d. Nominal Maximum Aggregate size of the sample e. Fineness Modulus
Sieve analysis of a sample of fine aggregate resulted in the following data No. Sieve number 4 8 16 30 50 100 Sieve opening (mm) 4.75 2.36 1.18 0.6 0.3 0.15 Weight retained (g) 13 75 120 126 105 61 A) The total weight of the sample, assuming no mass loss during the analysis, is______ (g) a) 505; b) 500; c) 550 B) The half sieve used in the experiment is________. a) No.8; b) No.50; c) none of the above C) The fineness modulus of the aggregate________. a) 6.13; b) 3.16; c) 1.36 D) The average size of the aggregate___________. a) No.30; b) No.4; c) No.16
SURFACE MOISTURE OF FINE AND COARSE AGGREGATE Pycnometer or Flash Method make up computation, make one Mass of specimen (S) Mass of pycnometer + water (C) Mass of pycnometer + water + specimen (W) Mass of displaced water (V) Specific Gravity, G 2.86 D = S/G % surface moisture
Sieve analysis test for fine aggregates was performed on a sample of fine aggregates and produced the following results: a. Calculate the percent passing through each sieve. b. Plot the percent finer in a semi-log gradation chart. c. What is the maximum aggregate size of the sample? d. What is the nominal maximum aggregate size of the sample? e. What is the fineness modulus? Is it in typical range? 0.18 0.15 (No. (3/8) INo. 41 (INo. 6) (No. 8)|(No. 10) (No. 16) (No. 20)|INo. 30)|(No. 40)|(No. So) (No. 60)|(No. 80) 100) Sieve Size, 9.5 4.75 3.35 2.36 2.00 1.18 0.85 0.60 0.425 0.30 0.25 0.075 Pan mm (in) (No. 200) Amount 25 59 75 86 115 136 169 192 225 198 173 112 90 33 12 Retained,
A sieve analysis test was conducted for sample of fine aggregate and obtained the results as shown in Table Q1. Calculate the percent passing of each sieve and classify the fineness of fine aggregate based on fineness modulus analysis. (c)
A sample of wet aggregate 297.2 N. After drying in an oven, this sample weighed 281.5. The absorption of this aggregates is 2.5%. Calculate the percent of free water in the original wet sample. Weight of the wet aggregates (Wwet) = 297.2 N Weight of the dry aggregates (Wdry) = 281.5 N
TEST PROCEDURE: 1. Dry the aggregate test sample to a constant weight at a temperature of 110 ± 5°C, then cool to room temperature. 2. Select suitable sieve sizes to furnish the information required by the specifications covering the material to be tested. Common sieves in millimeters are 37.5, 25, 19, 12.5, 9.5, 4.75, 2.36, 1.18, 0.6, 0.3, 0.15, and 0.075 mm (11 2 in., 1 in., 3 4 in., 1 2 in., 3 8 in., No. 4, No. 8, No. 16, No. 30, No. 50, No. 100, and No. 200). 3. Nest the sieves in order of decreasing size of opening, and place the aggregate sample on the top sieve. 4. Agitate the sieves by hand or by mechanical apparatus for a sufficient period. The criterion for sieving time is that, after completion, not more than 1% of the residue on any individual sieve will pass that sieve during 1 minute of continuous hand sieving. 5. Determine the weight of each size increment. 6. The total weight of the material after sieving should be compared with the original weight of the sample placed…
1. Calculate the following properties for the data provided in the Table below for a coarse aggregate sample. a. Bulk SSD specific gravity b. Bulk Dry specific gravity A Bulk Dry Sp. Gr. = c. Apparent specific gravity d. Absorption capacity. В — С B Bulk SSD Sp. Gr. = В — С where A Apparent Sp. Gr. = А — С A = dry weight B = SSD weight C = submerged weight В — А (100) A Absorption (%) Weight of Pan + Oven- Dry Aggregate Weight of Pan Weight of Submerged Aggregate Weight of Pan + SD Aggregate 0.8495 Ib 1.9885 lb 0.6870 lb 1.9630 Ib 2. If the Moisture Content of a stockpile sample of the same coarse aggregates is 1.85 %, what is the moisture state of aggregate sample? Select from the four standard moisture states. Explain how you arrived at the answer. 3. If Bulk unit weight of coarse aggerates is 98 Ib/ft³determine the % Voids of dry-rodded aggregate. Youlk S.G(Bulk Dry)*Pwater %Solids * 100 4. Determine the % solids for 2 cases discussed in pre-lab video by using below data.…
Sieve analysis test for fine aggregates was performed on a sample of fine aggregates and produced the following results: a. Calculate the percent passing through each sieve. b. Plot the percent finer in a semi-log gradation chart. c. What is the maximum aggregate size of the sample? d. What is the nominal maximum aggregate size of the sample? e. What is the fineness modulus? Is it in typical range? " Sieve Size, 9.5 4.75 3.35 2.36 2.00 1.18 0.85 0.60 0.425 0.30 0.25 0.18 0.15 (No. 0.075 Pan mm (in) (3/8) (No. 4) (No. 6) (No. 8) (No. 10) (No. 16) (No. 20) (No. 30) (No. 40) (No. 50) (No. 60) (No. 80) 100) (No. 200)| Amount 25 59 75 86 115 136 169 192 225 198 173 112 90 33 12 Datained.

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS