Given the symmetrical components to be VO = 10<0 V , V1 = 80<30 V , V2 = 40<-30 V determine the unbalanced phase voltages Va, Vb, and Vc. (b) Using the results of part (a), calculate the line-to-line voltages Vab, Vbc, and Vca. Then determine the symmetrical components of these line-to-line voltages, the symmetrical components of the corresponding phase voltages, and the phase voltages.

Given the symmetrical components to be VO = 10<0 V , V1 = 80<30 V , V2 = 40<-30 V determine the unbalanced phase voltages Va, Vb, and Vc. (b) Using the results of part (a), calculate the line-to-line voltages Vab, Vbc, and Vca. Then determine the symmetrical components of these line-to-line voltages, the symmetrical components of the corresponding phase voltages, and the phase voltages.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter8: Symmetrical Components

Section: Chapter Questions

Problem 8.6P

See similar textbooks

Similar questions

Power in a three phase delta system with balanced load is equal to (Sqrt (3)) (VL) (IL) (p.f.) (Sqrt (3)) (Vph) (Iph) (p.f.) (Sqrt (3)) (VL) (Iph) (p.f.) O (Sqrt (3)) (Vph) (IL) (p.f.)
In a three-phase system voltage, assume that the phase-to-neutral voltage at phase “b” is considered as the reference (zero phase angle). 1. State the positive sequence and the negative sequence. 2. Solve the following for both sequences: a. the line-to-neutral voltages : VAN ,VBN and VCN b. the line-to-line voltages : VAB , VBC and VCA
A balanced three phase voltage of 360-V line-to-neutral is applied to a balanced Y-connected load with ungrounded neutral, as shown in figure-1. The three phase load consists of three mutually- coupled reactances. Each phase has a series reactance of Z, = j24 N, and the mutual coupling between phases Zm = j6 N. (i) Evaluate the line currents by mesh analysis without using symmetrical components. Evaluate the line currents using symmetrical components. (ii) j6 j24 j6 V. Figure-1
2. The one-line diagram of a three-phase power system is as shown in the figure below. Impedances are marked in per unit on a 100-MVA, 400-kV base. The load at bus 2 is S2 = 15.93 MW-j33.4 Mvar, and at bus 3 is S3 = 77 MW +j14 Mvar. It is required to hold the voltage at bus 3 at 4006 0 kV. Working in per unit, determine the voltage at buses 2 and 1. V3 j0.5 pu V₂ S₂ j0.4 pu S3
In Figure 1, the 3-phase source has a line-to-line voltage of 440 volts. The details of the impedances are the following: Z₁ = 36-j15; Z₂ = 40 + /300; Z₂ = 45+j60 ; Z₂ = 75 + jo ; Z5 = 50+j50; Z6 = 20+ j48 2. Determine the following: (a) Line currents: labi, and I (c) Line currents: lar, Ibr, and ICT; (b) Line currents: Iaz, Ibz, and Iczi (d) PT, QT, ST, and pft for the system; (e) W, and W, readings for 2-wattmeter method at lines a and b. Balanced 3-Phase ab-bc-ca source C Figure 1 →laT -Ibr -KT 1 lal ²3 ↓ Ibi 1 Ici la2 lb2 le2ܝ 150 1²₂ OND
Calculate the initial symmetrical short circuit current that will occur when a 3 phase short circuit error occurs at the F point in the Figure below İ k3 phase-max ?
Question 3. A three-phase impedance load balanced D a connected load in parallel with a balanced ? connected load made of bonding. D each arm for the load ?D = 6 + 6? and ? each arm for the connected load It is given as ?? = 2 + 2?. ? the connected load ?? = 1? is earthed through the neutral impedance. To this impedance load, the symmetrical component voltages ?0 = 10∠60°, ?1 = 100∠0° and ?2 = Unbalanced phase-to-earth voltages ??, ?? and ?? of 15∠200° volts were applied. a) Draw the zero, positive and negative sequence circuits. b) Find the complex powers imparted to each component circuit.
2_ What case/cases in which the measured phase current include the three symmetrical components ( +,,0).( Rather than the unbalanced load/source voltage case)
2) The one-line diagram of a three-phase power system is as shown in Figure. Impedance are marked in per-unit on a 100-MVA, 400-kV base. The load at bus 2 is S2=15.93 MW - j33.4 Mvar, and at bus 3 is S3-77 MW + j14 Mvar. It is required to hold the voltage at bus 3 at ...L0 kV. Working in per-unit, determine the voltage at buses 2 and 1. (Please determine the voltage magnitude within the specified limits: 410-450 V. By considering the voltage magnitude value you determined yourself, solve the question.) V₁ j0.5 pu V₂ j0.4 pu S₂ Figure V3 S3
Select the base voltages for one section and calculate the base voltages for the rest of the sections. Remember that the voltages given are line-line. Calculate the current and impedance for all sections of the System. Assume a base complex power of 100 MVA.
of stion 4 A single phase transmission line is delivering 450 kVA load at 12 kV. Its resistance is 4.5 2 and inductive reactance is 6 2. If the load power factor is 0.9 lagging. Determine the Current through the line Sending end voltage Sending end power factor Regulation of transmission line Efficiency of transmission line A load of 120 MW at a power factor of 0.8 lagging can be delivered by a 3-phase transmission line. The voltage at the intained at 33 kV and the loss in the transmission as 7.5 % of the power delivered. (Consider
3. A balanced delta connected load of "X" Q- per phase is connected at the end of a three-phase line. The line impedance is "G" - per phase. The line is supplied from a three-phase source with a line-to-line voltage of 207.85 Vrms. Taking phase "a" voltage Va as reference, determine the following: (a) Current in phase a. (b) Total complex power supplied from the source. (c) Magnitude of the line-to-line voltage at the load terminal. X-13+16j G=3+6j