H.W/ By using ASD and LRFD methods, find a light section W12xw of A992 steel material of member BC in the figure below assumed the connection at the flange of two lines (6 %). Key of solution: The distance between A and C is 17.3 feet 22015 oli to bionns After analysis the forces.... BC-323.4 kip. B 280' kip A omolo la aixa fanilan nola bilqqa 10 d

H.W/ By using ASD and LRFD methods, find a light section W12xw of A992 steel material of member BC in the figure below assumed the connection at the flange of two lines (6 %). Key of solution: The distance between A and C is 17.3 feet 22015 oli to bionns After analysis the forces.... BC-323.4 kip. B 280' kip A omolo la aixa fanilan nola bilqqa 10 d

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.7.10P: Three round, copper alloy bars having the same length L but different shapes are shown, in the...

See similar textbooks

Similar questions

A rigid weightless be am SUPPorted at the point D by the pixed goint loo ded by the momend M is Support and points B and c holding the beam horisonta lly . a + the ver tical bs connected are For the data listed below determne ! Data > E = 2.1x10$ MPa gie ld stres 6y: 250 MPa , foctor oc Sofety Sr-1.S * Necessoy are a wetion A ? Of Cross - Other Data ; I 5 cM , a : U cm Ma SONM Safety · design method ond limit-state- mordatory. * Use both, Factorr design netled. Both net hats A.E 2A a
Imagine that you have drawn a FBD of member AB. What will be the easiest way to write an equation involving ?unknowns at B 0.9 m 0.8 m 500 N 45° 0.5 m 1.2 m 0.4 m E MB = 0 .a O E Fx = 0 .b O E MA = 0 .c O EMc = 0 .dO
Problem # 23. fowe for x applied Connection. the reaction forces if a 40-kN force on the Ateel rod, rear and fow ards the Given: aoteel rod alloy aluminum alboy 40 30 Cm Aleel nod has -em diameter A 40 cm lona wherein diameter Young a moduluad of steel = 200 6Pa tounga modulua of aluminum = \20 6 Pa The poda are attached to gether and both^ are Constrainedo. alloy a 30- em long alliminum alloy with D.5 cm A Connectud on ts end. sidera
Quesron L UESTION from beading Support Diperenticte nomal caial looding your answer with neat explanatory sketches that show the possible tyes f type of loading de formation resulting from each
Let's considera rod having a solid circular cross-section with diameter of 4 mm and it is made of a material having a Young's modulus E= 200 Gpa and a Poisson's ratio of 0.3. If a tensile force Fis subjected to that rod cross-section, the diameter becomes 3.995 mm. determine the applied force F Select one: OF 5236 N O F=15708 N Clear mopshoe Finish attempt
1. Find the internal force of member EG, FH, and FG using method of sections. 0.866 m 3KN 5 @ 1m
An AISI 1050 HR solid tube of 20mm diameter is acted by force F1 = IkN, and force F2 of 2kN. The tube is welded to a larger round base by 3mm fillet weldment, the base is connected to the ground base (shown in gray color) by means of four bolts M8x1.25mm (property class of 4.8)). The bolts are evenly distributed at 20mm away from the center of the tube. R=100 F1 120 120. F2 R=100 D =20 120 R=3 D =60 40 Dimensions are in mm Perform the following the following: 1- Find the state of stress for the most critical point on the assembly and build the mohr's circle. Solve question 1
Uuestion 1: Calculate the axial load of spiral column with respect to first and second peaks. Materials used are C25 and S420 for longitudinal bars of 8- 024 and for spirals. Use the design strength of concrete and steel. 2. A, fywk 0, = D (s) 4. Ao P. = D (s) fa = f+4.0-0, GAP fa 4. f ynk (A min p, = 0.45. , min p, = 0.12. ywk D=550 mm H=600 mm Spiral : 010/85 mm 200 mm
Clear my choice Let's consider a rod having a solid circular cross-section with diameter of 4 mm and it is made of a material having a Young's modulus E= 200 Gpa and a Poisson's ratio of 0.3. If a tensile force Fis subjected to that rod cross-section, the diameter becomes 3.995 mm. determine the applied force F. Select one: O F= 5236 N OF=15708N O F= 13090 N OF=10472 N OF=4189 N O F=6283 N Clear my choice Finish attempt NEXT ACTIVITY MENG360 Test -Spring 2020-2021 Jup to
Question 4 of 10 -/ 10 Current Attempt in Progress AWT205 x 30 structural steel section (see Appendix B for cross-sectional properties) is used for a 6.6 mcolumn. Assume pinned connections at each end of the column. Determine: (a) the slenderness ratio. (bi the Euler buckling load. Use E- 200 GPa for the steel. (c) the asdal stress in the columnwhen the Euler load is applied. Part 1 Use Appendix B to lookup the cross-sectional area, the area moment of inertia, and the radius of gyration for a WT205 x 30 structural steel section. Answer A x 10 mm mm x 10 mm mm
I already found Ax=0,Ay=11.2 and Fy=11.2 how do I find the theta to solve for member AB? also state if the members are is tension or compression.
CONCEPTUAL: 1. Consider a deformable homogenous siender rod of constant area along its length. It is axially loaded at points A and C. According to Saint-Venant's Principle, which of the following point(s) islare the actual maximum axial stress underestimated the most by the average stress? B F L PROBLEM SOLVING: A rigid bar is supported by three non-rigid steel rods, as shown. Rods AB and FG are 0.8m long with a cross-sectional diameter of 30mm. Rod CDE is made up of equally-long 0.40-m CD and DE whose cross-sectional diameters are 60mm and 30mm, respectively. A 45KN downward load is applied to the rigid bar. There is no initial strain before the application of the load. Let E steel-200GP. 2. Determine the internal forces on rods AB, CDE, and FG 3. Determine the displacement of the rigid bar. 4. If the allowable displacement of the horizontal rigid bar is 0.071mm downwards, what maximum allowable vertical load can be applied for a factor of safety of 3? 0.40 m 60mm D 0.8 m 30mmo 0.8 m…