G B Select one or more: a. Minimal reduction in cross sectional area b. Significant elongation to failure c. The component breaking into many pieces d. Cavity Coalescence e. A smooth fracture surface Previous page Next

G B Select one or more: a. Minimal reduction in cross sectional area b. Significant elongation to failure c. The component breaking into many pieces d. Cavity Coalescence e. A smooth fracture surface Previous page Next

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Compute the minimum critical surface crack (edge crack) length if the fatigue life must be a minimum of 5.0 x 106 cycles. Assume the initial maximum edge surface crack length of 1.80 mm and a maximum tensile stress of 160 MPa and minimum stress of 0 MPa. Assume m = 1.8 and A= 7.5 x 1013 in MPa and meter units, Assume Y= 1.25. O a. 4.26 mm O b. 5.38 mm OC. 2.36 mm O d.0.125 m
Given: Metal Specimen diameter x-sectiion (circular)= 0.55 in Gage Length= 2.030 in Fracture bccurved at 28,500 pounds final length= 2.30 in Final diameter= 0.43 in Determine: a) Ultimate tensile stress in ksi
Question 2 A machine component is made of Aluminium alloy having an ultimate tensile stress Ou = 350MPa, a fracture toughness Kic= 40 MPa√m and a geometry factor Y=1.12. The component is subject to cyclic tensile stress of 200 MPa and cyclic compressive stress of 70 MPa. Before the operation, using an ultrasonic non-destructive testing technique, it was found that there is an edge crack of length 2mm. The crack growth C(AK)m, where is in m/cycle, AK ΔσΥ νπα , C ~ 2.2×10-12 da rate is given by da dN dN and m=3.2. Find the critical crack length. = =
A Plexiglas model of a gear has a 1 mm crack formed in its fillet curve (where the tensile stress is maximum). The model is loaded until the crack starts to propagate. Y=1.5. How much higher a lod can a gear (made of AISI 4340 steel tempered to 425°C) carray with the same crack and the same geometry?
la. In the design of a pressure vessel, the leak-before-break criterion is used considering the circumferential wall thickness and the plain strain fracture toughness. The design is limited by the yield strength gs and the factor of safety (SF). Derive expressions for the critical crack size. 1b. Calculate the design stress and stress intensity factor if the safety factor is 1.5. Data: gxS = 586 MPa and KIC = 33 MPa m1/2.
Given: Metal Specimen diameter x-sectiion (circular)= 0.55 in Gage Length= 2.030 in Fracture bccurved at 28,500 pounds final length= 2.30 in Final diameter= 0.43 in Determine: a) Reduction of a x-sect. area as a percentage
1. A bronze alloy specimen having a diameter of 12.8 mm and a gage length of 50 mm was tested to fracture. Stress and strain data obtained during the test are shown in Figure. Determine: 400 Upper scale a. the modulus of elasticity. b. the proportional limit. c. the ultimate strength. 320 Lower scale 240- d. the yield strength (0.20% offset). 160 e. the modulus of resilience. f. the true fracture stress if the 80 final diameter of the specimen at the location of the fracture was 10.5 mm. 0.100 0.200 0.300 0.400 0.005 0.010 0.015 0.020 g. The Poisson's ratio. Strain (mm/mm) Stress (MPa)
A bronze alloy specimen having a diameter of 12.8 mm and a gage length of 50 mm was tested to fracture. Stress and strain data obtained during the test are shown in Figure. Determine: 400 - Upper scale a. the modulus of elasticity. 320 b. the proportional limit. Lower scale c. the ultimate strength. 240 d. the yield strength (0.20% offset). 160 e. the modulus of resilience. f. the true fracture stress if the 80 final diameter of the specimen at the location of 0.100 0.005 0.300 0.015 0.200 0.400 the fracture was 10.5 mm. 0.010 0.020 g. The Poisson's ratio. Strain (mm/mm) Stress (MPa)
ASAP
Tensile engineering stress-strain curves through failure are depicted below. Which specimen features the highest toughness? Engineering Stress, MPa 1800- 1600- 1400- 1200- 1000- 800- 600- 400- 200- Ol 0 Aluminum Alloy 2024-T81 0.04 0.08 Stainless Steel (18-8) 1340 Steel, Water-Quenched & Tempered at 370 C Magnesium 0.12 Structural Steel (Mild Steel) Engineering Strain 0.16 1340 Steel, Water-Quenched & Tempered at 370°C Aluminum Alloy 2024-T81 Structural Steel (Mild Steel) Stainless Steel (18-8) Magnesium 0.20 0.24
Q1. (i) Initial strain Please enter your supplied question data Q1. (ii) Eo B (hr¹Pa-¹) n IVICUITO Fracture 0.003 Please enter your answers here Your Q1. (i) Answers: 4.60E-34 Q1. (ii) 3.2 Q2. o (Pa) σo (Pa) 780,000,000 Q3. t (hr) Q2. A component is made from a metal that is known to be viscoelastic and behaves according to a secondary creep rate equation with constants of B and n provided as your input values. If the component is subjected to a constant force that results in the initial strain of E provided to you, determine the design stress for a secondary creep life of 1,000 hrs before attaining a limiting strain, &, of 0.01. Q3. If the same component is subjected to a constant displacement that results in the value of initial stress, o, provided to you, calculate the time for the stress to reduce to 200MPa. Young's modulus of the bolt is E = 200GPa.
Q10: A cylindrical specimen of steel having an original diameter of 12.8 mm is tensile tested to fracture and found to have an engineering fracturestrengtho; of 460 MPa. Ifits cross-section diameter at fracture is 10.7 mm. determine 1) The ductility in terms of percentagereduction in area. 2) The truestress at fracture.