Given: Draw ㅑ the 2 Kip/FE 5 Ft A shear + and 5 Ft moment 30 kip-ft 5 ft diagram. B

Q: a) 8 kips. 16²7 36 kips 16' E B 24 kips 12 12² ↓

A: As per Bartleby's guidelines we are supposed to answer only first question. Kindly repost other…

Q: For each of the three floating bodies, determine the buoyant force exerted by the liquid. Each body…

A: Objective: To determine the bodies which are subjected to the greatest and least buoyant force.…

Q: a) A 10 m 30 kN B 50 kN C 5 m

A: Given, Cantilever beam with loading   To find : Support reaction

Q: beam is supported by a roller and a hinge at its extremities. The 2 kN/m is loaded entirely on its 4…

A: According to given data     beam is supported by a roller and a hinge at its extremities. The 2 kN/m…

Q: In an oedometer test on a saturated specimen (G,- 2.70, the initial thickness Ho-2.0cm), when the…

A: According to given data In an oedometer test on a saturated specimen (G,- 2.70, the initial…

Q: The homogeneous bar ABCD shown in Fig. P-114 is supported by a cable that runs from A to B around…

A: Given Data : Allowable stress in each cable = 100 MPa Area of cable AB = 250 mm2 Area of cable C =…

Q: Q2. Show that p = Cr² (α = 0 + sin cos 0 - tan a cos² 0) is a permissible Airy 1 function for the…

A: Solution:- Given:- ϕ = Cr2α-θ+sinθ×cosθ-tanα×cos2θThis funation to be airy function it should…

Q: Using Moment Distribution Method, compute the moments at A, B and C. El is constant.

A:

Q: Please copy paste ans other wise down vote

A:

Q: Calculate the magnitude of the resultant force (in kN) of the distributed load shown below. Provide…

A:

Q: Homework: Determine the forces in all members for the truss shown below. 20 KN В C ти E 5 KN A 10 KN…

A:

Q: e total vertica

A: Given: Depth of water in a lake is 12 m Total unit weight is 18.2 kN/m3

Q: 15 kN/m A 3 m B 20 KN 1m- C -1 m-

A: Solution:- Given data:- UDL = 15 kN/mSpan of beam = 5 m To find:- The support reactions at A and C…

Q: The trusses are pin connected and suspended from the parabolic cable. If the structure is pin at B,…

A:

Q: Given the following data: SSD = 430’ G = +3% Tpr = 2.5 sec Will the speed/velocity be acceptable…

A:

Q: 2. A propped beam shown below is subjected to a uniformly distributed load w and a concentrated load…

A:

Q: Determine the forces in all members for the truss shown below. 20 KN 5 KN A 10 KN 3m B + 3m C 30 KN…

A: Given Data  Find force in each member.

Q: 60 KN 30⁰ 40 KN W What weight W is necessary to start the of system. blocks shown in the figure…

A:

Q: The free mean speed of a roadway is found to be 80 km/hour. Under stopped condition the average…

A: Given data: The free mean speed of a roadway = 80 km/hr The average spacing between vehicles = 8 m

Q: shear-force diagram to j Odownward upward

A:

Q: N N Z+

A:

Q: Question A triangular direct runoff hydrograph due to a storm has a time base of 90 hours. The peak…

A: Given- Time base b=90 hrs, Peak flow Q=60 m3/s @ 20 hrs, Area A=300 km2,

Q: Problem 014 From Fig. P-014, P is directed at an angle a from x-axis and the 200 N force is acting…

A:

Q: From the following data of a freeway surveillance, there are 4 vehicles counted for  a length of 200…

A:

Q: Use E= 200 GPa, I = 800 x 106 mm² when necessary. P = 229kN For the beam loaded as shown, determine…

A: Data given Find: Reaction components

Q: The bearing to the backsight is N65°W.  The turning (horizontal) angle to a topographic shot is…

A: Given: B.S = N 65o W Angle = 173o To find: The bearing to said topographic shot

Q: An aerated BOD bottle is filled with substrate and microbial cells. You have determined the…

A: Given, Y = 0.60  μ = 2/day Ks = 25 mg/L dSdt = 15000 mg/L-hr S = 275 mg/L

Q: A negative internal bending moment M causes a beam element to O rotate counterclockwise bend concave…

A: Bending moment at a given section can cause Sagging (concave upward) or hogging (concave downward)…

Q: Problem A 300 mm x 600 mm reinforced concrete beam section is reinforced with 4 -28-mm- diameter…

A: Given : Reinforced concrete beam section = 300 mm X 600 mm Tension steel = 4 - 28 mm d = 536 mm…

Q: For the beam shown (E = 200 GPa, A=12 cm², I-9 cm¹), determine: a) Reactions at A and C. b) Draw the…

A:

Q: 1. The average annual precipitation for the four sub-basins constituting a large river basin is…

A: Given Data : Precipitation, P (inches) Area, A (sq. mi) 39.0 30 44.20 275 33.40 420 28.00…

Q: Describe three different methods of manufacturing a crankshaft and describe the machining  and…

A: During vehicle movement, the crankshaft converts the vertical movement of the pistons into…

Q: 17.17 Member BC of the pin-connected truss has a cross sec- oy = 42 ksi. tion as shown. E = 29 x 10³…

A: Given: E=29000 ksify=42 ksi For 2 C10×30, A=17.64 in2rx=3.43 inry=1.32 in To determine: Load P.

Q: Q- A photographic survey is carried out to a scale of 1: 20000. A camera with a wide angle lens of…

A:

Q: Question A triangular direct runoff hydrograph due to a storm has a time base of 90 hours. The peak…

A:

Q: Calculate the minimum passing sight distance required for a two-lane rural highway that has a posted…

A: Solution: Given: Speed Of passing Vehicle V=76kph The average speed of impeder vehicles Vi=64kph The…

Q: Given the radius (R) of a horizontal curve = 2864.79' What is the degree of curve (Daº) ? Answer in…

A: GIVEN DATA   Radius  R = 2864.79 ' To calculate degree of curve   =?

Q: Homework: Determine the forces in all members for the truss shown below. 5 KN A 10 KN 3m B E 20 KN…

A:

Q: Describe the six grades of hardwood veneers.

A: Hardwood:- Dicot trees produce hardwood as their wood. Broad-leaved temperate and tropical forests…

Q: Given the following isometric drawing, draw the top view, front view, and right side view

A:

Q: What is the aeroplane flying height to obtain the average scale of the photograph equal to 1/7200?…

A: Given data: The average scale of the photograph, S = 1/7200 Ground surface elevations vary 160 m to…

Q: Using the method of joints, calculate the force in each member of the trusses shown. State whether…

A:

Q: EXAMPLE 6.4 A concrete beam having a rectangular section 100 mm wide and 300 mm deep is prestressed…

A: Given: The width of a beam is 100 mm. The depth of a beam is 300 mm. The initial force is pi=240 kN.…

Q: The long chord from PC to PT of a compound curve is 320m long, and the angles it makes with the…

A:

Q: n oil flow rate of 0.012 m³/s is required in an industrial process. The flow system includes a…

A: According to given data An oil flow rate of 0.012 m³/s is required in an industrial process. The…

Q: A particle is confined to move along the horizontal slot due to the rotation of the arm as shown in…

A: Figure is as shown

Q: cause the bending-mor ump Odownward O upward

A:

Q: Calculate the magnitude of the resultant moment (in kN-m) about point J of the three 4-kN downward…

A:

Q: Describe the basic properties of steel frames.

A: This question is related to the Design of Steel Structures from Civil Engineering.

Q: Permeability tests were carried out on the samples collected from two different layers as shown in…

A: Given- Horizontal & vertical permeabilities are given- kh1=4.4×10-3 m/s,kh1=6×10-1…