Given the decoder circuit for an 8086-based memory module below,IC2AXA19XA18216KA17474LS21NIC1A1XA15212CE1*13IC3AXHBE*74AS10N74LS04NIC1B3IC4ACEO*1574LS04N74AS1ONif the address on the address bus FFFF0, what is the status of CE1* when the processor performs a memoryread and that a word (16 bits) is read? Note that the unlabeled input for the NAD gate is XA16.

Given Logic circuit: Aim:To find the status of CE1 for the memory read…

Given the decoder circuit for an 8086-based memory module below, XA19 XA18 2 1 IC2A XA17 4 5 XA15 XHBE* 1 XAO 1 74LS21N IC3A 6 74LS04N IC4A 74LS04N 1 23 2 13 345 4 5 IC1A 74AS10N IC1B 74AS10N 12 CE1* CEO* if the address on the address bus FFFFO, what is the status of CE1* when the processor performs a memory read and that a word (16 bits) is read? Note that the unlabeled input for the NAD gate is XA16.

Given the decoder circuit for an 8086-based memory module below, XA19 XA18 2 1 IC2A XA17 4 5 XA15 XHBE* 1 XAO 1 74LS21N IC3A 6 74LS04N IC4A 74LS04N 1 23 2 13 345 4 5 IC1A 74AS10N IC1B 74AS10N 12 CE1* CEO* if the address on the address bus FFFFO, what is the status of CE1* when the processor performs a memory read and that a word (16 bits) is read? Note that the unlabeled input for the NAD gate is XA16.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

4) Design and draw these memory units with their control circuits. Explain operations. a) A single EPROM 2716 is used with an 8088 microprocessor so that this microprocessor will see only X bytes of memory between the address range of DF800 –DFFFF or DD800 - DDFFF instead of 1M byte that it expects. Draw this circuit. What are X bytes? Do not use 74138 decoders. b) Design and show a 16K x 16-bit memory circuit by using 8K x 8-bit RAMS. Explain its operation. Do not use decoder 74138 chip.
If R0 = 0x20008000, after run STMDB r0!, {r3, r9, r7, r1, r2} command what is the r7 register memory start address?A. R0= 0x20007ff4B. R0 = 0x20007ffefC. R0 = 0x20007fffD. R0=0x20007fecE. R0 = 0x20007ff0
d) Draw the schematics of 4-bit synchronous and asynchronous MOD-8 counters and comment on their pros and cons. e) Calculate the noise margin for a logic gate with the following logic levels: VIL = 1.1 V, VIH = 3.2 V, VOL = 0.6 V, VOH = 4.0 V.
P Flag question Explain the MUL instruction of 8086. Compare it with IMUL instruction. (1 +1 Marks) Write a Assembly language program for 8086 to find the cube of a number using MUL instruction. (5 Marks) (Note : Solve the question in paper, scan and upload along with the other Part B and C answers) B I III
8085 microprocessor went through its manipulation operation in the ALU, the results was transferred on the data bus and status of the results was stored in the flag register for indications . With your knowledge and understanding illustrate a complete bit configuration of 8085 flag register and show the functions of the represented bits in the register.
(a). If I want to store 4-bit data 0110 and at 4th clock I want to extract all the stored bits, which shift register I should explain it with the help of circuit diagram and table. (b). Write comparison between Diode transistor logic and Transistor Transistor logic
1. Write the contents of all registers and the conditions codes registers after each execution instructions in Table Q1(a). Instructions SUBS r0, rl, 12 MOV 12,13, ASR #3 ro 11223344 Table Q1 (a) rl F7770025 12 r3 CF119856 CF119856 NZ V C 010 1
Assume register R0, R1 and R2 contain the value of 0x00000100, 0xAABB1122 and 0x00000102. ARM Cortex-M3 processor executes the instructions STR R1, [R0] and LDRB R1, [R2] in sequence. What is the content of register R1 if the storing mode of data in memory using Little Endian Mode? A. 0xAABB11BB B. 0xAABB1111 C. 0xAABB1122 D. 0x0000BBAA E. 0x00001122
For a microprocessor similar to ATmega328p an 8 bit ADC uses a VREF = 3.3 V. When an analog read is executed the return value is 112. What Voltage is present on the input? Enter the value in the box provided in mV. Round to the nearest mV.
1E. Write a VHDL code for all Logic Gates and verify Output waveforms. 2E. Write a VHDL code for Half Adder and verify Output waveforms. 3E. Write a VHDL code for Full Adder and verify Output waveforms.
Given the 74LS147 Encoder TINKHK167006 Logic Symbol 56679AWN 74LS147 (a) What would be output if input 1,2, and 7 were activated simultaneously. (b) Sketch the wiring diagram for input 1,5, and 8 with push button as user input.
Suppose we have two registers, Rl and R2, and between them we have a combinational logic circuit. The tpcg = 0.5 ns, tccq = 0.25 ns, tpd = 4 ns, tcd = 2.5 ns, tsetup = 0.5 ns and thold = 0.2 ns. What is the maximum value of fc? Select one: a. 0.2 ps O b. 200 MHz O c. 2 GHz O d. 200 KHz